VDE 0641-2 : 1984
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MINIATURE CIRCUIT BREAKERS UP TO 63A RATED CURRENT, UP TO 440 V D.C.
12-01-2013
01-07-2002
1 Anwendungsbereich und Zweck
2 Begriffe
3 Allgemeine Anforderungen
4 Allgemeines über Prüfungen
5 Nennwerte
6 Klassifikation
7 Aufschriften
8 Unverwechselbarkeit
9 Berührungsschutz
10 Anschlussklemmen
11 Aufbau
12 Mechanismus
13 Schrauben, stromführende Teile und Verbindungen
14 Wärmebeständigkeit
15 Kriech- und Luftstrecken
16 Oxidationsschutz
17 Feuchtigkeitsbeständigkeit
18 Isolationswiderstand und Spannungsfestigkeit
19 Erwärmung
20 Verhalten im Gebrauch
21 Ein- und Ausschaltvermögen
22 Auslösecharakteristik
23 Einfluss der Umgebungstemperatur auf die
Auslösecharakteristik
24 Widerstandsfähigkeit gegen mechanische Erschütterungen
25 Spannungsfall und Verlustleistung
26 Mechanische Festigkeit
27 Einteilung der LS-Schalter in Strombegrenzungsklassen
28 Zuordnung von Vorsicherungen
AMD NOT YET TRANSLATED
| DocumentType |
Standard
|
| PublisherName |
Verband Deutscher Elektrotechniker
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| DIN VDE 0641-2 : 1984 | Identical |
| DIN 57641-2 : 1984 | Identical |
| DIN 57641-2 : 1984 | Corresponds |
| DIN VDE 0641-3 : 1984 | MINIATURE CIRCUIT BREAKERS UP TO 63 A RATED CURRENT, UP TO 415 V A.C. AND UP TO 440 V D.C |
| DIN 57641-3 : 1984 | MINIATURE CIRCUIT BREAKERS UP TO 63 A RATED CURRENT, UP TO 415 V A.C. AND UP TO 440 V D.C |
| VDE 0641-3 : 1984 | MINIATURE CIRCUIT BREAKERS UP TO 63 A RATED CURRENT, UP TO 415 V A.C. AND UP TO 440 V D.C. |
| DIN 40100-3:1985-07 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT IN THE ELECTROTECHNICAL FIELD; CURRENT, VOLTAGE, FREQUENCY, CONDUCTORS, METHODS OF EARTHING |
| DIN 46282:1973-11 | CLAMPING SADDLE FOR CONDUCTORS |
| DIN 46206-1:1985-06 | TERMINALS FOR ELECTRICAL EQUIPMENT; FLAT BLADE TERMINALS FOR THE CONNECTION OF ROUND COPPER CONDUCTORS UP TO 70 MM[2] |
| DIN 46207:1971-06 | CONNECTIONS FOR ELECTRICAL DEVICES - SLEEVE TERMINALS AND SIDE OPENING SLEEVE TERMINALS - PRINCIPAL DIMENSIONS AND CORRELATION |
| DIN 49500:1980-03 | Miniature circuit breakers, 6 to 25 A, 415 V a.c. and 250 V d.c., screw-in in D-type fuse-bases DII |
| DIN 57636-31 : 1983 | LOW VOLTAGE FUSES - PART 31: D-SYSTEM; PROTECTION OF CABLES AND CORDS UP TO 100 A AND 500 V AND/OR UP TO 63 A 660 V A.C. 600 V D.C. |
| DIN 57470-1 : 1984 | TESTING EQUIPMENT AND TESTING METHODS; TESTING OF PROTECTION AGAINST CONTACT; IEC TESTING FINGER |
| DIN EN 50022:1978-05 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR FOR INDUSTRIAL USE - MOUNTING RAILS, TOP HAT RAILS, 35 MM WIDE, FOR SNAP ON MOUNTING OF EQUIPMENT |
| VDE 0609-1:2000-12 | CONNECTING DEVICES - ELECTRICAL COPPER CONDUCTORS - SAFETY REQUIREMENTS FOR SCREW-TYPE AND SCREWLESS-TYPE CLAMPING UNITS - PART 1: GENERAL REQUIREMENTS AND PARTICULAR REQUIREMENTS FOR CLAMPING UNITS FOR CONDUCTORS FROM 0.2 MM[2] UP TO 35 MM[2] |
| VDE 0470 : 1961 | RULES FOR TESTING EQUIPMENT AND TESTING METHODS |
| DIN 40100-2:1987-08 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT IN THE ELECTROTECHNICAL FIELD; OPERATING, SWITCH POSITION, FUNCTION |
| DIN 46206-2:1971-06 | SUPPLY-TERMINALS FOR ELECTRICAL EQUIPMENT >= 40 A, CONNECTIONS WITH RECTANGULAR CROSS-SECTION, BASIC DIMENSIONS AND COORDINATION |
| DIN 57609-1 : 1983 | SCREW TERMINAL CLAMPING POINTS FOR CONNECTION OF COPPER CONDUCTORS UP TO 240 MM[2]; GENERAL REQUIREMENTS |
| DIN VDE 0636-31:2015-03 | Low-voltage fuses Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) – Examples of standardized systems of fuses A to F – National Supplement 1: Rated voltage = AC 690 V and rated voltage = DC 600 V |
| DIN 46288:1974-08 | CONNECTING WASHERS FOR CONDUCTORS |
| DIN 46289-1:1984-01 | TERMINALS FOR ELECTRICAL PURPOSES; CLASSIFICATION, DEFINITIONS, TECHNICAL TERMS |