EN 728:1997
|
Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
|
EN 1107-2 : 2001
|
Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing
|
EN ISO 527-2:2012
|
Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
|
EN 1542:1999
|
Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off
|
ISO 2039-1:2001
|
Plastics Determination of hardness Part 1: Ball indentation method
|
EN ISO 6259-1:2015
|
Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015)
|
ISO 75-2:2013
|
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
|
EN 13380:2001
|
General requirements for components used for renovation and repair of drain and sewer systems outside buildings
|
CEN/TR 14920:2005
|
Jetting resistance of drain and sewer pipes - Moving jet test method
|
ISO 527-2:2012
|
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
|
ISO 11296-1:2009
|
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
|
ISO 6259-1:2015
|
Thermoplastics pipes Determination of tensile properties Part 1: General test method
|
EN 445:2007
|
Grout for prestressing tendons - Test methods
|
EN 196-1:2016
|
Methods of testing cement - Part 1: Determination of strength
|
EN ISO 75-2:2013
|
Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
|
ISO 4624:2016
|
Paints and varnishes — Pull-off test for adhesion
|
ISO 11296-7:2011
|
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes
|
EN 1979:1999
|
Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam
|
EN ISO 2039-1 : 2003
|
PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD (ISO 2039-1:2001)
|
ISO 1183-1:2012
|
Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
|
EN ISO 4624:2016
|
Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016)
|
EN 206-1:2000/A2:2005
|
CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
|
EN 1015-6:1998/A1:2006
|
METHODS OF TEST FOR MORTAR FOR MASONRY - PART 6: DETERMINATION OF BULK DENSITY OF FRESH MORTAR
|
ISO 10544:1992
|
Cold-reduced steel wire for the reinforcement of concrete and the manufacture of welded fabric
|
EN 1610:2015
|
Construction and testing of drains and sewers
|
EN 1916:2002/AC:2008
|
CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED
|
EN 13067:2012
|
Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies
|
PREN ISO 11296-7 : DRAFT 2012
|
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NONPRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011)
|
EN ISO 1133:2005
|
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
|
ISO 527-3:1995
|
Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
|
EN ISO 527-3:1995/AC:2002
|
PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
|
ISO 1133:2005
|
Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
|
EN 14117:2004
|
Products systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products
|
EN ISO 1183-1:2012
|
Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
|