I.S. EN 60745-1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS
Hardcopy , PDF
English
15-01-2010
23-11-2021
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 General conditions for the tests
6 Environmental requirements
7 Classification
8 Marking and instructions
9 Protection against access to live parts
10 Starting
11 Input and current
12 Heating
13 Leakage current
14 Moisture resistance
15 Electric strength
16 Overload protection of transformers and associated
circuits
17 Endurance
18 Abnormal operation
19 Mechanical hazards
20 Mechanical strength
21 Construction
22 Internal wiring
23 Components
24 Supply connection and external flexible cords
25 Terminals for external conductors
26 Provision for earthing
27 Screws and connections
28 Creepage distances, clearances and distances through
insulation
29 Resistance to heat, fire and tracking
30 Resistance to rusting
31 Radiation, toxicity and similar hazards
Annex A (normative) - Measurement of creepage distances and
clearances
Annex B (normative) - Motors not isolated from the supply
mains and having basic insulation not designed for
the rated voltage of the tool
Annex F (normative) - Needle-flame test
Annex G (normative) - Proof tracking test
Annex I (normative) - Switches
Annex J (informative) - Selection and sequence of the tests of
Clause 29
Annex K (normative) - Battery tools and battery packs
Annex L (normative) - Battery tools and battery packs
provided with mains connection or non-isolated sources
Annex M (normative) - Safety of working stands for operation
with hand-held motor-operated electric tools
Annex N (informative) - Rules for routine tests
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Annex ZB (informative) - Possible sources of errors during
vibration measurements
Bibliography
Covers the safety of hand-held motor-operated or magnetically driven electric tools, the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools.
| DevelopmentNote |
Supersedes I.S. EN 50260-1. (11/2003) Supersedes I.S. EN 50144-1. (02/2006) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017) 2009 Edition is Partially Superseded by I.S. EN 62841-1. (07/2017)
|
| DocumentType |
Standard
|
| Pages |
309
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 60745-1 : 2010 AMD 11 2011 | Identical |
| NBN EN 60745-1 : 2009 AMD 1 2011 | Identical |
| BS EN 60745-1 : 2009 | Identical |
| EN 60745-1:2009 | Equivalent |
| UNE-EN 60745-1:2010 | Identical |
A newer version of this standard is available.
View Current Edition
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.