EN ISO 15527:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2010)
13-03-2013
30-06-2019
Foreword
1 Scope
2 Normative references
3 Material
4 Requirements
5 Test methods
6 Designation
7 Marking
Annex A (normative) - Requirements for rectangularity
Annex B (normative) - Determination of abrasion properties
Annex C (informative) - Example of apparatus for the
determination of abrasion properties
ISO 15527:2010 specifies the requirements and test methods for solid flat compression-moulded sheets of polyethylene (PE‑UHMW and PE‑HD) without fillers or reinforcing materials. It applies only to thicknesses from 10 mm to 200 mm.
| Committee |
CEN/TC 249
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS-EN ISO 15527:2018 | Identical |
| NF EN ISO 15527 : 2013 | Identical |
| BS EN ISO 15527:2013 | Identical |
| NS EN ISO 15527 : 2013 | Identical |
| NEN-EN-ISO 15527:2019 en | Identical |
| BS EN ISO 15527:2018 | Identical |
| DIN EN ISO 15527:2013-05 | Identical |
| I.S. EN ISO 15527:2018 | Identical |
| ISO 15527:2010 | Identical |
| NBN EN ISO 15527 : 2013 | Identical |
| PN EN ISO 15527 : 2013 | Identical |
| I.S. EN ISO 15527:2013 | Identical |
| NEN EN ISO 15527 : 2013 | Identical |
| ISO 15527:2018 | Identical |
| UNE-EN ISO 15527:2014 | Identical |
| 16/30317348 DC : 0 | BS EN 15860 - PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| PREN 15860 : DRAFT 2016 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| ISO 11542-2:1998 | Plastics — Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11542-1:2001 | Plastics — Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 291:2008 | Plastics — Standard atmospheres for conditioning and testing |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 1872-1:1993 | Plastics — Polyethylene (PE) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |