• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 933-1:2012

Current
Current

The latest, up-to-date edition.

Tests for geometrical properties of aggregates - Part 1: Determination of particle size distribution - Sieving method
Published date

11-01-2012

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Preparation of test portions
7 Procedure
8 Calculation and expression of results
9 Test report
Annex A (normative) - Alternative test method for
        all-in aggregate with D >= 31,5 mm
Annex B (normative) - Test method for aggregates
        unsuitable for oven-drying
Annex C (informative) - Example of test data sheet
Annex D (informative) - Graphical presentation of results
Bibliography

This European Standard describes the reference washing and dry sieving method used for type testing and in case of dispute, for determination of the particle size distribution of aggregates. For other purposes, in particular factory production control, other methods may be used, provided that an appropriate working relationship with the reference method has been established. It applies to all aggregates, including lightweight aggregates, up to 90 mm nominal size, but excluding filler. NOTE 1The determination of the grading of fillers is specified in EN 933-10 Assessment of fines — Grading of filler aggregates (air jet sieving).NOTE 2Dry sieving without washing may be used for aggregates free from particles which cause agglomeration.

Committee
CEN/TC 154
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

Standards Relationship
NS EN 933-1 : 2012 Identical
NF EN 933-1 : 2012 Identical
I.S. EN 933-1:2012 Identical
UNE-EN 933-1:2012 Identical
SN EN 933-1:2013 Identical
NBN EN 933-1 : 2012 Identical
NEN EN 933-1 : 2012 Identical
PN EN 933-1 : 2012 Identical
DIN EN 933-1:2012-03 Identical
SN 670902-1 : 2013 Identical
UNI EN 933-1 : 2012 Identical
BS EN 933-1:2012 Identical
NS EN 993-1 : 1ED 1995 Identical

S.R. CEN TS 14243:2010 MATERIALS PRODUCED FROM END OF LIFE TYRES - SPECIFICATION OF CATEGORIES BASED ON THEIR DIMENSION(S) AND IMPURITIES AND METHODS FOR DETERMINING THEIR DIMENSION(S) AND IMPURITIES
PREN 932-5 : DRAFT 2009 TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION
I.S. EN 13108-8:2016 BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS - PART 8: RECLAIMED ASPHALT
BS EN 1176-1:2017 Playground equipment and surfacing General safety requirements and test methods
09/30207822 DC : 0 BS EN 15600-1 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
BS EN 14227-15:2015 Hydraulically bound mixtures. Specifications Hydraulically stabilized soils
BS EN 13285:2010 Unbound mixtures. Specifications
DIN EN 15600-1:2010-12 Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation
BS EN 15732:2012 Light weight fill and thermal insulation products for civil engineering applications (CEA). Expanded clay lightweight aggregate products (LWA)
02/102929 DC : 0 PREN 14440 - SLURRY SURFACING - FACTORY PRODUCTION CONTROL
DIN EN 15732:2013-01 LIGHT WEIGHT FILL AND THERMAL INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS (CEA) - EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA)
06/30155785 DC : 0 BS EN 15564 - PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS
09/30209668 DC : 0 BS EN 16025-1 - THERMAL AND/OR SOUND INSULATING PRODUCTS IN BUILDING CONSTRUCTION - BOUND EPS BALLASTINGS - PART 1: REQUIREMENTS FOR FACTORY PREMIXED EPS DRY PLASTER
PREN 13450 : DRAFT 2015 AGGREGATES FOR RAILWAY BALLAST
02/101684 DC : DRAFT FEB 2002 PREN 14316-1 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
DD ENV ISO 10722-1:1998 Geotextiles and geotextile-related products. Procedure for simulating damage during installation. Installation in granular materials
04/30110128 DC : 0 BS EN 14243 - POST-CONSUMER TYRE - MATERIALS AND APPLICATIONS
PREN 13108-20 : DRAFT 2013 BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS - PART 20: TYPE TESTING
UNI EN 12273 : 2008 SLURRY SURFACING - REQUIREMENTS
I.S. EN 1367-6:2008 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 6: DETERMINATION OF RESISTANCE TO FREEZING AND THAWING IN THE PRESENCE OF SALT (NACL)
DIN EN 12697-2 E : 2015 BITUMINOUS MIXTURES - TEST METHODS - PART 2: DETERMINATION OF PARTICLE SIZE DISTRIBUTION
I.S. EN 12273:2008 SLURRY SURFACING - REQUIREMENTS
I.S. EN 1744-8:2012 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 8: SORTING TEST TO DETERMINE METAL CONTENT OF MUNICIPAL INCINERATOR BOTTOM ASH (MIBA) AGGREGATES
UNI EN 13285 : 2010 UNBOUND MIXTURES - SPECIFICATION
PREN 14243-3 : DRAFT 2017 MATERIALS OBTAINED FROM END OF LIFE TYRES - PART 3: SHREDS, CUTS AND CHIPS - METHODS FOR DETERMINING THEIR DIMENSION(S) INCLUDING PROTRUDING FILAMENTS DIMENSIONS
PREN 13383-2 : DRAFT 2017 ARMOURSTONE - PART 2: TEST METHODS
UNI EN 15732 : 2012 LIGHT WEIGHT FILL AND THERMAL INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS (CEA) - EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA)
PREN 16809-1 : DRAFT 2014 THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED PRODUCTS FROM LOOSE-FILL EXPANDED POLYSTYRENE (EPS) BEADS AND BONDED EXPANDED POLYSTYRENE BEADS - PART 1: SPECIFICATION FOR THE BONDED AND LOOSE FILLED PRODUCTS BEFORE INSTALLATION
EN ISO 10722:2007 Geosynthetics - Index test procedure for the evaluation of mechanical damage under repeated loading - Damage caused by granular material (ISO 10722:2007)
EN 12697-1 : 2012 COR 2012 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT
DIN EN 14227-5:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND GRANULAR MIXTURES
DIN EN 933-8:2015-07 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 8: ASSESSMENT OF FINES - SAND EQUIVALENT TEST
DIN EN 14227-3:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND GRANULAR MIXTURES
DIN EN 13286-2:2013-02 Unbound and hydraulically bound mixtures - Part 2: Test methods for laboratory reference density and water content - Proctor compaction (includes Corrigendum :2012)
BS EN 1097-9:2014 Tests for mechanical and physical properties of aggregates Determination of the resistance to wear by abrasion from studded tyres. Nordic test
BS EN 13450:2013 Aggregates for railway ballast
BS EN 1097-1:2011 Tests for mechanical and physical properties of aggregates Determination of the resistance to wear (micro-Deval)
BS EN 13242:2013 Aggregates for unbound and hydraulically bound materials for use in civil engineering work and road construction
UNE-EN 14227-5:2014 Hydraulically bound mixtures - Specifications - Part 5: Hydraulic road binder bound granular mixtures
BS EN 1367-3:2001 Tests for thermal and weathering properties of aggregates Boiling test for Sonnenbrand basalt
BS EN 14227-13:2006 Hydraulically bound mixtures. Specifications Soil treated by hydraulic road binder
BS EN 13043:2013 Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas
BS EN 13294:2002 Products and systems for the protection and repair of concrete structures. Test methods. Determination of stiffening time
I.S. EN 1097-1:2011 TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 1: DETERMINATION OF THE RESISTANCE TO WEAR (MICRO-DEVAL)
I.S. EN 15330-1:2013 SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 1: SPECIFICATION FOR SYNTHETIC TURF SURFACES FOR FOOTBALL, HOCKEY, RUGBY UNION TRAINING, TENNIS AND MULTI-SPORTS USE
I.S. EN 14227-1:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
DIN EN 14227-10:2006-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 10: SOIL TREATED BY CEMENT
DIN EN 14316-1:2004-11 Thermal insulation products for buildings - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation; German version EN 14316-1:2004
EN 13294:2002 Products and systems for the protection and repair of concrete structures - Test methods - Determination of stiffening time
DIN EN 12697-1:2012-09 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT
I.S. EN 13286-4:2003 UNBOUND AND HYDRAULICALLY BOUND MIXTURES - TEST METHODS FOR LABORATORY REFERENCE DENSITY AND WATER CONTENT - PART 4: VIBRATING HAMMER
DIN EN 14227-14:2006-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 14: SOIL TREATED BY FLY ASH
EN 13108-8:2016 Bituminous mixtures - Material specifications - Part 8: Reclaimed asphalt
EN 13075-2:2016 Bitumen and bituminous binders - Determination of breaking behaviour - Part 2: Determination of fines mixing time of cationic bituminous emulsions
DIN EN 14317-1:2004-11 Thermal insulation products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation; German version EN 14317-1:2004
CEN/TS 16637-3:2016 Construction products - Assessment of release of dangerous substances - Part 3: Horizontal up-flow percolation test
EN 12697-15 : 2003 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 15: DETERMINATION OF THE SEGREGATION SENSITIVITY
EN 1097-1:2011 Tests for mechanical and physical properties of aggregates - Part 1: Determination of the resistance to wear (micro-Deval)
EN 12273:2008 Slurry surfacing - Requirements
EN 13055-1:2002/AC:2004 LIGHTWEIGHT AGGREGATES - PART 1: LIGHTWEIGHT AGGREGATES FOR CONCRETE, MORTAR AND GROUT
DIN EN 13075-2:2017-02 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF BREAKING BEHAVIOUR - PART 2: DETERMINATION OF FINES MIXING TIME OF CATIONIC BITUMINOUS EMULSIONS
EN 13450:2002/AC:2004 AGGREGATES FOR RAILWAY BALLAST
EN 12620:2002+A1:2008 Aggregates for concrete
CEN/TS 14243:2010 Materials produced from end of life tyres - Specification of categories based on their dimension(s) and impurities and methods for determining their dimension(s) and impurities
EN 13055-2:2004 Lightweight aggregates - Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications
EN 13383-2:2013 Armourstone - Part 2: Test methods
EN 13139:2002/AC:2004 AGGREGATES FOR MORTAR
EN 12767:2007 Passive safety of support structures for road equipment - Requirements, classification and test methods
EN 12697-2:2015 BITUMINOUS MIXTURES - TEST METHODS - PART 2: DETERMINATION OF PARTICLE SIZE DISTRIBUTION
EN 13043:2002/AC:2004 AGGREGATES FOR BITUMINOUS MIXTURES AND SURFACE TREATMENTS FOR ROADS, AIRFIELDS AND OTHER TRAFFICKED AREAS
EN 13108-20:2016 Bituminous mixtures - Material specifications - Part 20: Type Testing
EN 13286-4:2003 UNBOUND AND HYDRAULICALLY BOUND MIXTURES - TEST METHODS FOR LABORATORY REFERENCE DENSITY AND WATER CONTENT - PART 4: VIBRATING HAMMER
EN 1097-9:2014 Tests for mechanical and physical properties of aggregates - Part 9: Determination of the resistance to wear by abrasion from studded tyres - Nordic test
EN 12274-7 : 2005 Slurry surfacing - Test methods - Part 7: Shaking abrasion test
ONORM EN 14487-1 : 2006 SPRAYED CONCRETE - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY
UNE-EN 13285:2010 Unbound mixtures - Specifications
17/30365077 DC : 0 BS EN 14243-3 - MATERIALS OBTAINED FROM END OF LIFE TYRES - PART 3: SHREDS, CUTS AND CHIPS - METHODS FOR DETERMINING THEIR DIMENSION(S) INCLUDING PROTRUDING FILAMENTS DIMENSIONS
DIN EN 15599-1 E : 2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
I.S. EN 16025-1:2013 THERMAL AND/OR SOUND INSULATING PRODUCTS IN BUILDING CONSTRUCTION - BOUND EPS BALLASTINGS - PART 1: REQUIREMENTS FOR FACTORY PREMIXED EPS DRY PLASTER
I.S. EN 14227-12:2006 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 12: SOIL TREATED BY SLAG
04/30077125 DC : 0 EN 933-11 - TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 11: CLASSIFICATION TEST FOR THE CONSTITUENTS OF COARSE RECYCLED AGGREGATES
I.S. EN 13055-2:2004 LIGHTWEIGHT AGGREGATES - PART 2: LIGHTWEIGHT AGGREGATES FOR BITUMINOUS MIXTURES AND SURFACE TREATMENTS AND FOR UNBOUND AND BOUND APPLICATIONS
PREN 16236 : DRAFT 2015 EVALUATION OF CONFORMITY OF AGGREGATES - INITIAL TYPE TESTING AND FACTORY PRODUCTION CONTROL
I.S. EN 14227-13:2006 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 13: SOIL TREATED BY HYDRAULIC ROAD BINDER
DIN EN 15564 E : 2009 PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS
15/30311097 DC : 0 BS EN 13450 - AGGREGATES FOR RAILWAY BALLAST
PREN 1317-5 : DRAFT 2013 ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS, TEST AND ASSESSMENT METHODS AND ACCEPTANCE CRITERIA
12/30256420 DC : 0 BS EN 15732 - LIGHT WEIGHT FILL AND THERMAL INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS (CEA) - EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA)
11/30240498 DC : 0 BS EN 14227-2 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 2: SLAG BOUND MIXTURES
PREN 1176-1 : DRAFT 2014 PLAYGROUND EQUIPMENT AND SURFACING - PART 1: GENERAL SAFETY REQUIREMENTS AND TEST METHODS
11/30240495 DC : 0 BS EN 14227-5 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND MIXTURES
DIN EN 16025-1:2013-07 THERMAL AND/OR SOUND INSULATING PRODUCTS IN BUILDING CONSTRUCTION - BOUND EPS BALLASTINGS - PART 1: REQUIREMENTS FOR FACTORY PREMIXED EPS DRY PLASTER
12/30256925 DC : 0 BS EN 13055 - LIGHTWEIGHT AGGREGATES FOR CONCRETE, MORTAR, GROUT, BITUMINOUS MIXTURES, SURFACE TREATMENTS AND FOR UNBOUND AND BOUND APPLICATIONS
BS EN 16025-1:2013 Thermal and/or sound insulating products in building construction. Bound EPS ballastings Requirements for factory premixed EPS dry plaster
09/30195711 DC : 0 BS EN 13383-2 - ARMOURSTONE - PART 2: TEST METHODS
10/30218985 DC : DRAFT JUNE 2010 BS EN 13369 - COMMON RULES FOR PRECAST CONCRETE PRODUCTS
PREN 15600-1 : DRAFT 2009 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
I.S. EN ISO 10722:2007 GEOSYNTHETICS - INDEX TEST PROCEDURE FOR THE EVALUATION OF MECHANICAL DAMAGE UNDER REPEATED LOADING - DAMAGE CAUSED BY GRANULAR MATERIAL
PREN 12620 : DRAFT 2015 AGGREGATES FOR CONCRETE
PREN 15732 : DRAFT 2012 LIGHT WEIGHT FILL AND THERMAL INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS (CEA) - EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA)
DIN 4226-2:2002-02 AGGREGATES FOR CONCRETE AND MORTAR - PART 2: LIGHTWEIGHT AGGREGATES
18/30368690 DC : 0 BS EN 13108-31 - BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS - PART 31: ASPHALT CONCRETE WITH BITUMINOUS EMULSION
I.S. EN 13055:2016 LIGHTWEIGHT AGGREGATES
PREN 15330-1 : DRAFT 2013 SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 1: SPECIFICATION FOR SYNTHETIC TURF SURFACES FOR FOOTBALL, HOCKEY, RUGBY UNION TRAINING, TENNIS AND MULTI-SPORTS USE
I.S. EN 15600-1:2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
I.S. EN 14227-15:2015 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
I.S. EN 12767:2007 PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS, CLASSIFICATION AND TEST METHODS
DIN EN 933-5:2005-02 Tests for geometrical properties of aggregates - Part 5: Determination of percentage of crushed and broken surfaces in coarse aggregate particles (including amendment A1:2004)
DIN EN 13075-2:2015-04 (Draft) BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF BREAKING BEHAVIOUR - PART 2: DETERMINATION OF FINES MIXING TIME OF CATIONIC BITUMINOUS EMULSIONS
DIN EN 14487-1:2006-03 Sprayed concrete - Part 1: Definitions, specifications and conformity
EN 13286-2:2010/AC:2012 UNBOUND AND HYDRAULICALLY BOUND MIXTURES - PART 2: TEST METHODS FOR LABORATORY REFERENCE DENSITY AND WATER CONTENT - PROCTOR COMPACTION
DIN EN 12767:2008-01 PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS, CLASSIFICATION AND TEST METHODS
DIN EN 12697-1 E : 2012 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT
DIN EN 14227-2:2013-08 Hydraulically bound mixtures - Specifications - Part 2: Slag bound granular mixtures; German version EN 14227-2:2013
BS EN 13055-2:2004 Lightweight aggregates Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications
BS EN 14317-1:2004 Thermal insulation products for buildings. In-situ thermal insulation formed from exfoliated vermiculite (EV) products Specification for bonded and loose-fill products before installation
BS EN 14316-1:2004 Thermal insulation products for buildings. In-situ thermal insulation formed from expanded perlite (EP) products Specification for bonded and loose-fill products before installation
BS EN 933-3:2012 Tests for geometrical properties of aggregates Determination of particle shape. Flakiness index
I.S. EN 13075-2:2016 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF BREAKING BEHAVIOUR - PART 2: DETERMINATION OF FINES MIXING TIME OF CATIONIC BITUMINOUS EMULSIONS
I.S. EN 13075-1:2016 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF BREAKING BEHAVIOUR - PART 1: DETERMINATION OF BREAKING VALUE OF CATIONIC BITUMINOUS EMULSIONS, MINERAL FILLER METHOD
I.S. EN 932-5:2012 TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5 - COMMON EQUIPMENT AND CALIBRATION
I.S. EN 14227-2:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 2: SLAG BOUND MIXTURES
I.S. EN 13450:2013 AGGREGATES FOR RAILWAY BALLAST
DIN EN 13294:2002-09 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - DETERMINATION OF STIFFENING TIME
I.S. EN 13108-20:2016 BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS - PART 20: TYPE TESTING
I.S. EN 14227-5:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND GRANULAR MIXTURES
DIN EN ISO 10722:2007-08 GEOSYNTHETICS - INDEX TEST PROCEDURE FOR THE EVALUATION OF MECHANICAL DAMAGE UNDER REPEATED LOADING - DAMAGE CAUSED BY GRANULAR MATERIAL
I.S. EN 933-3:2012 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 3: DETERMINATION OF PARTICLE SHAPE - FLAKINESS INDEX
I.S. EN 13286-2:2010 UNBOUND AND HYDRAULICALLY BOUND MIXTURES - PART 2: TEST METHODS FOR LABORATORY REFERENCE DENSITY AND WATER CONTENT - PROCTOR COMPACTION
I.S. EN 933-8:2012 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 8: ASSESSMENT OF FINES - SAND EQUIVALENT TEST
I.S. EN 933-4:2008 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 4: DETERMINATION OF PARTICLE SHAPE - SHAPE INDEX
I.S. EN 1097-9:2014 TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 9: DETERMINATION OF THE RESISTANCE TO WEAR BY ABRASION FROM STUDDED TYRES - NORDIC TEST
I.S. EN 14227-3:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND GRANULAR MIXTURES
DIN EN 206-1:2001-07 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
I.S. EN 933-5:1998 TERMS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - DETERMINATION OF PERCENTAGE OF CRUSHED AND BROKEN SURFACES IN COARSE AGGREGATE PARTICLES
I.S. EN 14487-1:2005 SPRAYED CONCRETE - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY
DIN EN 16630:2015-06 PERMANENTLY INSTALLED OUTDOOR FITNESS EQUIPMENT - SAFETY REQUIREMENTS AND TEST METHODS
13/30282505 DC : 0 BS EN 16630 - PERMANENTLY INSTALLED OUTDOOR FITNESS EQUIPMENT - SAFETY REQUIREMENTS AND TEST METHODS
BS EN 13055:2016 Lightweight aggregates
07/30155111 DC : 0 BS EN 15330-2 - SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 2: SPECIFICATION FOR NEEDLE-PUNCHED SURFACES
DIN EN 1744-8:2012-11 Tests for chemical properties of aggregates - Part 8: Sorting test to determine metal content of Municipal Incinerator Bottom Ash (MIBA) Aggregates
BS EN 15599-1:2010 Thermal insulation products for building equipment and industrial installations. In-situ thermal insulation formed from expanded perlite (EP) products Specification for bonded and loose-fill products before installation
15/30311103 DC : 0 BS EN 13242 - AGGREGATES FOR UNBOUND AND HYDRAULICALLY BOUND MATERIALS FOR USE IN CIVIL ENGINEERING WORK AND ROAD CONSTRUCTION
13/30262917 DC : 0 BS EN 15330-1 - SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 1: SPECIFICATION FOR SYNTHETIC TURF SURFACES FOR FOOTBALL, HOCKEY, RUGBY UNION TRAINING, TENNIS AND MULTI-SPORTS USE
BS EN 16630:2015 Permanently installed outdoor fitness equipment. Safety requirements and test methods
I.S. EN 206-1:2002 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY (INCLUDING IRISH NATIONAL ANNEX)
I.S. EN 13055-1:2002 LIGHTWEIGHT AGGREGATES - PART 1: LIGHTWEIGHT AGGREGATES FOR CONCRETE, MORTAR AND GROUT
DIN EN 15599-1:2010-12 Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation
UNI EN 15599-1 : 2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
UNI EN 15564 : 2009 PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS
03/107772 DC : DRAFT MAY 2003 EN 12697-42 - BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 42: AMOUNT OF FOREIGN MATTERS IN RECLAIMED ASPHALT
DIN 1045-4:2012-02 Concrete, reinforced and prestressed concrete structures - Part 4: Additional rules for the production and the conformity of prefabricated elements
04/30111539 DC : DRAFT JULY 2004 EN 14227-10 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 10: SOIL CEMENT AND CEMENT STABILISED SOILS
BS EN 1367-6:2008 Tests for thermal and weathering properties of aggregates Determination of resistance to freezing and thawing in the presence of salt (NaCl)
DD CEN/TS 14243:2010 Materials produced from end of life tyres. Specification of categories based on their dimension(s) and impurities and methods for determining their dimension(s) and impurities
11/30240501 DC : 0 BS EN 14227-3 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND MIXTURES
S.R. CEN/TS 16637-3:2016 CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PART 3: HORIZONTAL UP-FLOW PERCOLATION TEST
XP CEN/TS 14243 : 2010 XP MATERIALS PRODUCED FROM END OF LIFE TYRES - SPECIFICATION OF CATEGORIES BASED ON THEIR DIMENSION(S) AND IMPURITIES AND METHODS FOR DETERMINING THEIR DIMENSION(S) AND IMPURITIES
I.S. EN 15732:2012 LIGHT WEIGHT FILL AND THERMAL INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS (CEA) - EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA)
UNE-EN 14227-15:2017 Hydraulically bound mixtures - Specifications - Part 15: Hydraulically stabilized soils
PREN 15599-1 : DRAFT 2009 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
NF EN 13285 : 2010 UNBOUND MIXTURES - SPECIFICATION
UNI EN ISO 10722 : 2007 GEOSYNTHETICS - INDEX TEST PROCEDURE FOR THE EVALUATION OF MECHANICAL DAMAGE UNDER REPEATED LOADING - DAMAGE CAUSED BY GRANULAR MATERIAL
15/30310344 DC : 0 BS EN 12620 - AGGREGATES FOR CONCRETE
UNI EN 16025-1 : 2013 THERMAL AND/OR SOUND INSULATING PRODUCTS IN BUILDING CONSTRUCTION - BOUND EPS BALLASTINGS - PART 1: REQUIREMENTS FOR FACTORY PREMIXED EPS DRY PLASTER
PREN 14227-3 : DRAFT 2011 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND MIXTURES
BS EN 1177:2018 Impact attenuating playground surfacing. Methods of test for determination of impact attenuation
EN 1176-1:2017 Playground equipment and surfacing - Part 1: General safety requirements and test methods
DIN EN 932-5:2012-05 Tests for general properties of aggregates - Part 5: Common equipment and calibration
DIN EN 933-3:2012-04 Tests for geometrical properties of aggregates - Part 3: Determination of particle shape - Flakiness index
DIN EN 1097-1:2011-04 Tests for mechanical and physical properties of aggregates - Part 1: Determination of the resistance to wear (micro-Deval)
UNE-EN 13286-2:2011 Unbound and hydraulically bound mixtures - Part 2: Test methods for laboratory reference density and water content - Proctor compaction
DIN EN 12274-7:2005-08 SLURRY SURFACING - PART 7: SHAKING ABRASION TEST
DIN EN 14317-1 E : 2004 THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
BS EN 14227-14:2006 Hydraulically bound mixtures. Specifications Soil treated by fly ash
BS EN 13383-2:2013 Armourstone Test methods
BS EN 14227-5:2013 Hydraulically bound mixtures. Specifications Hydraulic road binder bound granular mixtures
BS EN 13286-4:2003 Unbound and hydraulically bound mixtures Test methods for laboratory reference density and water content. Vibrating hammer
EEMUA 207 : 2009 DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION
UNE-CEN/TS 14243:2012 EX Materials produced from end of life tyres - Specification of categories based on their dimension(s) and impurities and methods for determining their dimension(s) and impurities
I.S. EN 12697-15:2003 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 15: DETERMINATION OF THE SEGREGATION SENSITIVITY
UNI EN 15330-1 : 2013 SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 1: SPECIFICATION FOR SYNTHETIC TURF SURFACES FOR FOOTBALL, HOCKEY, RUGBY UNION TRAINING, TENNIS AND MULTI-SPORTS USE
UNI CEN/TS 14243 : 2010 MATERIALS PRODUCED FROM END OF LIFE TYRES - SPECIFICATION OF CATEGORIES BASED ON THEIR DIMENSION(S) AND IMPURITIES AND METHODS FOR DETERMINING THEIR DIMENSION(S) AND IMPURITIES
UNI EN 14063-1 : 2005 THERMAL INSULATION MATERIALS AND PRODUCTS - IN-SITU FORMED EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA) - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION
UNI EN 933-3 : 2012 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 3: DETERMINATION OF PARTICLE SHAPE - FLAKINESS INDEX
UNI EN 13139 : 2013 AGGREGATES FOR MORTAR
UNI EN 13242 : 2013 AGGREGATES FOR UNBOUND AND HYDRAULICALLY BOUND MATERIALS FOR USE IN CIVIL ENGINEERING WORK AND ROAD CONSTRUCTION
UNI EN 12274-7 : 2005 SLURRY SURFACING - TEST METHODS - PART 7: SHAKING ABRASION TEST
UNI EN 933-4 : 2008 TEST FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 4: DETERMINATION OF PARTICLE SHAPE - SHAPE INDEX
UNI EN 14227-3 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND GRANULAR MIXTURES
I.S. EN 13043:2013 AGGREGATES FOR BITUMINOUS MIXTURES AND SURFACE TREATMENTS FOR ROADS, AIRFIELDS AND OTHER TRAFFICKED AREAS
UNI EN 13043 : 2013 AGGREGATES FOR BITUMINOUS MIXTURES AND SURFACE TREATMENTS FOR ROADS, AIRFIELDS AND OTHER TRAFFICKED AREAS
UNI EN 1097-1 : 2011 TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 1: DETERMINATION OF THE RESISTANCE TO WEAR (MICRO-DEVAL)
EN 14487-1:2005 Sprayed concrete - Part 1: Definitions, specifications and conformity
UNI EN 932-5 : 2012 TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION
UNI EN 1097-9 : 2014 TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 9: DETERMINATION OF THE RESISTANCE TO WEAR BY ABRASION FROM STUDDED TYRES - NORDIC TEST
UNI EN 14227-2 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 2: SLAG BOUND GRANULAR MIXTURES
UNI EN 14227-1 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
UNI EN 13286-2 : 2010 UNBOUND AND HYDRAULICALLY BOUND MIXTURES - PART 2: TEST METHODS FOR LABORATORY REFERENCE DENSITY AND WATER CONTENT - PROCTOR COMPACTION
UNI EN 13383-2 : 2013 ARMOURSTONE - PART 2: TEST METHODS
UNI EN 14227-5 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND GRANULAR MIXTURES
UNI EN 12620 : 2013 AGGREGATES FOR CONCRETE
UNI EN 13450 : 2013 AGGREGATES FOR RAILWAY BALLAST
DIN EN 15600-1 E : 2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
DIN EN 14227-15 E : 2016 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
PD CEN/TS 16637-3:2016 Construction products. Assessment of release of dangerous substances Horizontal up-flow percolation test
UNI EN 1177 : 2008 IMPACT ATTENUATING PLAYGROUND SURFACING - DETERMINATION OF CRITICAL FALL HEIGHT
14/30294810 DC : 0 BS EN 14227-15 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
14/30299480 DC : 0 BS EN 1176-1 - PLAYGROUND EQUIPMENT AND SURFACING - PART 1: GENERAL SAFETY REQUIREMENTS AND TEST METHODS
I.S. EN 14227-14:2006 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 14: SOIL TREATED BY FLY ASH
07/30170936 DC : 0 BS EN 15732 - LIGHT WEIGHT FILL AND THERMAL INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS (CEA) - EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA)
DIN EN 16630 E : 2015 PERMANENTLY INSTALLED OUTDOOR FITNESS EQUIPMENT - SAFETY REQUIREMENTS AND TEST METHODS
11/30240489 DC : 0 BS EN 14227-1 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
09/30207815 DC : 0 BS EN 15599-1 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
06/30149762 DC : 0 EN 12273 - SLURRY SURFACING - SPECIFICATIONS
DIN EN 14227-15:2016-02 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
DIN EN 12273:2008-08 Slurry surfacing - Requirements
DIN EN 12697-2:2015-07 BITUMINOUS MIXTURES - TEST METHODS - PART 2: DETERMINATION OF PARTICLE SIZE DISTRIBUTION
PREN 13139 : DRAFT 2015 AGGREGATES FOR MORTAR
09/30205556 DC : 0 BS EN 932-5 - TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION
PREN 1177 : DRAFT 2016 IMPACT ATTENUATING PLAYGROUND SURFACING - METHODS OF TEST FOR DETERMINATION OF IMPACT ATTENUATION
14/30303776 DC : 0 BS EN 13285 - UNBOUND MIXTURES - SPECIFICATIONS
BS EN 1744-8:2012 Tests for chemical properties of aggregates Sorting test to determine metal content of Municipal Incinerator Bottom Ash (MIBA) Aggregates
EN 1177:2018 Impact attenuating playground surfacing - Methods of test for determination of impact attenuation
NF EN 15600-1 : 2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
I.S. EN 1176-1:2017 PLAYGROUND EQUIPMENT AND SURFACING - PART 1: GENERAL SAFETY REQUIREMENTS AND TEST METHODS
07/30165774 DC : DRAFT AUG 2007 BS EN 933-4 - TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 4: DETERMINATION OF PARTICLE SHAPE - SHAPE INDEX
NF EN 15599-1 : 2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
PREN 13043 : DRAFT 2015 AGGREGATES FOR BITUMINOUS MIXTURES AND SURFACE TREATMENTS FOR ROADS, AIRFIELDS AND OTHER TRAFFICKED AREAS
