SAE USCAR 2 : 2013
|
PERFORMANCE SPECIFICATION FOR AUTOMOTIVE ELECTRICAL CONNECTOR SYSTEMS
|
ISO 16750-2:2012
|
Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 2: Electrical loads
|
ISO 16750-4:2010
|
Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 4: Climatic loads
|
ISO 16750-5:2010
|
Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 5: Chemical loads
|
IEC 60068-2-27:2008
|
Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
|
ISO 16750-1:2006
|
Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 1: General
|
ISO 7637-1:2015
|
Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations
|
TIA/EIA 455-1 : B1998(R2008)
|
CABLE FLEXING FOR FIBER OPTIC INTERCONNECTING DEVICES
|
ISO 11452-4:2011
|
Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 4: Harness excitation methods
|
TIA 455-21 : A1988(R2012)
|
FOTP-21 MATING DURABILITY FOR FIBER OPTIC INTERCONNECTING DEVICES
|
ISO 7637-2:2011
|
Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only
|
IEC 60794-1-2:2017
|
Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance
|
SAE J 1113/12 : 2006
|
ELECTRICAL INTERFERENCE BY CONDUCTION AND COUPLING - CAPACITIVE AND INDUCTIVE COUPLING VIA LINES OTHER THAN SUPPLY LINES
|
SAE J 1113/21 : 2013
|
ELECTROMAGNETIC COMPATIBILITY MEASUREMENT PROCEDURE FOR VEHICLE COMPONENTS - PART 21: IMMUNITY TO ELECTROMAGNETIC FIELDS, 30 MHZ TO 18 GHZ, ABSORBER-LINED CHAMBER
|
ISO 8092-2:2005
|
Road vehicles — Connections for on-board electrical wiring harnesses — Part 2: Definitions, test methods and general performance requirements
|
CISPR 25:2016
|
Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers
|
IEC 61280-1-1:2013
|
Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable
|
ISO 6722:2006
|
Road vehicles 60 V and 600 V single-core cables Dimensions, test methods and requirements
|
IEC 61300-3-8:1995
|
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-8: Examinations and measurements - Ambient light susceptibility
|
ISO 16750-3:2012
|
Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 3: Mechanical loads
|
IEC 60793-1-40:2001
|
Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
|
ISO 175:2010
|
Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
|
IEC 60695-11-10:2013
|
Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
|
SAE USCAR 17 : 2013
|
PERFORMANCE SPECIFICATION FOR AUTOMOTIVE RF CONNECTOR SYSTEMS
|
TIA/EIA 455-34 : A1995(R2002)
|
INTERCONNECTION DEVICE INSERTION LOSS TEST
|
IEC 60068-2-28:1990
|
Environmental testing - Part 2: Tests. Guidance for damp heat tests
|
SAE USCAR 19 : 2002
|
COAXIAL CABLE CONNECTOR INTERFACE - SQUARE OUTER CONDUCTOR
|
SAE USCAR 18 : 2011
|
USCAR-17 SUPPLEMENT
|
ISO 1817:2015
|
Rubber, vulcanized or thermoplastic Determination of the effect of liquids
|