ASTM F 2648/F2648M : 2017 : REDLINE

Name: ASTM F 2648/F2648M : 2017 : REDLINE
Brand: ASTM
Price: 75.00 USD

Superseded

View Superseded by

Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

Available format(s)

PDF

Superseded date

08-19-2020

Language(s)

English

Published date

12-01-2017

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 08.04, 2018 Defines requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner.

1.1This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 2 to 60 in. [50 to 1500 mm].

1.2The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings suitable for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads.

Note 1:Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based on diameter limitations within the respective standards.

Note 2:Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer applications.

1.3This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1).

(A)Inside Diameters for metric (SI) sizes are in direct Imperial equivalent dimensions

1.4This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5.

1.5Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	F 17
DocumentType	Redline
Pages	9
PublisherName	American Society for Testing and Materials
Status	Superseded
SupersededBy	ASTM F 2648/F2648M : 2020 : REDLINE

MIL-STD-129 Revision R:2014	Military Marking for Shipment and Storage
ASTM D 618 : 2013 : REDLINE	Standard Practice for Conditioning Plastics for Testing
AASHTO LRFD EM : 2007 ERRATA 2007	AASHTO LRFD BRIDGE DESIGN SPECIFICATIONS, CUSTOMARY U.S. UNITS AND AASHTO LRFD BRIDGE DESIGN SPECIFICATIONS, SI UNITS
FED-STD-123 Revision H:2007	MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM D 2444 : 1999	Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 5630 : 2013 : REDLINE	Standard Test Method for Ash Content in Plastics (Withdrawn 2022)
ASTM D 2122 : 2016 : REDLINE	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3350 : 2014 : REDLINE	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 7399 : 2008	Standard Test Method for Determination of the Amount of Polypropylene (PP) in Polypropylene/LDPE Mixtures Using Infrared Spectrophotometer (FTIR) (Withdrawn 2017)
ASTM F 449 : 2016 : REDLINE	Standard Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control