I.S. EN 12697-2:2015 BITUMINOUS MIXTURES - TEST METHODS - PART 2: DETERMINATION OF PARTICLE SIZE DISTRIBUTION
15/30311106 DC : 0 BS EN 16236 - EVALUATION OF CONFORMITY OF AGGREGATES - INITIAL TYPE TESTING AND FACTORY PRODUCTION CONTROL
13/30286641 DC : 0 BS EN 12767 - PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS AND TEST METHODS
18/30368675 DC : 0 BS EN 1097-2 - TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 2: METHODS FOR THE DETERMINATION OF RESISTANCE TO FRAGMENTATION
PREN 14243-2 : DRAFT 2017 MATERIALS OBTAINED FROM END OF LIFE TYRES - PART 2: GRANULATES AND POWDERS - METHODS FOR DETERMINING THEIR DIMENSION(S) AND IMPURITIES, INCLUDING FREE STEEL AND FREE TEXTILE CONTENT
I.S. EN 15564:2008 PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS
17/30365074 DC : 0 BS EN 14243-2 - MATERIALS OBTAINED FROM END OF LIFE TYRES - PART 2: GRANULATES AND POWDERS - METHODS FOR DETERMINING THEIR DIMENSION(S) AND IMPURITIES, INCLUDING FREE STEEL AND FREE TEXTILE CONTENT
PREN 13242 : DRAFT 2015 AGGREGATES FOR UNBOUND AND HYDRAULICALLY BOUND MATERIALS FOR USE IN CIVIL ENGINEERING WORK AND ROAD CONSTRUCTION
PREN 14227-1 : DRAFT 2011 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
I.S. CWA 14243:2002 POST-CONSUMER TYRE MATERIALS AND APPLICATIONS
DIN EN 933-4:2015-01 Tests for geometrical properties of aggregates - Part 4: Determination of particle shape - Shape index
DIN EN 1097-2:2016-07 (Draft) TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 2: METHODS FOR THE DETERMINATION OF RESISTANCE TO FRAGMENTATION
DIN EN 14063-1:2016-10 (Draft) Thermal insulation products for buildings - In-situ formed expanded clay lightweight aggregate products - Part 1: Specification for the loose-fill products before installation; German and English version prEN 14063-1:2016
DIN EN 1097-9:2014-03 TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 9: DETERMINATION OF THE RESISTANCE TO WEAR BY ABRASION FROM STUDDED TYRES - NORDIC TEST
BS EN 12274-7:2005 Slurry surfacing. Test methods Shaking abrasion test
BS EN 14487-1:2005 Sprayed concrete Definitions, specifications and conformity
ISO 10722:2007 Geosynthetics Index test procedure for the evaluation of mechanical damage under repeated loading Damage caused by granular material
I.S. EN 1097-2:2010 TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 2: METHODS FOR THE DETERMINATION OF RESISTANCE TO FRAGMENTATION
BS EN 13286-2:2010 Unbound and hydraulically bound mixtures Test methods for laboratory reference density and water content. Proctor compaction
BS EN 12192-1:2002 Products and systems for the protection and repair of concrete structures. Granulometry analysis Test method for dry components of premixed mortar
BS EN 14227-12:2006 Hydraulically bound mixtures. Specifications. Soil treated by slag
BS EN 933-4:2008 Tests for geometrical properties of aggregates Determination of particle shape. Shape index
BS EN 14227-2:2013 Hydraulically bound mixtures. Specifications Slag bound granular mixtures
BS EN 12620:2013 Aggregates for concrete
BS EN 932-5:2012 Tests for general properties of aggregates Common equipment and calibration
BS EN 206-1:2000 Concrete Specification, performance, production and conformity
UNE-EN 933-3:2012 Tests for geometrical properties of aggregates - Part 3: Determination of particle shape - Flakiness index
BS EN 12697-15:2003 Bituminous mixtures. Test methods for hot mix asphalt Determination of the segregation sensitivity
BS EN 14227-3:2013 Hydraulically bound mixtures. Specifications Fly ash bound granular mixtures
UNI EN 1097-2 : 2010 TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 2: METHODS FOR THE DETERMINATION OF RESISTANCE TO FRAGMENTATION
BS EN 13139:2013 Aggregates for mortar
UNE-EN 12697-1:2013 Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content
UNE-EN 932-5:2012 Tests for general properties of aggregates - Part 5: Common equipment and calibration
UNE-EN 14227-2:2014 Hydraulically bound mixtures - Specifications - Part 2: Slag bound granular mixtures
UNE-EN 14227-1:2014 Hydraulically bound mixtures - Specifications - Part 1: Cement bound granular mixtures
BS EN 13055-1:2002 Lightweight aggregates Lightweight aggregates for concrete, mortar and grout
UNE-EN 14227-3:2014 Hydraulically bound mixtures - Specifications - Part 3: Fly ash bound granular mixtures
BS EN 933-5:1998 Tests for geometrical properties of aggregates Determination of percentage of crushed and broken surfaces in coarse aggregate particles
ISO/TR 10722-1:1998 Geotextiles and geotextile-related products — Procedure for simulating damage during installation — Part 1: Installation in granular materials
BS EN 14227-10:2006 Hydraulically bound mixtures. Specifications Soil treated by cement
UNI EN 12697-1 : 2012 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT
BS EN 12697-1:2012 Bituminous mixtures. Test methods for hot mix asphalt Soluble binder content
UNE-EN 13075-2:2017 Bitumen and bituminous binders - Determination of breaking behaviour - Part 2: Determination of fines mixing time of cationic bituminous emulsions
UNE-EN 12697-2:2015 Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution
BS EN 13108-20:2016 Bituminous mixtures. Material specifications Type Testing
BS EN 15330-1:2013 Surfaces for sports areas. Synthetic turf and needle-punched surfaces primarily designed for outdoor use Specification for synthetic turf surfaces for football, hockey, rugby union training, tennis and multi-sports use
BS EN 1097-2:2010 Tests for mechanical and physical properties of aggregates Methods for the determination of resistance to fragmentation
BS EN 13108-8:2016 Bituminous mixtures. Material specifications Reclaimed asphalt
I.S. EN 12697-1:2012 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT
BS EN 933-8 : 2012 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 8: ASSESSMENT OF FINES - SAND EQUIVALENT TEST
UNE-EN 13075-1:2017 Bitumen and bituminous binders - Determination of breaking behaviour - Part 1: Determination of breaking value of cationic bituminous emulsions, mineral filler method
BS EN 14227-1:2013 Hydraulically bound mixtures. Specifications Cement bound granular mixtures
UNE-EN 1097-1:2011 Tests for mechanical and physical properties of aggregates - Part 1: Determination of the resistance to wear (micro-Deval)
EN 15330-1:2013 Surfaces for sports areas - Synthetic turf and needle-punched surfaces primarily designed for outdoor use - Part 1: Specification for synthetic turf surfaces for football, hockey, rugby union training, tennis and multi-sports use
EN 1367-6:2008 Tests for thermal and weathering properties of aggregates - Part 6: Determination of resistance to freezing and thawing in the presence of salt (NaCl)
EN 14227-10:2006 Hydraulically bound mixtures - Specifications - Part 10: Soil treated by cement
EN 14063-1:2004/AC:2006 THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION
EN 933-5:1998/A1:2004 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 5: DETERMINATION OF PERCENTAGE OF CRUSHED AND BROKEN SURFACES IN COARSE AGGREGATE PARTICLES
EN 933-7:1998 Tests for geometrical properties of aggregates - Part 7: Determination of shell content - Percentage of shells in coarse aggregates
EN 14317-1:2004 Thermal insulation products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation
EN 14316-1:2004 Thermal insulation products for buildings - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation
EN 14227-3:2013 Hydraulically bound mixtures - Specifications - Part 3: Fly ash bound granular mixtures
EN 16630 : 2015 PERMANENTLY INSTALLED OUTDOOR FITNESS EQUIPMENT - SAFETY REQUIREMENTS AND TEST METHODS
EN 14227-14:2006 Hydraulically bound mixtures - Specifications - Part 14: Soil treated by fly ash
EN 14227-12:2006 Hydraulically bound mixtures - Specifications - Part 12: Soil treated by slag
EN 14227-15 : 2015 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
EN 933-8:2012+A1:2015 Tests for geometrical properties of aggregates - Part 8: Assessment of fines - Sand equivalent test
EN 15600-1:2010 Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation
EN 14227-13:2006 Hydraulically bound mixtures - Specifications - Part 13: Soil treated by hydraulic road binder
EN 15599-1:2010 Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation
EN 932-5:2012/AC:2014 TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION
EN 933-4:2008 Tests for geometrical properties of aggregates - Part 4: Determination of particle shape - Shape index
EN 15732:2012 Light weight fill and thermal insulation products for civil engineering applications (CEA) - Expanded clay lightweight aggregate products (LWA)
EN 14227-5:2013 Hydraulically bound mixtures - Specifications - Part 5: Hydraulic road binder bound granular mixtures
EN 1744-3:2002 Tests for chemical properties of aggregates - Part 3: Preparation of eluates by leaching of aggregates
EN 1367-3:2001/AC:2004 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 3: BOILING TEST FOR "SONNENBRAND BASALT"
EN 15564:2008 Precast concrete products - Resin bound concrete - Requirements and test methods
EN 933-3:2012 Tests for geometrical properties of aggregates - Part 3: Determination of particle shape - Flakiness index
EN 206-1:2000/A2:2005 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
EN 16025-1:2013 Thermal and/or sound insulating products in building construction - Bound EPS ballastings - Part 1: Requirements for factory premixed EPS dry plaster
EN 14227-1:2013 Hydraulically bound mixtures - Specifications - Part 1: Cement bound granular mixtures
EN 1744-8:2012 Tests for chemical properties of aggregates - Part 8: Sorting test to determine metal content of Municipal Incinerator Bottom Ash (MIBA) Aggregates
EN 14227-2:2013 Hydraulically bound mixtures - Specifications - Part 2: Slag bound granular mixtures
DIN EN 1744-8 E : 2012 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 8: SORTING TEST TO DETERMINE METAL CONTENT OF MUNICIPAL INCINERATOR BOTTOM ASH (MIBA) AGGREGATES
UNE-EN 15732:2014 Light weight fill and thermal insulation products for civil engineering applications (CEA) - Expanded clay lightweight aggregate products (LWA)
06/30158376 DC : 0 BS EN 15599-1 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
BS EN 15564:2008 Precast concrete products. Resin bound concrete. Requirements and test methods
13/30278735 DC : 0 BS EN 13108-20 - BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS - PART 20: TYPE TESTING
DIN EN 1367-6:2008-12 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 6: DETERMINATION OF RESISTANCE TO FREEZING AND THAWING IN THE PRESENCE OF SALT (NACL)
DIN EN 15564:2009-05 PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS
DIN 4226-1:2001-07 AGGREGATES FOR CONCRETE AND MORTAR - PART 1: NORMAL AND HEAVY-WEIGHT AGGREGATES
17/30345777 DC : 0 BS EN 13383-2 - ARMOURSTONE - PART 2: TEST METHODS
I.S. EN 14227-10:2006 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 10: SOIL TREATED BY CEMENT
BS EN ISO 10722:2007 Geosynthetics. Index test procedure for the evaluation of mechanical damage under repeated loading. Damage caused by granular material
16/30320762 DC : 0 BS EN 1097-2 - TESTS FOR MECHANICAL AND PHYSICAL PROPERTIES OF AGGREGATES - PART 2: METHODS FOR THE DETERMINATION OF RESISTANCE TO FRAGMENTATION
UNE-EN 1744-8:2013 Tests for chemical properties of aggregates - Part 8: Sorting test to determine metal content of Municipal Incinerator Bottom Ash (MIBA) Aggregates
16/30336446 DC : 0 BS EN 1177 - IMPACT ATTENUATING PLAYGROUND SURFACING - METHODS OF TEST FOR DETERMINATION OF IMPACT ATTENUATION
06/30158382 DC : 0 BS EN 15600-1 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULATE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
PREN 14227-5 : DRAFT 2011 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND MIXTURES
12/30257889 DC : 0 BS EN 206 - CONCRETE - SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
UNE-EN 16025-1:2016 Thermal and/or sound insulating products in building construction - Bound EPS ballastings - Part 1: Requirements for factory premixed EPS dry plaster
BS EN 12697-2:2015 Bituminous mixtures. Test methods Determination of particle size distribution
11/30249131 DC : 0 BS EN 16333 - SLURRY SURFACING - SPECIFICATION FOR AIRFIELDS
I.S. EN 13285:2010 UNBOUND MIXTURES - SPECIFICATIONS
BS EN 12273:2008 Slurry surfacing. Requirements
DIN EN 15732 E : 2013 LIGHT WEIGHT FILL AND THERMAL INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS (CEA) - EXPANDED CLAY LIGHTWEIGHT AGGREGATE PRODUCTS (LWA)
BS EN 15600-1:2010 Thermal insulation products for building equipment and industrial installations. In-situ thermal insulation formed from exfoliated vermiculite (EV) products Specification for bonded and loose-fill products before installation
UNE-EN 16630:2015 Permanently installed outdoor fitness equipment - Safety requirements and test methods
02/101686 DC : DRAFT FEB 2002 PREN 14317-1 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
UNI EN 1367-6 : 2008 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 6: DETERMINATION OF RESISTANCE TO FREEZING AND THAWING IN THE PRESENCE OF SALT (NACL)
15/30311094 DC : 0 BS EN 13139 - AGGREGATES FOR MORTAR
I.S. EN 16630:2015 PERMANENTLY INSTALLED OUTDOOR FITNESS EQUIPMENT - SAFETY REQUIREMENTS AND TEST METHODS
UNI EN 1744-8 : 2012 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 8: SORTING TEST TO DETERMINE METAL CONTENT OF MUNICIPAL INCINERATOR BOTTOM ASH (MIBA) AGGREGATES
I.S. EN 15599-1:2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXPANDED PERLITE (EP) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
I.S. EN 1177:2018 IMPACT ATTENUATING PLAYGROUND SURFACING - METHODS OF TEST FOR DETERMINATION OF IMPACT ATTENUATION
PREN 13108-31 : DRAFT 2018 BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS - PART 31: ASPHALT CONCRETE WITH BITUMINOUS EMULSION
UNI EN 15600-1 : 2010 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
DIN EN 13285:2010-12 UNBOUND MIXTURES - SPECIFICATIONS
EN 13285:2010 Unbound mixtures - Specifications
NF EN 12767 : 2011 PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS, CLASSIFICATION AND TEST METHODS
DIN EN 15330-1:2013-12 SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 1: SPECIFICATION FOR SYNTHETIC TURF SURFACES FOR FOOTBALL, HOCKEY, RUGBY UNION TRAINING, TENNIS AND MULTI-SPORTS USE
DIN EN 14227-1:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
BS EN 1744-3:2002 Tests for chemical properties of aggregates Preparation of eluates by leaching of aggregates
EN 1097-2:2010 Tests for mechanical and physical properties of aggregates - Part 2: Methods for the determination of resistance to fragmentation
BS EN 12767:2007 Passive safety of support structures for road equipment. Requirements, classification and test methods
BS EN 14063-1:2004 Thermal insulation products for buildings. In-situ formed expanded clay lightweight aggregate products Specification for the loose-fill products before installation
BS EN 933-7:1998 Tests for geometrical properties of aggregates Determination of shell content. Percentage of shells in coarse aggregates
BS EN 13075-2:2016 Bitumen and bituminous binders. Determination of breaking behaviour Determination of fines mixing time of cationic bituminous emulsions
EN 12192-1:2002 Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 1: Test method for dry components of premixed mortar
EN 13055 : 2016 LIGHTWEIGHT AGGREGATES
DIN EN 14227-13:2006-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 13: SOIL TREATED BY HYDRAULIC ROAD BINDER
DIN EN 13055-2:2004-09 LIGHTWEIGHT AGGREGATES - PART 2: LIGHTWEIGHT AGGREGATES FOR BITUMINOUS MIXTURES AND SURFACE TREATMENTS AND FOR UNBOUND AND BOUND APPLICATIONS
DIN EN 13055-1:2002-08 LIGHTWEIGHT AGGREGATES - PART 1: LIGHTWEIGHT AGGREGATES FOR CONCRETE, MORTAR AND GROUT
EN 13242:2002+A1:2007 Aggregates for unbound and hydraulically bound materials for use in civil engineering work and road construction
EN 13075-1:2016 Bitumen and bituminous binders - Determination of breaking behaviour - Part 1: Determination of breaking value of cationic bituminous emulsions, mineral filler method
DIN EN 14063-1:2004-11 Thermal insulation materials and products - In-situ formed expanded clay lightweight aggregate products (LWA) - Part 1: Specification for the loose-fill products before installation; German version EN 14063-1:2004
DIN EN 14227-12:2006-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 12: SOIL TREATED BY SLAG

EN 932-2:1999 Tests for general properties of aggregates - Part 2: Methods for reducing laboratory samples
ISO 3310-1:2016 Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth
ISO 3310-2:2013 Test sieves — Technical requirements and testing — Part 2: Test sieves of perforated metal plate
EN 933-2:1995 Tests for geometrical properties of aggregates - Part 2: Determination of particle size distribution - Test sieves, nominal size of apterures
EN 932-5:2012/AC:2014 TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION
EN 1097-6:2013 Tests for mechanical and physical properties of aggregates - Part 6: Determination of particle density and water absorption

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.