NFPA 1150:2022
Current
The latest, up-to-date edition.
Standard on Foam Chemicals for Fires in Class A Fuels
28-07-2021
Chapter 1 Administration 1.1 Scope. 1.2 Purpose. Chapter 2 Referenced Publications 2.1 General. 2.2 NFPA Publications. (Reserved) 2.3 Other Publications. 2.4 References for Extracts in Mandatory Sections. Chapter 3 Definitions 3.1 General. 3.2 NFPA Official Definitions. 3.3 General Definitions. Chapter 4 Characteristics and Acceptance Requirements 4.1 General. 4.2 Foam Concentrate. 4.3 Foam Solution. 4.4 Foam. 4.5 Labeling and Documentation. Chapter 5 Test Methods 5.1 General. 5.2 Exposure Protection Effectiveness. 5.3 Health, Safety, and Environmental Considerations. 5.4 Physical Properties. 5.5 Corrosion and Materials Compatibility. Chapter 6 ClassA Fire Extinguishment Tests 6.1 General. 6.2 Wood Crib Fire Test. 6.3 Deep-Seated Fire Test. 6.4 Wood Fiberboard Penetration.Annex A Explanatory Material Annex B Informational References
This standard specifies requirements for Class A foam and the chemicals used to produce Class A foam that is used to control, suppress, or prevent fires in Class A fuels.
| DevelopmentNote |
TIA 22-1, Reference: 6.2.1, 6.3.1, 6.3.2, 6.3.3(5), 6.4.1, 6.4.2 and 6.4.3(5), Issued Date 07-Jul-2022
|
| DocumentType |
Standard
|
| ProductNote |
THIS STANDARD ALSO REFERS TO EPA Method 537.1,OPPTS 835.3110,OPPTS 850.1075,OPPTS 870.1100,OPPTS 870.1200,OPPTS 870.2400,OPPTS 870.2500,
|
| PublisherName |
National Fire Protection Association
|
| Status |
Current
|
| Supersedes |
| NFPA 1900:2024 | Standard for Aircraft Rescue and Fireghting Vehicles, Automotive Fire Apparatus, Wildland Fire Apparatus, and Automotive Ambulances |
| NFPA 18A:2022 | Standard on Water Additives for Fire Control and Vapor Mitigation |
| NFPA 11:2024 | Standard for Low-, Medium, and High-Expansion Foam |
| SAE AMSDTL23053/5A | Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Flexible, Crosslinked |
| ASTM D 2281 : 2010 : R2016 | Standard Test Method for Evaluation of Wetting Agents by the Skein Test |
| NACE TM 01 69 : 2012 | Standard Guide for Laboratory Immersion Corrosion Testing of Metals |
| MIL-PRF-81733 Revision D:1998 | Sealing and Coating Compound, Corrosion Inhibitive |
| NFPA 18:2021 | Standard on Wetting Agents |
| A-A-55859 Revision A:2002 | Tube, Nonmetallic; Polyvinyl Chloride (PVC) Flexible (General Use) |
| ASTM E 729 : 1996 : R2014 | Standard Guide for Conducting Acute Toxicity Tests on Test Materials with Fishes, Macroinvertebrates, and Amphibians |
| ASTM D 92 : 2018 | Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester |
| ASTM E 3 : 2011 : R2017 | Standard Guide for Preparation of Metallographic Specimens |
| SAE AMS3208N | Chloroprene (CR) Rubber Weather Resistant 45 - 55 |
| ISO/IEC 17025:2017 | General requirements for the competence of testing and calibration laboratories |
| ASTM D 1331 : 2014 | Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials |
| ASTM E 1321 : 2018 | Standard Test Method for Determining Material Ignition and Flame Spread Properties |
| ASTM D 2196 : 2018 | Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscountess |
| ISO 304:1985 | Surface active agents — Determination of surface tension by drawing up liquid films |
| ASTM D 97 : 2017 : REV B | Standard Test Method for Pour Point of Petroleum Products |
| NFPA 472 : 2018 | STANDARD FOR COMPETENCE OF RESPONDERS TO HAZARDOUS MATERIALS/WEAPONS OF MASS DESTRUCTION INCIDENTS |
| UL 711:8ED 2018-08-06 | Rating and Fire Testing of Fire Extinguishers |
| SAE AMSS8802E | Sealing Compound, Fuel Resistant, Integral Fuel Tanks and Fuel Cell Cavities |
| ASTM E 407 : 2007 : R2015 : EDT 1 | Standard Practice for Microetching Metals and Alloys |
| ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |