• There are no items in your cart

ASTM D 618 : 2013 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Conditioning Plastics for Testing
Available format(s)

PDF

Superseded date

08-13-2021

Language(s)

English

Published date

07-11-2013

CONTAINED IN VOL. 08.01, 2015 Describes the physical and electrical properties of plastics are influenced by temperature and relative humidity in a manner that materially affects test results.

1.1In general, the physical and electrical properties of plastics are influenced by temperature and relative humidity in a manner that materially affects test results. In order to make reliable comparisons between different materials and between different laboratories, it is necessary to standardize the humidity conditions, as well as the temperature, to which specimens of these materials are subjected prior to and during testing. This practice defines procedures for conditioning plastics (although not necessarily to equilibrium) prior to testing, and the conditions under which they shall be tested.

1.2For some materials, it is possible that a material specification exists that requires the use of this practice, but with some procedural modifications. The material specification takes precedence over this practice. Refer to the material specification before using this practice. Table 1 in Classification D4000 lists the ASTM material specifications that currently exist.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1This standard and ISO 291 address the same subject matter, but differ in technical content. ISO 291 describes only two temperature and humidity conditions for conditioning or testing, or both.

Committee
D 20
DevelopmentNote
Supersedes ASTM D 6054. (12/2012)
DocumentType
Redline
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 2673 : 2014 : REDLINE Standard Specification for Oriented Polypropylene Film
C22.2 NO. 62-93 (R2017) Surface Raceway Systems
ASTM F 636 : 1985 : R1991 Guide for Selection of Tests for Material Properties of Transfer Molding Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996)
ASTM D 2911/D2911M : 2016 : REDLINE Standard Specification for Dimensions and Tolerances for Plastic Bottles
ASTM D 7471 : 2009 : R2014 Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials
ASTM D 7106 : 2005 : R2010 Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes
ASTM F 1987 : 2001 Standard Specification for Multilayer Pipe Type 2 , Compression Fittings, and Compression Joints for Hydronic Heating Systems
ASTM D 5948 : 2005 : R2012 Standard Specification for Molding Compounds, Thermosetting
ASTM D 5436 : 2015 : REDLINE Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes
ASTM D 3894 : 1988 Test Method for Evaluation of Fire Response of Rigid Cellular Plastics Using a Small Corner Configuration (Withdrawn 1994)
ASTM D 3998 : 1981 Test Method for Pendulum-Impace Resistance of Extrusion Plastometer Extrudates (Withdrawn 1989)
ASTM D 2990 : 2017 : REDLINE Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 2308 : 2007 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
MIL-P-24608 Revision A:1987 PIPE, FITTINGS, AND ADHESIVE KITS, GLASS-REINFORCED THERMOSETTING EPOXY RESIN FOR SHIPBOARD PIPING SYSTEMS
CSA S807 : 2010 : R2015 SPECIFICATION FOR FIBRE-REINFORCED POLYMERS
ASTM D 3826 : 1998 : R2008 Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
ASTM D 2466 : 2017 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
ASTM D 6261 : 2014 : REDLINE Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
ASTM D 2295 : 1996 : R2008 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 6778 : 2014 : REDLINE Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)
ASTM F 510 : 1993 : R1999 Standard Test Method for Resistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method
CTI STD 131 : 2009 FIBERGLASS-REINFORCED PLASTIC PANELS
L-P-535 Revision E:1979 PLASTIC SHEET (SHEETING): PLASTIC STRIP: POLY(VINYL CHLORIDE) AND POLY(VINYL CHLORIDE-VINYL ACETATE), RIGID
ASTM D 2683 : 2014 : REDLINE Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
ASTM D 149 : 2009 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
ASTM F 2807 : 2013 Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications
ASTM D 5041 : 1998 : R2004 Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Joints
ASTM D 2293 : 1996 : R2008 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 4225 : 2003 Standard Specification for Styrene-Butadiene Sheeting (Withdrawn 2009)
ASTM F 1505 : 2016 : REDLINE Standard Specification for Insulated and Insulating Hand Tools
CSA Z245.20-Z245.21 : 2006 EXTERNAL FUSION BOND EPOXY COATING FOR STEEL PIPE/EXTERNAL POLYETHYLENE COATING FOR PIPE
ASTM D 4093 : 1995 : R2014 Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials
ASTM D 2741 : 1995 Standard Test Method for Susceptibility of Polyethylene Bottles to Soot Accumulation
ASTM D 2275 : 2014 : REDLINE Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
ASTM D 1457 : 1992 Specification for Polytetrafluorethylene (PTFE) Molding and Extrusion Materials (Withdrawn 1996)
MIL-M-48245 Revision B:1988 MOLDING COMPOUND, HOUSING
ASTM D 5476 : 1999 Standard Classification System for Thermoplastic Polyurethane Materials (TPU) (Withdrawn 2005)
ASTM F 2158 : 2008 : R2016 Standard Specification for Residential Central-Vacuum Tube and Fittings
ASTM D 1746 : 2015 : REDLINE Standard Test Method for Transparency of Plastic Sheeting
ASTM D 1893 : 67(1985) TEST METHOD FOR BLOCKING OF PLASTIC FILM
ASTM D 1527 : 1999 : EDT 1 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80
ASTM D 2282 : 1999 : EDT 1 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)
ASTM F 735 : 2017 : REDLINE Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method
ASTM D 2740 : 1989 Specification for Polyvinyl Chloride (PVC) Plastic Tubing (Withdrawn 1989)
ASTM D 2293 : 1996 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ANSI INCITS 322 : 2015 INFORMATION TECHNOLOGY - CARD DURABILITY TEST METHODS
ASTM D 3122 : 2015 : REDLINE Standard Specification for Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings
ASTM F 878 : 1995 Specification for Polybutylene (PB) Thermoplastic Thin-Wall Drip Irrigation Tubing (Withdrawn 2000)
MIL-P-46122 Revision B:1975 PLASTIC MOLDING MATERIAL AND PLASTIC EXTRUSION MATERIAL, POLYVINYLIDENE FLUORIDE POLYMER AND COPOLYMER
ASTM D 2104 : 2003 Standard Specification for Polyethylene (PE) Plastic Pipe, Schedule 40 (Withdrawn 2010)
ASTM D 6835 : 2017 : REDLINE Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE)
ASTM D 5510 : 1994 : R2001 Standard Practice for Heat Aging of Oxidatively Degradable Plastics (Withdrawn 2010)
ASTM D 2924 : 2012 : R2017 Standard Test Method for External Pressure Resistance of “Fiberglass”<brk /> (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 2951 : 2000 Standard Test Method for Resistance of Types III and IV Polyethylene Plastics to Thermal Stress-Cracking (Withdrawn 2006)
MIL-C-44187 Revision C:1993 CLOTH, LAMINATED, WATERPROOF AND MOISTURE VAPOR PERMEABLE
ASTM D 5525 : 1994 : REV A Standard Practice for Exposing Plastics to a Simulated Active Landfill Environment (Withdrawn 2002)
ASTM D 3615 : 1987 Test Method for Chemical Resistance of Thermoset Molding Compouds Used in the Manufacture of Molded Fittings (Withdrawn 1993)
ASTM D 6338 : 2017 : REDLINE Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods
MIL-P-43043 Revision C:1978 PLASTIC MOLDING MATERIAL, PRE-MIX, POLYESTER, GLASS FIBER REINFORCED
CSA C22.2 No. 211.1 :2006 RIGID TYPES EB1 AND DB2/ES2 PVC CONDUIT
ASTM D 2992 : 2012 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM F 800 : 1989 Specification for Corrugated Poly(Vinyl Chloride) (PVC) Tubing and Compatible Fittings (Withdrawn 1992)
ASTM D 2750 : 1995 Specification for Acrylonitrile- Butadiene-Sytrene (ABS) Plastics Utilities Conduit and Fittings (Withdrawn 1997)
ASTM D 1201 : 2013 : REDLINE Standard Specification for Thermosetting Polyester Molding Compounds
ASTM D 2294 : 1996 : R2002 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 2318 : 1998 : R2008 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM F 392 : 1993 : R2004 Standard Test Method for Flex Durability of Flexible Barrier Materials
ASTM D 952 : 2015 : REDLINE Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials
ASTM D 2152 : 2017 : REDLINE Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion
ASTM D 6713 : 2014 : REDLINE Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF)
ASTM D 1547 : 1981 Specification for Extruded Acrylic Plastic Sheet (Withdrawn 1988)
ASTM D 1784 : 2011 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
MIL-P-997 Revision D:1966 PLASTIC MATERIAL, LAMINATED, THERMOSETTING, ELECTRIC INSULATION, SHEETS, GLASS CLOTH, SILICONE RESIN
MIL-P-46133 Revision A:1974 PLASTIC MOLDING AND EXTRUSION MATERIAL, POLY (ARYL SULFONE ETHER) RESIN, THERMOPLASTIC
MIL-P-46124 Revision B:1978 PLASTIC MOLDING AND EXTRUSION MATERIAL, IONOMER RESINS
ASTM D 2300 : 2008 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
ASTM D 7445 : 2018 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)
ASTM F 437 : 2015 : REDLINE Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
ASTM D 2464 : 2015 : REDLINE Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
ASTM D 4093 : 19951 Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials
ASTM D 4673 : 2016 : REDLINE Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials
AASHTO M 252 : 2009 SPECIFICATION FOR CORRUGATED POLYETHYLENE DRAINAGE PIPE
ASTM F 2600 : 2009 : R2013 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM E 765 : 1980 Practice for Evaluation of Cover Materials for Flat Plate Solar Collectors (Withdrawn 1991)
ASTM D 7293 : 2012 : REDLINE Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)
ASTM D 4335 : 1999 : R2010 Standard Test Method for Determination of Component Retention of a Mechanical Pump Dispenser
ASTM D 1779 : 1998 : R2017 Standard Specification for Adhesive for Acoustical Materials
ASTM D 3308 : 2012 : R2017 Standard Specification for PTFE Resin Skived Tape
ASTM D 5748 : 1995 : R2007 Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film
ASTM D 1931 : 1999 : R2004 Standard Specification for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical Insulation (Withdrawn 2013)
ASTM D 5169 : 1998 Standard Test Method for Shear Strength (Dynamic Method) of Hook and Loop Touch Fasteners
ASTM D 6005 : 2003 Standard Test Method for Determining Slump Resistance of Carpet Adhesives
ASTM F 2881 : 2011 Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
ASTM D 1527 : 1999 : R2005 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80 (Withdrawn 2014)
ASTM F 2390 : 2012 : R2017 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content
ASTM D 1248 : 2016 : REDLINE Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
ASTM D 1790 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 6777 : 2016 : REDLINE Standard Test Method for Relative Rigidity of Poly(Vinyl Chloride)(PVC) Siding
ASTM F 2818 : 2010 : R2014 : EDT 1 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM D 3034 : 2016 : REDLINE Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
ASTM D 6004 : 2004 : R2011 Standard Test Method for Determining Adhesive Shear Strength of Carpet Adhesives (Withdrawn 2020)
ASTM F 1974 : 2009 : R2015 Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
ASTM D 3914 : 2002 Standard Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod
ASTM D 2105 : 2001 Standard Test Method for Longitudinal Tensile Properties of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM G 137 : 1997 : R2003 Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
ASTM D 5946 : 2017 : REDLINE Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM F 2922 : 2013 : EDT 1 Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers
ASTM D 705 : 1999 : R2012 Standard Specification for Urea-Formaldehyde Molding Compounds
ASTM F 2881 : 2011 : R2015 Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
ASTM D 2952 : 1995 Specification for Ethylene Plastics (Withdrawn 1999)
ASTM F 545 : 1995 Specification for PVC and ABS Injected Solvent Cemented Plastic Pipe Joints (Withdrawn 2001)
ASTM F 409 : 2017 : REDLINE Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings
ASTM D 6005 : 2003 : R2017 Standard Test Method for Determining Slump Resistance of Carpet Adhesives (Withdrawn 2017)
ASTM D 907 : 2015 : REDLINE Standard Terminology of Adhesives
ASTM F 2806 : 2010 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR)
ASTM D 2103 : 2015 : REDLINE Standard Specification for Polyethylene Film and Sheeting
ASTM F 892 : 1995 Specification for Polyethylene (PE) Corrugated Pipe With a Smooth Interior and Fittings (Withdrawn 2001)
ASTM F 392 : 1993 : R1999 Standard Test Method for Flex Durability of Flexible Barrier Materials
ASTM D 1922 : 2015 : REDLINE Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 5748 : 1995 : R2001 Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film
ASTM D 5575 : 2007 Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
ASTM D 1238 : 2013 : REDLINE Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 3435 : 1980 Specification for Plastic Containers (Jerry Cans) for Petroleum Products (Withdrawn 1987)
ASTM F 2762 : 2011 : EDT 1 Standard Specification for 12 to 30 in. (300 to 750 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications (Withdrawn 2016)
ASTM D 3826 : 1998 Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
ASTM D 705 : 1999 : R2004 Standard Specification for Urea-Formaldehyde Molding Compounds
ASTM D 3368 : 2017 : REDLINE Standard Specification for FEP Sheet and Film
ASTM D 3308 : 2012 Standard Specification for PTFE Resin Skived Tape
ASTM G 21 : 2015 : REDLINE Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
ASTM D 5209 : 1992 Standard Test Method for Determining the Aerobic Biodegradation of Plastic Materials in the Presence of Municipal Sewage Sludge (Withdrawn 2004)
ASTM F 2947 : 2012 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM F 2763 : 2016 : REDLINE Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM D 5170 : 1998 : R2004 Standard Test Method for Peel Strength ("T" Method) of Hook and Loop Touch Fasteners
ASTM D 3916 : 2008 Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod
ASTM D 3214 : 1996 Standard Test Methods for Coating Powders and Their Coatings Used for Electrical Insulation (Withdrawn 2002)
ASTM D 2228 : 2004 : R2009 Standard Test Method for Rubber Property-Relative Abrasion Resistance by the Pico Abrader Method
ASTM F 2158 : 2008 Standard Specification for Residential Central-Vacuum Tube and Fittings
ASTM D 3028 : 1995 Standard Test Method for Kinetic Coefficient of Friction of Plastic Solids (Withdrawn 2000)
ASTM D 2680 : 2001 : R2014 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping
ASTM D 116 : 1986 : R2016 Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications
ASTM F 2969 : 2012 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) IPS Dimensioned Pressure Pipe
ASTM F 2468 : 2005 : R2011 Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications
ASTM F 794 : 2003 : R2014 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter
ASTM D 1931 : 1999 Standard Specification for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical Insulation
ASTM F 1306 : 2016 : REDLINE Standard Test Method for Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates
ASTM D 2732 : 2014 : REDLINE Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM E 906 : 2009 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method
ASTM D 6150 : 2016 : REDLINE Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility
ASTM D 1039 : 2016 : REDLINE Standard Test Methods for Glass-Bonded Mica Used as Electrical Insulation
ASTM F 736 : 2017 : REDLINE Standard Test Method for Impact Resistance of Monolithic Polycarbonate Sheet by Means of a Falling Weight
ASTM D 705 : 1999 Standard Specification for Urea-Formaldehyde Molding Compounds
ASTM F 791 : 1996 : R2013 Standard Test Method for Stress Crazing of Transparent Plastics
ASTM D 5171 : 2015 : REDLINE Standard Test Method for Impact Resistance of Plastic Sew-Through Buttons
ASTM D 5485 : 2016 : REDLINE Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter
ASTM F 2818 : 2010 : R2014 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM F 2686 : 2014 : REDLINE Standard Specification for Glass Fiber Reinforced Thermoplastic Pipe
ASTM F 2658 : 2007 : R2019 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings
ASTM D 5870 : 2016 : REDLINE Standard Practice for Calculating Property Retention Index of Plastics
ASTM F 2986 : 2012 Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications
ASTM D 4470 : 1997 : R2004 Standard Test Method for Static Electrification
ASTM F 1986 : 2001 : R2011 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems (Withdrawn 2020)
I.S. EN 14617-13:2013 AGGLOMERATED STONE - TEST METHODS - PART 13: DETERMINATION OF ELECTRICAL RESISTIVITY
MIL-P-46131 Revision B:1975 PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYPHENYLENE OXIDE, MODIFIED, GLASS FIBER REINFORCED
MIL-P-46129 Revision A:1975 PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYPHENYLENE OXIDE, MODIFIED
MIL-I-24683 Revision A:1990 INSULATION ELECTRICAL, HIGH TEMPERATURE INORGANIC PAPER
MIL-P-46144 Revision C:1986 PLASTIC SHEET, POLYCARBONATE
MIL P 46169 : A PLASTIC, SHEET MOLDING COMPOUND, POLYESTER, GLASS FIBER REINFORCED (FOR GENERAL PURPOSE APPLICATIONS)
MIL-P-46179 Revision A:1986 PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYAMIDE IMIDE
MIL-M-14 Revision H:1990 MOLDING COMPOUNDS, THERMOSETTING
MIL-P-46161 Revision A:1976 PLASTIC MOLDING MATERIAL, POLYTEREPHTHALATE THERMOPLASTIC, GLASS FIBER REINFORCED
MIL-P-46115 Revision B:1977 PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYPHENYLENE OXIDE
VDA 309 : 2016 EKB SPECIFICATIONS FOR DISC BRAKE PAD NOISE DAMPING SHIMS (INSULATORS)
ASTM D 1779 : 1998 Standard Specification for Adhesive for Acoustical Materials
ASTM D 4470 : 1997 : R2010 Standard Test Method for Static Electrification
ASTM D 5041 : 1998 Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Joints
DOD I 24683 : 1987 INSULATION ELECTRICAL, HIGH TEMPERATURE INORGANIC PAPER
ASTM G 74 : 2013 : REDLINE Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact
ASTM D 2684/D2684M : 2015 : REDLINE Standard Test Method for Permeability of Thermoplastic Containers to Packaged Reagents or Proprietary Products
ASTM D 2143 : 2015 : REDLINE Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
ASTM F 2922 : 2013 Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers
WW-L-2887 Base Document:1998 TUBE, PHENOLIC, POROUS RETAINER FOR USE IN INSTRUMENT BEARINGS
SAE AMS 3733 : 2015 POTTING COMPOUND, EPOXY, TWO PART, HIGHLY FILLED, HEAT CURE, HIGH COMPRESSIVE STRENGTH
SAE J 2253 : 2017 TEST PROCEDURES FOR AUTOMOTIVE STRUCTURAL COMPOSITE MATERIALS
ASTM D 3089 : 1997 : R2003 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 5934 : 2002 Standard Test Method for Determination of Modulus of Elasticity for Rigid and Semi-Rigid Plastic Specimens by Controlled Rate of Loading Using Three-Point Bending (Withdrawn 2009)
ASTM D 4272/D4272M : 2015 : REDLINE Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
ASTM D 4617 : 2003 Standard Classification System for Phenolic Compounds (PF) (Withdrawn 2012)
CSA S807 : 2010 SPECIFICATION FOR FIBRE-REINFORCED POLYMERS
ASTM D 2442 : 1975 : R1996 Standard Specification for Alumina Ceramics for Electrical and Electronic Applications
ASTM D 116 : 1986 : R1999 Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications
CSA C22.2 No. 211.1 : 2006 : INC : UPD 1 : 2012 : R201100 RIGID TYPES EB1 AND DB2/ES2 PVC CONDUIT
MIL-P-43038 Revision B:1973 PLASTIC MOLDING MATERIAL, POLYESTER, LOW PRESSURE LAMINATING, HIGH TEMPERATURE RESISTANT
ISO 15840:2004 Ships and marine technology Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications
ASTM F 2658 : 2007 : R2013 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings
ASTM D 4703 : 2016 : REDLINE Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
MIL-I-24718 Base Document:1990 INSULATING RESINS, SOLVENTLESS, VACUUM-PRESSURE-IMPREGNATING - GENERAL SPECIFICATION FOR
ASTM D 1998 : 2015 : REDLINE Standard Specification for Polyethylene Upright Storage Tanks
ASTM F 2987 : 2012 Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications
ASTM F 1380 : 1995 : REV A : R2002 Standard Specification for Metal Insert Fittings for Polybutylene (PB) Tubing
ASTM D 7472 : 2009 : R2014 Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials
ASTM D 3295 : 2015 : REDLINE Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing
ASTM D 4357 : 1996 Standard Specification for Plastic Laminates Made from Woven-Roving and Woven-Yarn Glass Fabrics (Withdrawn 2004)
ASTM D 2741 : 1995 : R2001 Standard Test Method for Susceptibility of Polyethylene Bottles to Soot Accumulation
ASTM D 3528 : 1996 Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
MIL C 43473 : F CLOTH, COATED, NYLON, POLYURETHANE COATED
ASTM D 6867 : 2003 Standard Specification for Perfluoroalkoxy (PFA)-Fluoropolymer Tubing
ASTM D 2468 : 1996 : REV A Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40 (Withdrawn 2003)
AASHTO M 330 : 2013 SPECIFICATION FOR POLYPROPYLENE PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER
ASTM E 906/E906M : 2017 : REDLINE Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method
ASTM D 2291/D2291M : 2016 : REDLINE Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites
ASTM D 7567 : 2009 Standard Test Method for Determining Gel Content in Crosslinked Ethylene Plastics Using Pressurized Liquid Extraction (Withdrawn 2015)
L-P-398 Revision B:1973 PLASTIC MOLDING MATERIAL STYRENE-BUTADIENE
MIL-P-22241 Revision B:1973 PLASTIC SHEET (AND FILM) POLYTETRAFLUOROETHYLENE (TFE-FLUOROCARBON RESIN)
ASTM D 3826 : 1998 : R2013 Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
MIL-L-24518 Base Document:1975 LAMINATE, VINYL FILM ALUMINUM, DECORATIVE
ASTM G 176 : 2003 : R2009 Standard Test Method for Ranking Resistance of Plastics to Sliding Wear using Block-on-Ring Wear Test—Cumulative Wear Method
ASTM F 679 : 2016 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings
MIL-P-46067 Revision B:1977 PLASTIC EMBEDDING COMPOUND, EPOXY RESIN SYSTEM
MIL-P-14591 Revision D:1976 PLASTIC FILM, NONRIGID, TRANSPARENT
ASTM D 1202 : 1984 Specification for Plasticized Cellulose Acetate Sheet and Film for Primary Insulation (Withdrawn 1990)
ASTM D 2293 : 1996 : R2002 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
FM 1614 : 2017 FIBER REINFORCED COMPOSITE (FRC) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE
ASTM D 3222 : 2005 : R2015 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
MIL-P-46036 Revision B:1973 PLASTIC SHEET, RODS, TUBES AND DISCS, POLYCHLOROTRIFLUOROETHYLENE
ASTM F 1380 : 1995 : REV A : R2002 : EDT 1 Standard Specification for Metal Insert Fittings for Polybutylene (PB) Tubing (Withdrawn 2008)
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 5575 : 2007 : R2013 Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
ASTM D 2238 : 1992 : R2004 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm
ASTM D 2318 : 1998 : R2003 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 1430 : 2017 : REDLINE Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
ASTM D 5083 : 2017 : REDLINE Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
SAE AMS 3613 : 2016 FILM, COPPER CLAD POLYESTER
TAPPI T 565 : 0 CONTACT ANGLE OF WATER DROPLETS ON CORONA-TREATED POLYMER FILM SURFACES
AASHTO M 304 : 2011 : R2015 SPECIFICATION FOR POLY(VINYL CHLORIDE) (PVC) PROFILE WALL DRAIN PIPE AND FITTINGS BASED ON CONTROLLED INSIDE DIAMETER
ASTM F 635 : 1985 : R1991 Guide for Selection of Tests for Material Properties of Liquid Thermoset Encapsulating Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996)
ASTM D 5948 : 2005 Standard Specification for Molding Compounds, Thermosetting
ASTM D 2295 : 1996 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 704 : 1999 Standard Specification for Melamine-Formaldehyde Molding Compounds
ASTM D 7793 : 2017 : REDLINE Standard Specification for Insulated Vinyl Siding
ASTM D 2293 : 1996 : R2016 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
L-P-399 Revision B:1970 PLASTIC MOLDING MATERIAL, ION MATERIAL, STYRENE ACRYLONITRILE COPOLYMERS
ASTM D 2303 : 1997 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 2442 : 1975 : R2012 Standard Specification for Alumina Ceramics for Electrical and Electronic Applications
ASTM D 7474 : 2017 : REDLINE Standard Practice for Determining Residual Stresses in Extruded or Molded Sulfone Plastic (SP) Parts by Immersion in Various Chemical Reagents
ASTM D 6325 : 1998 Test Method for Determining Open Assembly Time of Carpet Mastic Adhesives
MIL-A-2334 Revision J:1991 APRON, TOXICOLOGICAL AGENTS PROTECTIVE, M-2
MIL-DTL-64154 Revision B:2008 LAMINATE: FIBERGLASS-FABRIC-REINFORCED, PHENOLIC
ASTM D 788 : 2016 : REDLINE Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds
ASTM D 794 : 1993 Practice for Determining Permanent Effect of Heat on Plastics (Withdrawn 1998)
ASTM D 2288 : 1997 : R2001 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
L-P-527 Revision B:1973 PLASTIC SHEET, STYRENE-BUTADIENE
MIL-A-50424 Base Document:1969 ACETAL, SHEETING (FOR USE WITH AMMUNITION)
ASTM F 512 : 2012 Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation
ASTM D 3045 : 1992 : R2010 Standard Practice for Heat Aging of Plastics Without Load
ASTM D 5509 : 1996 Standard Practice for Exposing Plastics to a Simulated Compost Environment (Withdrawn 2002)
ASTM D 1434 : 1982 : R1998 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 3045 : 1992 PRACTICE FOR HEAT AGING OF PLASTICS WITHOUT LOAD
ASTM D 6324 : 2011 Standard Test Methods for Male Condoms Made from Polyurethane
ASTM D 2296 : 2001 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
CSA Z218.1 : 0 STANDARD PRACTICE FOR EXPOSING PLASTICS TO A SIMULATED SOIL ENVIRONMENT
ASTM D 2295 : 1996 : R2016 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
SAE AMS P 21922 : 2016 PLASTIC RODS AND TUBES, POLYETHYLENE
ASTM D 2343 : 2017 : REDLINE Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics
ASTM D 2288 : 1997 Standard Test Method for Weight Loss of Plasticizers on Heating
ASTM D 955 : 2008 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
SAE J 1390 : 2017 ENGINE COOLING FAN STRUCTURAL ANALYSIS
ASTM F 480 : 2014 : REDLINE Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
ASTM D 1822 : 2013 : REDLINE Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ASTM D 4097 : 2001 Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
SAE J 3042 : 2015 MEASURING PROPERTIES OF LI-BATTERY ELECTROLYTE
ASTM F 1533 : 2001 Standard Specification for Deformed Polyethylene (PE) Liner
ASTM D 4396 : 2015 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications
ASTM D 696 : 2016 : REDLINE Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
ASTM D 3914 : 2002 : R2008 Standard Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod
AASHTO MP 35 : 2018 SPECIFICATION FOR THIN OVERLAY TREATMENTS USING A BINDER RESIN SYSTEM AND AGGREGATE FOR CONCRETE SURFACES
ASTM D 6098 : 2016 : REDLINE Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC)
ASTM F 1380 : 1995 : REV A Standard Specification for Metal Insert Fittings for Polybutylene (PB) Tubing
ASTM D 704 : 1999 : R2012 Standard Specification for Melamine-Formaldehyde Molding Compounds
ASTM D 6054 : 1997 Standard Practice for Conditioning Electrical Insulating Materials for Testing
ASTM D 4021 : 1992 Standard Specification for Glass-Fiber-Reinforced Polyester Underground Petroleum Storage Tanks (Withdrawn 1999)
ASTM D 568 : 1977 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Flexible Plastics in a Vertical Position
ASTM G 176 : 2003 : R2017 Standard Test Method for Ranking Resistance of Plastics to Sliding Wear Using Block-on-Ring Wear Test—Cumulative Wear Method
ASTM D 651 : 1984 Method of Test for Tensile Strength of Molded Electrical Insulating Materials (Withdrawn 1989)
ASTM F 1335 : 2004 Standard Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service (Withdrawn 2011)
(INACTIVE RECORD)ASTM D 5336 : 2015-04 CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPHTHALAMIDE (PPA) INJECTION MOLDING MATERIALS
ASTM D 5169 : 1998 : R2010 Standard Test Method for Shear Strength (Dynamic Method) of Hook and Loop Touch Fasteners
ASTM D 5319 : 2017 : REDLINE Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels
ASTM F 1957 : 1999 : R2017 Standard Test Method for Composite Foam Hardness-Durometer Hardness
CSA C22.2 No. 62 : 1993 : R2008 SURFACE RACEWAY SYSTEMS
ASTM D 4067 : 2016 : REDLINE Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
ASTM D 5422 : 2017 : REDLINE Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer
ASTM D 4476/D4476M : 2014 : REDLINE Standard Test Method for Flexural Properties of Fiber Reinforced Pultruded Plastic Rods
ASTM D 2288 : 1997 : R2001 Standard Test Method for Weight Loss of Plasticizers on Heating (Withdrawn 2010)
ASTM D 1434 : 1982 : R2015 : EDT 1 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM F 1974:2009 Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
ASTM F 1336 : 2015 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings
ASTM D 4801 : 2008 Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm [0.010 in.] and Greater
ASTM F 1735:2009 Standard Specification for Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits
ASTM F 1281 : 2017 : REDLINE Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe
ASTM F 2658 : 2007 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings
ASTM F 1499 : 2017 : REDLINE Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 1822M : 1993 Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials (Withdrawn 1996)
ASTM D 5418 : 2015 : REDLINE Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Dual Cantilever Beam)
ASTM D 1203 : 2016 : REDLINE Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods
ASTM F 2433 : 2005 : R2009 Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
CSA C22.2 No. 207 : 2015 PORTABLE AND STATIONARY ELECTRIC SIGNS AND DISPLAYS
ASTM F 845 : 1996 Standard Specification for Plastic Insert Fittings for Polybutylene (PB) Tubing (Withdrawn 2003)
CSA C22.2 No. 0.17 : 2000 EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS
ASTM D 5170 : 1998 Standard Test Method for Peel Strength ("T" Method) of Hook and Loop Touch Fasteners
ASTM D 1712 : 2009 Standard Practice for Resistance of Plastics to Sulfide Staining
ASTM D 5511 : 2018 : REDLINE Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions
ASTM D 3275 : 2008 : R2013 Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials
ASTM F 1634 : 1995 : R2008 Standard Practice for <span class="bdit">In-Vitro</span> Environmental Conditioning of Polymer Matrix Composite Materials and Implant Devices
ASTM D 2442 : 1975 : R2001 Standard Specification for Alumina Ceramics for Electrical and Electronic Applications
ASTM D 6867 : 2003 : R2014 Standard Specification for Perfluoroalkoxy (PFA)-Fluoropolymer Tubing
ASTM D 5279 : 2013 : REDLINE Standard Test Method for Plastics: Dynamic Mechanical Properties: In Torsion
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials
ASTM D 6262 : 2017 : REDLINE Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 1634 : 1995 : R2016 Standard Practice for <emph type="bdit">In-Vitro</emph> Environmental Conditioning of Polymer Matrix Composite Materials and Implant Devices (Withdrawn 2017)
ASTM D 4350 : 2016 : REDLINE Standard Test Method for Corrosivity Index of Plastics and Fillers
ASTM D 3275 : 2008 Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials
ASTM D 2467 : 2015 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
ASTM D 3013 : 2013 : REDLINE Standard Specification for Epoxy Molding Compounds
ASTM F 3219 : 2017 Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
ASTM D 4335 : 1999 Standard Test Method for the Determination of the Component Retention of a Mechanical Pump Dispenser
ASTM D 5676 : 1999 Standard Specification for Recycled Polystyrene Molding and Extrusion Materials (Withdrawn 2004)
ASTM D 8136 : 2017 Standard Test Method for Determining Plastic Film Thickness and Thickness Variability Using a Non-Contact Capacitance Thickness Gauge
ASTM D 2680 : 2001 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping
ASTM F 3253 : 2017 Standard Specification for Crosslinked Polyethylene (PEX) Tubing with Oxygen Barrier for Hot- and Cold-Water Hydronic Distribution Systems
ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
ASTM F 791 : 1996 : R2002 Standard Test Method for Stress Crazing of Transparent Plastics
ASTM D 2997 : 2015 : REDLINE Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 5721 : 2008 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM F 2928 : 2013 Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods
ASTM D 1779 : 1998 : R2004 Standard Specification for Adhesive for Acoustical Materials
ASTM D 2843 : 2016 : REDLINE Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics
ASTM D 1622/D1622M : 2014 : REDLINE Standard Test Method for Apparent Density of Rigid Cellular Plastics
ASTM D 2517 : 2018 : REDLINE Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings
ASTM D 3159 : 2015 : REDLINE Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials
ASTM F 2433 : 2005 : R2013 Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
ASTM D 704 : 1999 : R2004 Standard Specification for Melamine-Formaldehyde Molding Compounds
ASTM F 512 : 2012 : R2017 Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation
ASTM F 2854 : 2010 Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing
ASTM F 3036 : 2013 Standard Guide for Testing Absorbable Stents
ASTM D 345 : 2002 Side bearings of the freight wagon bogies. General specifications
ASTM D 2411 : 1989 SPECIFICATION FOR CELLULOSE ACETATE BUTYRATE FILM AND SHEETING FOR FABRICATING AND FORMING
NEMA TC 6&8 : 2013 POLYVINYL CHLORIDE (PVC) PLASTIC UTILITIES DUCT FOR UNDERGROUND INSTALLATIONS
NEMA TC 12 : 1991 CORRUGATED POLYVINYL CHLORIDE (PVC) COILABLE PLASTIC UTILITIES DUCT
NEMA TC 10 : 1993 PVC PLASTIC COMMUNICATIONS DUCT AND FITTINGS FOR UNDERGROUND INSTALLATION
AASHTO R 63 : 2013 PRACTICE FOR SOLID WALL HIGH-DENSITY POLYETHYLENE (HDPE) CONDUIT FOR NON-PRESSURE APPLICATIONS USED FOR THE PROTECTION OF POWER AND TELECOMMUNICATIONS CABLES
NEMA TC 13:2014(R2019) Electrical Nonmetallic Tubing (ENT)
NEMA TC 8 : 1999 PVC PLASTIC UTILITIES DUCT FOR UNDERGROUND INSTALLATIONS
NEMA TC 5 : 1990 CORRUGATED POLYOLEFIN COILABLE PLASTIC UTILITIES DUCT
NEMA TC 15 : 1993 CORRUGATED POLYVINYL CHLORIDE (PVC) FIBER OPTIC INNERDUCT
NEMA TC 2 : 2013 ELECTRICAL POLYVINYL CHLORIDE (PVC) TUBING AND CONDUIT
ASTM F 2762 : 2011 Standard Specification for 12 to 30 in. [300 to 750 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM F 949 : 2015 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings
ASTM D 3287 : 1989 Specification for Biaxially Oriented Polyethylene (PEO) Plastic Pipe (SDR-PR) Based on Controlled Outside Diameter (Withdrawn 1989)
ASTM G 175 : 2013 : REDLINE Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications
ASTM D 2561 : 2017 : REDLINE Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers
ASTM D 2734 : 2016 : REDLINE Standard Test Methods for Void Content of Reinforced Plastics
ASTM D 4226 : 2016 : REDLINE Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products
L-C-530 Revision C:1987 COATING, PIPE, THERMOPLASTIC RESIN
MIL-PRF-21922 Revision C:2015 PLASTIC RODS AND TUBES, POLYETHYLENE
ASTM D 2834 : 1995 : R2008 Standard Test Method for Nonvolatile Matter (Total Solids) in Water-Emulsion Floor Polishes, Solvent-Based Floor Polishes, and Polymer-Emulsion Floor Polishes
ASTM F 2562/F2562M : 2015 : REDLINE Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage
ASTM D 2228 : 2004 : EDT 1 Standard Test Method for Rubber Property-Relative Abrasion Resistance by the Pico Abrader Method
ASTM D 6394 : 2014 : REDLINE Standard Specification for Sulfone Plastics (SP)
AASHTO M 326 : 2008 SPECIFICATION FOR POLYETHYLENE (PE) LINER PIPE, 300- TO 1600-MM DIAMETER, BASED ON CONTROLLED OUTSIDE DIAMETER
ASTM D 2228 : 2004 : R2015 Standard Test Method for Rubber Property—Relative Abrasion Resistance by Pico Abrader Method
ASTM D 4068 : 2017 : REDLINE Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane
SAE AMS 3686 : 2014 ADHESIVE, POLYIMIDE RESIN, FILM AND PASTE HIGH TEMPERATURE RESISTANT, 315 DEGREES C (599 DEGREES F)
ASTM D 787 : 2012-08 SPECIFICATION FOR ETHYL CELLULOSE MOLDING AND EXTRUSION COMPOUNDS
AASHTO M 278 : 2015 SPECIFICATION FOR CLASS PS46 POLY(VINYL CHLORIDE) (PVC) PIPE
ASTM D 2751 : 2005 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014)
ASTM D 2288 : 1997 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM G 176 : 2003 Standard Test Method for Ranking Resistance of Plastics to Sliding Wear using Block-on-Ring Wear Test—Cumulative Wear Method
ASTM D 1636 : 2013 : REDLINE Standard Specification for Allyl Molding Compounds
ASTM D 5926 : 2015 : REDLINE Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems
A-A-59403 Revision A:2008
ASTM D 2287 : 2012 : REDLINE Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds
ASTM D 671 : 1993 Standard Test Method for Flexural Fatigue of Plastics by Constant-Amplitude-of-Force (Withdrawn 2002)
ASTM D 4495 : 2016 : REDLINE Standard Test Method for Impact Resistance of Poly(Vinyl Chloride) (PVC) Rigid Profiles by Means of a Falling Weight
ASTM D 2105 : 2001 : R2007 : EDT 1 Standard Test Method for Longitudinal Tensile Properties of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM D 2587 : 1968 : R1985 Method of Test for Acetone Extraction and Ignition of Strands, Yarns, and Roving for Reinforced Plastics (Withdrawn 1988)
ASTM D 4634 : 2016 : REDLINE Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)
ASTM D 4093 : 1995 : R2001 : EDT 1 Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials
ASTM D 2300 : 2008 : R2017 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 7992/D7992M : 2015 Standard Practice for Elevated Temperature and Moisture Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs
ASTM F 1673 : 2010 Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems
ASTM D 2319/D2319M : 1998 : R2013 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
CSA C22.2 No. 0.17 : 2000 : R2004 EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS
ASTM D 5109 : 2012 : REDLINE Standard Test Methods for Copper-Clad Thermosetting Laminates for Printed Wiring Boards
ASTM F 1634 : 1995 : R2000 Standard Practice for In-Vitro Environmental Conditioning of Polymer Matrix Composite Materials and Implant Devices
ASTM D 4093 : 1995 : R2005 : EDT 1 Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials
ASTM F 1957 : 1999 : R2004 Standard Test Method for Composite Foam Hardness-Durometer Hardness
ASTM D 3307 : 2016 : REDLINE Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
SAE AMS P 46144 : 2015 PLASTIC SHEET, POLYCARBONATE
ASTM D 2303 : 1997 : R2004 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
MIL-P-20689 Revision D:1988 PLASTIC PLASTISOL (FOR COATING METALLIC OBJECTS)
ASTM F 441/F441M : 2015 : REDLINE Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
MIL-P-24364 Base Document:1969 PLASTIC SHEET, LAMINATED, THERMOSETTING, ELECTRICAL INSULATING SHEET, GLASS MAT
ASTM D 4611 : 2016 : REDLINE Standard Test Method for Specific Heat of Rock and Soil
AASHTO MP 20 : 2013 SPECIFICATION FOR STEEL-REINFORCED POLYETHYLENE (PE) RIBBED PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER
L-P-391 Revision D:1975 PLASTIC SHEETS, RODS AND TUBING, RIGID CAST, METHACRYLATE (MULTIAPPLICATIONS)
L-P-1183 Revision B:1977 PLASTIC MOLDING MATERIAL, ACRYLONITRILE-BUTADIENE-STYRENE (ABS), RIGID
ASTM D 2672 : 2014 : REDLINE Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement
ASTM D 4475 : 2002 : R2008 Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method
ASTM D 1337 : 2010 : R2016 Standard Practice for Storage Life of Adhesives by Viscosity and Bond Strength
ASTM D 7853 : 2013 Standard Test Method for Hydraulic Pullout Resistance of a Geomembrane with Locking Extensions Embedded in Concrete
ASTM F 1614 : 1999 : R2006 Standard Test Method for Shock Attenuating Properties of Materials Systems for Athletic Footwear
MIL P 21922 : B PLASTIC RODS AND TUBES, POLYETHYLENE
SAE AMS 3847 : 1994(S2016) CLOTH, QUARTZ, 'B' STAGE POLYIMIDE RESIN IMPREGNATED, STYLE 581 FABRIC, 315 DEGREES C (599 DEGREES F)
MIL C 20696 : E CLOTH, COATED, POLYESTER OR NYLON, WATERPROOF
ASTM D 7106/D7106M : 2005 : R2015 : EDT 1 Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes
ASTM F 1533 : 2001 : R2009 Standard Specification for Deformed Polyethylene (PE) Liner (Withdrawn 2018)
ASTM D 6100 : 2017 : REDLINE Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)
ASTM F 2929 : 2017 : REDLINE Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig
ASTM D 6988 : 2013 : REDLINE Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM F 3128 : 2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core
MIL-PRF-24172 Revision B:2004 INSULATION, PLASTIC, CELLULAR FOAM, RIGID, PREFORMED AND FOAM-IN-PLACE
ASTM D 4551 : 2017 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane
ASTM D 2671 : 2013 Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use
ASTM D 542 : 2014 : REDLINE Standard Test Method for Index of Refraction of Transparent Organic Plastics
ASTM D 3000 : 1995 : REV A : EDT 1 Standard Specification for Polybutylene (PB) Plastic Pipe (SDR-PR) Based on Outside Diameter (Withdrawn 2003)
ASTM F 2947 : 2012 : EDT 1 Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM F 1483 : 2017 : REDLINE Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe
ASTM D 5930 : 2017 : REDLINE Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique
ASTM F 2600 : 2009 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
CSA B137 COMPENDIUM : 2017 THERMOPLASTIC PRESSURE PIPING COMPENDIUM
ASTM D 6395 : 2011 : REDLINE Standard Test Method for Flatwise Flexural Impact Resistance of Rigid Plastics
ASTM D 1894 : 2014 : REDLINE Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM F 2984 : 2013 Standard Specification for Segmental Panel System for the Grout-in-Place-Liner (GIPL) Rehabilitation Method of Existing Man-Entry Size Sewers, Culverts, and Conduits
ASTM F 439 : 2013 : REDLINE Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
ASTM D 3045 : 1992 : R1997 Standard Practice for Heat Aging of Plastics Without Load
ASTM D 2318 : 1998 : R2013 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 7106 : 2005 Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes
ASTM D 7475 : 2011 Standard Test Method for Determining the Aerobic Degradation and Anaerobic Biodegradation of Plastic Materials under Accelerated Bioreactor Landfill Conditions
ASTM D 2238 : 1992 : R2012 : EDT 1 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm<sup>−1</sup> (Withdrawn 2021)
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
CSA C22.2 No. 0.17 : 2000 : R2013 EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS
ASTM G 147 : 2017 : REDLINE Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
ASTM D 2282 : 1999 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)
ASTM D 7471 : 2009 Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials
ASTM G 125 : 2000 : R2008 Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants
ASTM F 2863 : 2011 : R2016 Standard Specification for Central Vacuum Hose Inlet Valve Socket Dimensions
ASTM F 510 : 1993 : R2008 Standard Test Method for Resistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method
ASTM D 7792/D7792M : 2015 Standard Practice for Freeze/Thaw Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs
ASTM F 2968/F2968M : 2014 Standard Specification for Black Crosslinked Polyethylene (PEX) Pipe, Fittings and Joints For Gas Distribution Applications
ASTM D 5023 : 2015 : REDLINE Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending)
ASTM D 4100 : 1982 : R1989 : EDT 1 Test Method for Gravimetric Determination of Smoke Particulates from Combustion of Plastic Materials (Withdrawn 1997)
ASTM D 1638 : 1974 METHODS OF TESTING URETHANE FOAM ISOCYANATE RAW MATERIALS
ASTM D 1638 : 1974 : EDT 1 Methods of Testing Urethane Foam Isocyanate Raw Materials
ASTM D 1337:2010 Standard Practice for Storage Life of Adhesives by Viscosity and Bond Strength
ASTM D 6004 : 2004 Standard Test Method for Determining Adhesive Shear Strength of Carpet Adhesives
CSA C22.2 No. 327 : 2016 HDPE CONDUIT, CONDUCTORS-IN-CONDUIT, AND FITTINGS
ASTM D 5204 : 2017 : REDLINE CLASSIFICATION SYSTEM FOR POLYAMIDE-IMIDE (PAI) MOLDING AND EXTRUSION MATERIALS
ASTM D 1897 : 1988 Recommended Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials (Withdrawn 1992)
ASTM D 785 : 2008 : R2015 Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
ASTM D 5169 : 1998 : R2015 Standard Test Method for Shear Strength (Dynamic Method) of Hook and Loop Touch Fasteners
ASTM D 4203 : 2017 : REDLINE Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials
ASTM D 695 : 2015 : REDLINE Standard Test Method for Compressive Properties of Rigid Plastics
ASTM F 791 : 1996 : R2008 Standard Test Method for Stress Crazing of Transparent Plastics
ASTM D 7193 : 2017 : REDLINE Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape
SAE AMS 3666 : 2012 POLYTETRAFLUOROETHYLENE (PTFE) SHEET, GLASS CLOTH REINFORCED
ASTM D 149 : 2009 : R2013 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
ASTM F 1128 : 1988 Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using Salt Impingement Method (Withdrawn 1996)
ASTM D 5857 : 2017 : REDLINE Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology
ASTM PS 106 : 2001 Provisional Standard Specification for Rods and Tubes of Polyethylene (PE)
ASTM D 6339 : 2011 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)
CSA B1800 SERIES : 2015 THERMOPLASTIC NON-PRESSURE PIPING COMPENDIUM
CSA C22.2 No. 211.2 : 2006 RIGID PVC (UNPLASTICIZED) CONDUIT
ASTM F 1735 : 2009 : R2015 Standard Specification for Poly (Vinyl Chloride) (PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits
ASTM D 5229/D5229M : 2014-06 TEST METHOD FOR MOISTURE ABSORPTION PROPERTIES AND EQUILIBRIUM CONDITIONING OF POLYMER MATRIX COMPOSITE MATERIALS
ASTM D 5748 : 1995 : R2012 Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film
ASTM D 2659 : 2016 : REDLINE Standard Test Method for Column Crush Properties of Blown Thermoplastic Containers
ASTM D 4335 : 1999 : R2006 Standard Test Method for Determination of Component Retention of a Mechanical Pump Dispenser
ASTM D 732 : 2017 : REDLINE Standard Test Method for Shear Strength of Plastics by Punch Tool
ASTM D 5748 : 1995 Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film
ASTM D 5026 : 2015 : REDLINE Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension
ASTM D 1204 : 2014 : REDLINE Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 4349 : 2016 : REDLINE Classification System and Basis for Specification for Polyphenylene Ether (PPE) Materials
ASTM E 2945 : 2014 Standard Test Method for Film Permeability Determination Using Static Permeability Cells
ASTM D 5338 : 2015 : REDLINE Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials Under Controlled Composting Conditions, Incorporating Thermophilic Temperatures
ASTM D 3528 : 1996 : R2016 Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
ASTM D 2235 : 2004 : R2016 Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
ASTM D 7027 : 2013 : REDLINE Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine
ASTM F 793/F793M : 2015 : REDLINE Standard Classification of Wall Coverings by Use Characteristics
ASTM F 1365 : 1991 : R2013 Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
ASTM F 1365 : 1991 : R2018 Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
ASTM D 3485 : 2015 Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC)
ASTM D 6113 : 2016 : REDLINE Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM F 1365 : 1991 : R2009 Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
ASTM F 1365 : 1991 : R1999 : EDT 1 Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
ASTM F 1365 : 1991 : R2005 Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
UNI EN 14617-13 : 2013 AGGLOMERATED STONE - TEST METHODS - PART 13: DETERMINATION OF ELECTRICAL RESISTIVITY
CSA B182.7 : 2006 PSM TYPE MULTILAYER POLYVINYLCHLORIDE (PVC) SEWER PIPE HAVING REPROCESSED-RECYCLED CONTENT
ASTM F 510 : 1993 : R2004 Standard Test Method for Resistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method
ASTM D 5041 : 1998 : R2012 Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Joints
ASTM D 2296 : 2001 : R2006 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
SAE AMS 3612 : 2016 POLYESTER FILM, ELECTRICAL GRADE, GENERAL PURPOSE
SAE J 1474 : 2009 HEAVY-DUTY NONMETALLIC ENGINE COOLING FANS - MATERIAL, MANUFACTURING, AND TEST CONSIDERATIONS
ASTM D 2680 : 2001 : R2009 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping
ASTM D 6712 : 2017 : REDLINE Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes
ASTM D 2310 : 2006 : R2012 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 2116 : 2016 : REDLINE Standard Specification for FEP Resin Molding and Extrusion Materials
SAE AMS 3650 : 2012 RODS, SHEETS, AND MOLDED SHAPES, POLYCHLOROTRIFLURORETHYNEN (PCTFE) UNPLASTICIZED
ASTM F 876 : 2017 : REDLINE SPECIFICATION FOR CROSSLINKED POLYETHYLENE (PEX) TUBING
ASTM D 2310 : 2006 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM F 2561 : 2017 : REDLINE Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner
L-P-512 Revision C:1977 PLASTIC SHEET (SHEETING); POLYETHYLENE
ASTM F 810 : 2012 Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields
ASTM D 3846 : 2008 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics
L-P-1036 Revision A:1974 PLASTIC ROD, SOLID: PLASTIC TUBES AND TUBING, HEAVY WALLED: POLYVINYL CHLORIDE, RIGID
MIL-P-46112 Revision B:1977 PLASTIC SHEET & STRIP, POLYMIDE
DWA-M 143-20:2018 TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS
MIL-P-46121 Revision B:1977 ELASTIC SHEET AND COATING MATERIAL, PARA-XYLYLENE POLYMERS
ASTM D 638M : 1996 Standard Test Method for Tensile Properties of Plastics (Metric) (Withdrawn 1998)
ASTM D 3354 : 2015 : REDLINE Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM F 2158 : 2008 : R2013 Standard Specification for Residential Central-Vacuum Tube and Fittings
ASTM D 2924 : 2012 Standard Test Method for External Pressure Resistance of “Fiberglass”<brk /> (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 3089 : 1997 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
MIL-C-46866 Base Document:1973 COMPOUND, EPOXY MOLDING AND APPLICATION OF
ASTM D 1929 : 2016 : REDLINE Standard Test Method for Determining Ignition Temperature of Plastics
ASTM D 6263 : 2015 : REDLINE Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC)
ASTM D 5170 : 1998 : R2015 Standard Test Method for Peel Strength (“T” Method) of Hook and Loop Touch Fasteners
ASTM D 4098 : 1982 : R1987 : EDT 1 Practice for Evaluating High-Density Rigid Cellular Thermosets (Withdrawn 1994)
ASTM G 125 : 2000 : R2015 Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants
ASTM F 2829 : 2010 Standard Specification for Metric-Sized Crosslinked Polyethylene (PEX) Pipe Systems
ASTM D 2238 : 1992 : R1999 Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm
ASTM F 734 : 2017 : REDLINE Standard Test Method for Shear Strength of Fusion Bonded Polycarbonate Aerospace Glazing Material
ASTM D 6325 : 1998 : R2004 Test Method for Determining Open Assembly Time of Carpet Mastic Adhesives
MIL-I-24768 Base Document:1992 INSULATION, PLASTICS, LAMINATED, THERMOSETTING, GENERAL SPECIFICATION FOR
ASTM D 746 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
ASTM F 794:2003 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter
02/713763 DC : DRAFT DEC 2002 ISO 15840 - SHIPS AND MARINE TECHNOLOGY - STANDARD SPECIFICATION FOR THERMOSETTING RESIN FIBREGLASS PIPE AND FITTINGS TO BE USED FOR MARINE APPLICATIONS
ASTM D 3835 : 2016 : REDLINE Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
ASTM F 1957 : 1999 Standard Test Method for Composite Foam Hardness-Durometer Hardness
MIL-M-87176 Base Document:1982 MOLDING MATERIAL, POLYPROPYLENE, MODIFIED MECHANICAL USE ONLY
ASTM D 3528 : 1996 : R2002 Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
ASTM D 3528 : 1996 : R2008 Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
ASTM D 1710 : 2015 : REDLINE Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes
MIL-I-3190 Revision F:1991 INSULATION SLEEVING, ELECTRICAL, FLEXIBLE, COATED, GENERAL SPECIFICATION FOR
ADS-13F-HDBK : 1997 AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES
ASTM D 2852 : 2016 : REDLINE Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings
ASTM D 3222 : 2005 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 2632 : 2015 : REDLINE Standard Test Method for Rubber Property—Resilience by Vertical Rebound
ASTM D 3420 : 2014 : REDLINE Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 1868 : 2013 : REDLINE Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems
ASTM D 5117 : 2017 : REDLINE Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock
ASTM D 4397 : 2016 : REDLINE Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications
ASTM D 2294 : 1996 : R2008 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM F 438 : 2017 : REDLINE Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40
ASTM D 7192 : 2010 Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 1494 : 2017 : REDLINE Standard Test Method for Diffuse Light Transmission Factor of Reinforced Plastics Panels
ASTM F 1957 : 1999 : R2011 Standard Test Method for Composite Foam Hardness-Durometer Hardness
ASTM D 5205 : 2016 : REDLINE Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
ASTM D 2307 : 2007 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 695M : 1991 Test Method for Compressive Properties of Rigid Plastics (Metric) (Withdrawn 1996)
ASTM D 2665 : 2014 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM D 3965 : 2016 : REDLINE Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
ASTM D 2295 : 1996 : R2002 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
AASHTO MP 20 : 2013 : R2014 SPECIFICATION FOR STEEL-REINFORCED POLYETHYLENE (PE) RIBBED PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER
ASTM D 4351 : 1984 Test Method for Measuring the Thermal Conductivity of Plastics by the Evaporation-Calorimetric Method (Withdrawn 1990)
SAE AMS 3704 : 2016 ADHESIVE, CONTACT, POLYCHLOROPRENE (CR) RUBBER, RESIN MODIFIED
ASTM D 4969 : 2017 : REDLINE Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric
ASTM D 1525 : 2017 Standard Test Method for Vicat Softening Temperature of Plastics
NACE RP 06 90 : 2004 STANDARD FORMAT FOR COLLECTION AND COMPILATION OF DATA FOR COMPUTERIZED MATERIAL CORROSION RESISTANCE DATABASE INPUT
ASTM D 1562 : 2015 : REDLINE Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)
ASTM F 2307 : 2003 Standard Specification for Series 10 Poly(Vinyl Chloride) (PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter (Withdrawn 2011)
SAE AMS 3647 : 2015 POLYFLUOROETHYLENE PROPYLENE FILM AND SHEET
ASTM D 2235 : 2004 : R2011 Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
ASTM D 7194 : 2012 : REDLINE Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE)
ASTM D 707 : 2015 : REDLINE Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)
ASTM D 6691 : 2017 : REDLINE Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum
ASTM D 6272 : 2017 : REDLINE Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 3222 : 2005 : R2010 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 4065 : 2012 : REDLINE Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM F 2618 : 2015-11 SPECIFICATION FOR CHLORINATED POLY (VINYL CHLORIDE) (CPVC) PIPE AND FITTINGS FOR CHEMICAL WASTE DRAINAGE SYSTEMS
ASTM F 119 : 1982 : R1998 Standard Test Method for Rate of Grease Penetration of Flexible Barrier Materials (Rapid Method)
ASTM F 119 : 1982 : R2002 Standard Test Method for Rate of Grease Penetration of Flexible Barrier Materials (Rapid Method)
ASTM D 2282 : 1999 : R2005 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Withdrawn 2007)
ASTM D 6585 : 2017 : REDLINE Standard Specification for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape
ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
ASTM F 2854 : 2010 : R2016 Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing
ASTM D 6324 : 2011 : R2017 Standard Specification for Male Condoms Made from Polyurethane
ASTM D 5593 : 1999 : EDT 1 Standard Classification for Thermoplastic Elastomers-Olefinic (TEO) (Withdrawn 2005)
CSA C22.2 No. 62 : 1993 : R2013 SURFACE RACEWAY SYSTEMS
ASTM D 2513 : 2017-01 SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS
ASTM G 137 : 1997 : R2009 Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
ASTM D 2228 : 2004 Standard Test Method for Rubber Property-Relative Abrasion Resistance by the Pico Abrader Method
ASTM D 1621 : 2016 : REDLINE Standard Test Method for Compressive Properties of Rigid Cellular Plastics
ASTM D 1593 : 2013 : REDLINE Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
ASTM D 1776/D1776M : 2016 : REDLINE Standard Practice for Conditioning and Testing Textiles
ASTM D 1879 : 2006 Standard Practice for Exposure of Adhesive Specimens to Ionizing Radiation
ASTM D 1879 : 2006 : R2014 Standard Practice for Exposure of Adhesive Specimens to Ionizing Radiation
ASTM D 3679 : 2017 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
ASTM F 3034 : 2015 : REDLINE Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)
ASTM E 1027 : 1992 Practice for Exposure of Polymeric Materials to Ionizing Radiation (Withdrawn 1996)
ASTM D 4801 : 2008 : R2016 Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater
ASTM F 2922 : 2013 : R2018 Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers
ASTM D 2739 : 1997 : R2017 Standard Test Method for Volume Resistivity of Conductive Adhesives
ASTM D 4024 : 2015 : REDLINE Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
ASTM F 1282 : 2017 : REDLINE Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
ASTM D 4812 : 2011 : REDLINE Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics
ASTM F 1901 : 2016 : REDLINE Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems
ASTM D 5288 : 2014 : REDLINE Standard Test Method for Determining Tracking Index of Electrical Insulating Materials Using Various Electrode Materials (Excluding Platinum)
ASTM D 637 : 1990 Test Method for Surface Irregularities of Flat Transparent Plastic Sheets (Withdrawn 1995)
ASTM D 4477 : 2016 : REDLINE Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
ASTM D 5512 : 1996 Standard Practice for Exposing Plastics to a Simulated Compost Environment Using an Externally Heated Reactor (Withdrawn 2002)
ASTM D 6041 : 2011 Standard Specification for Contact-Molded <span class='unicode'>“</span>Fiberglass<span class='unicode'>”</span> (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
ASTM D 1712 : 2009 : R2014 Standard Practice for Resistance of Plastics to Sulfide Staining
ASTM D 2841 : 1994 Practice for Sampling Hollow Microspheres (Withdrawn 1999)
ASTM F 1987 : 2001 : R2011 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems (Withdrawn 2020)
ASTM D 1779 : 1998 : R2011 Standard Specification for Adhesive for Acoustical Materials
ASTM D 3090 : 1972 : R2008 Standard Practice for Storage Testing of Aerosol Products
ASTM F 667/F667M : 2016 : REDLINE Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings
ASTM F 1504 : 2014 : REDLINE Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation
ASTM PS 20 : 1995 Withdrawn 1997
ASTM F 2600 : 2009 : R2018 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM F 2905/F2905M : 2013 Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings and Joints For Oil and Gas Producing Applications
ASTM D 5721 : 2008 : R2013 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 3801 : 2010-08 TEST METHOD FOR MEASURING THE COMPARATIVE BURNING CHARACTERISTICS OF SOLID PLASTICS IN A VERTICAL POSITION
ASTM D 2444 : 2017 : REDLINE Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 7444 : 2011 Standard Practice for Heat and Humidity Aging of Oxidatively Degradable Plastics
ASTM D 5021 : 2000 Standard Specification for Thermoplastic Elastomer-Chlorinated Ethylene Alloy (TECEA) (Withdrawn 2007)
ASTM D 1527 : 1999 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80
ASTM D 4470:1997 Standard Test Method for Static Electrification
ASTM F 1871 : 2011-06 SPECIFICATION FOR FOLDED/FORMED POLY (VINYL CHLORIDE) PIPE TYPE A FOR EXISTING SEWER AND CONDUIT REHABILITATION
GOST 849:2018 Primary nickel. SpecificationsE
DIN EN 14617-13 E : 2013 AGGLOMERATED STONE - TEST METHODS - PART 13: DETERMINATION OF ELECTRICAL RESISTIVITY
UNE-EN 14617-13:2013 Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity
EN 14617-13:2013 Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity
ASTM F 2863 : 2011 Standard Specification for Central Vacuum Hose Inlet Valve Socket Dimensions
ASTM F 1864 : 2016 : REDLINE Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings
ASTM F 1412 : 2016 : REDLINE Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
ASTM D 4093 : 1995 : R2010 Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials
ASTM D 2739 : 1997 Standard Test Method for Volume Resistivity of Conductive Adhesives
ASTM D 3713 : 1995 Standard Test Method for Measuring Response of Solid Plastics to Ignition by a Small Flame (Withdrawn 2000)
ASTM D 2308 : 2007 : R2013 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM F 1803 : 2015 Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter
SAE J 2983 : 2012 RECOMMENDED PRACTICE FOR DETERMINING MATERIAL PROPERTIES OF LI-BATTERY SEPARATOR
L-P-392 Revision A:1964 PLASTIC MOLDING MATERIAL, ACETAL, INJECTION AND EXTRUSION
FM 1613 : 2017 POLYETHYLENE (PE) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE
ASTM D 2319/D2319M : 1998 : R2008e1 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 6867 : 2003 : R2009 Standard Specification for Perfluoroalkoxy (PFA)-Fluoropolymer Tubing
ASTM D 7705/D7705M : 2012 Standard Test Method for Alkali Resistance of Fiber Reinforced Polymer (FRP) Matrix Composite Bars used in Concrete Construction
MIL-M-24325 Base Document:1968 MOLDING MATERIAL PLASTIC, EPOXY COMPOUNDS THERMOSETTING
ASTM D 3678 : 2014 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions
ASTM D 4097 : 2001 : R2010 Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
ASTM D 1434 : 1982 : R2009 : EDT 1 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM F 2623 : 2015-01 SPECIFICATION FOR POLYETHYLENE OF RAISED TEMPERATURE (PE-RT) SDR 9 TUBING
ASTM F 1866 : 2018 : REDLINE Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings
MMM-A-1754 Base Document:1973 ADHESIVE AND SEALING COMPOUND EPOXY METAL FILLED
ASTM D 7472 : 2009 Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials
ASTM D 1788 : 1981 Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Plastics (Withdrawn 1988)
CSA Z245.20 SERIES : 2014 PLANT-APPLIED EXTERNAL COATINGS FOR STEEL PIPE
ASTM D 2739 : 1997 : R2010 Standard Test Method for Volume Resistivity of Conductive Adhesives
ASTM F 1614 : 1999 Standard Test Method for Shock Attenuating Properties of Materials Systems for Athletic Footwear
ASTM D 2307 : 2007A TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ACI 440R : 2007 REPORT ON FIBER-REINFORCED POLYMER (FRP) REINFORCEMENT FOR CONCRETE STRUCTURES
ASTM D 5024 : 2015 : REDLINE Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression
L-P-380 Revision C:1973 PLASTIC MOLDING MATERIAL METHACRYLATE
ASTM F 1697 : 2009 : R2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit
ASTM D 4475 : 2002 : R2016 Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By the Short-Beam Method
ASTM D 2578 : 2017 : REDLINE Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM F 2818:2010 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM D 3294 : 2015 : REDLINE Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes
ASTM D 6005 : 2003 : R2008 Standard Test Method for Determining Slump Resistance of Carpet Adhesives
MIL-L-50429 Revision A:1972 Laminate, Acetal and Cloth, (for Use with 81mm Ammunition)
ASTM D 3841 : 2016 : REDLINE Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
ASTM D 116 : 1986 : R2006 Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications
ASTM D 6005 : 2003 : R2009 Standard Test Method for Determining Slump Resistance of Carpet Adhesives
ASTM F 2433 : 2005 Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
MIL-I-21070 Revision B:1965 INSULATING SHEET AND TAPE, ELECTRICAL, REINFORCED MICA PAPER
ASTM D 5138 : 2016 : REDLINE Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)
ASTM F 1986 : 2001 : R2006 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems
ASTM D 5510 : 1994 Standard Practice for Heat Aging of Oxidatively Degradable Plastics
ASTM D 6110 : 2018 : REDLINE Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 3826 : 1998 : R2002 Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
NACE SP 06 90 : 2009 STANDARD FORMAT FOR COLLECTION AND COMPILATION OF DATA FOR COMPUTERIZED MATERIAL CORROSION RESISTANCE DATABASE INPUT
MIL R 60346 : C ROVING, GLASS, FIBROUS (FOR PREPREG TAPE & ROVING, FILAMENT WINDINGAND PULTRUSION APPLICATIONS)
MIL-I-24092 Revision D:1993 INSULATING VARNISHES AND SOLVENTLESS RESINS FOR APPLICATION BY THE DIP PROCESS
MIL-F-10336 Revision E:1977 FIBER SHEET, VULCANIZED
MIL-P-63462 Base Document:1979 PLASTIC MOLDING AND EXTRUSION MATERIAL, ETHYL CELLULOSE, FOR ROCKET GRAIN INHIBITING MATERIALS
ASTM D 5420 : 2016 : REDLINE Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 2307 : 2007A : R2013 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM D 4474 : 2000 Standard Classification System for Styrenic Thermoplastic Elastomer Injection Molding and Extrusion Materials (TES) (Withdrawn 2008)
ASTM D 4635 : 2016 : REDLINE Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications
ASTM D 116 : 1986 : R2011 Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications
ASTM D 3030 : 2017 : REDLINE Standard Test Method for Volatile Matter (Including Water) of Vinyl Chloride Resins
ASTM D 2289 : 1984 Method of Test for Tensile Properties of Plastics at High Speeds (Withdrawn 1990)
ASTM D 1003 : 2013 : REDLINE Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM F 2807 : 2013 : R2018 Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications
ASTM F 1697:2009 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit <a href="#fn00002"></a>
ASTM F 2468 : 2005 Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications
ASTM D 2294 : 1996 : R2016 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM F 2806 : 2010 : R2015 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR)
B184 SERIES-17 Polymeric subsurface stormwater management structures
ASTM D 1434 : 1982 : R2003 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
MIL-C-44304 Revision A:1993 CLOTH, COATED AND LAMINATED, CHEMICAL PROTECTIVE
ASTM D 2307 : 2007 : R2013 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
MIL-I-24391 Revision C:1990 INSULATION TAPE, ELECTRICAL, PLASTIC, PRESSURE SENSITIVE
L-P-389 Revision A:1964 PLASTIC MOLDING MATERIAL, FEP FLUOROCARBON, MOLDING AND EXTRUSION
BS ISO 15840:2004 Ships and marine technology. Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications
ASTM D 2765 : 2016 : REDLINE Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
ASTM G 137 : 1997 : R2017 Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
NFPA 263 : 1994 METHOD OF TEST FOR HEAT AND VISIBLE SMOKE RELEASE RATES FOR MATERIALS AND PRODUCTS
ASTM F 2390:2012 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content
CSA A440 : 2017 NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS
ASTM D 2301 : 2010 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
AASHTO M 304 : 2011 SPECIFICATION FOR POLY(VINYL CHLORIDE) (PVC) PROFILE WALL DRAIN PIPE AND FITTINGS BASED ON CONTROLLED INSIDE DIAMETER
ASTM D 2288 : 1997 : R2001 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
SAE AMS P 46112 : 2002(S2015) PLASTIC SHEET AND STRIP, POLYIMIDE
ASTM D 955 : 2008 : R2014 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
ASTM D 817 : 2012 : REDLINE Standard Test Methods of Testing Cellulose Acetate Propionate and Cellulose Acetate Butyrate
ASTM D 2292 : 1985 Recommended Practice for Compression Molding Test Specimens of Styrene-Butadiene Molding and Extrusion Materials (Withdrawn 1992)
ASTM G 137 : 1997 Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
ASTM D 2301 : 2010 : R2017 TEST METHOD FOR WEIGHT LOSS OF PLASTICIZERS ON HEATING
ASTM F 2648/F2648M : 2017 : REDLINE Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications
NACE TM 02 98 : 2015 EVALUATING THE COMPATIBILITY OF FRP PIPE AND TUBULARS WITH OILFIELD ENVIRONMENTS
SAE J 3021 : 2014 RECOMMENDED PRACTICE FOR DETERMINING MATERIAL PROPERTIES OF LI-BATTERY CATHODE ACTIVE MATERIALS
ANSI/AWWA D120 : 2009 THERMOSETTING FIBERGLASS-REINFORCED PLASTIC TANKS
ASTM D 3914 : 2002 : R2016 Standard Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod
ASTM D 3035 : 2015 : REDLINE Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
AASHTO M 294 : 2015 SPECIFICATION FOR CORRUGATED POLYETHYLENE PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER
ASTM D 3020 : 1989 Specification for Polyethylene and Ethylene Copolymer Plastic Sheeting for Pond, Canal and Reservoir Lining (Withdrawn 1996)
ASTM D 706 : 2015 : REDLINE Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)
ASTM D 1004 : 2013 : REDLINE Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D 2996 : 2017 : REDLINE Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 3369 : 2001 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Cast Film (Withdrawn 2006)
ASTM D 5990 : 2000 Standard Classification System for Polyketone Injection Molding and Extrusion Materials (PK) (Withdrawn 2007)
ASTM F 1986 : 2001 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems
ASTM F 1987 : 2001 : R2006 Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems
ASTM F 2881/F2881M : 2018 Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
ASTM D 1925 : 1970 TEST METHOD FOR YELLOWNESS INDEX OF PLASTICS
CSA C22.2 No. 62 : 1993 SURFACE RACEWAY SYSTEMS
ASTM F 810 : 2012 : R2018 Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields
ASTM D 5169 : 1998 : R2004 Standard Test Method for Shear Strength (Dynamic Method) of Hook and Loop Touch Fasteners
ASTM D 2739 : 1997 : R2004 Standard Test Method for Volume Resistivity of Conductive Adhesives
ASTM D 2442 : 1975 : R2007 Standard Specification for Alumina Ceramics for Electrical and Electronic Applications
ASTM F 2953 : 2012 Standard Specification for Phenolic Raw Materials for the Use in Bearing Cages
ASTM F 119 : 1982 : R2008 Standard Test Method for Rate of Grease Penetration of Flexible Barrier Materials (Rapid Method)
ASTM E 1420 : 1991 Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996)
ASTM F 2160 : 2016 Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)
ASTM F 119 : 1982 : R2015 Standard Test Method for Rate of Grease Penetration of Flexible Barrier Materials (Rapid Method)
ASTM D 494 : 2011 : REDLINE Standard Test Method for Acetone Extraction of Phenolic Molded or Laminated Products
ASTM D 2729 : 2017 Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
ASTM D 2241 : 2015 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
ASTM F 2435 : 2015 : REDLINE Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe
ASTM D 3309 : 1996 : REV A : R2002 Standard Specification for Polybutylene (PB) Plastic Hot- and Cold-Water Distribution Systems (Withdrawn 2010)
ASTM D 785 : 2008 Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
ASTM D 2105 : 2001 : R2014 Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM F 891 : 2016 : REDLINE Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core
ASTM D 2235 : 2004 Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
ASTM F 2947/F2947M : 2014-03 SPECIFICATION FOR 150 TO 1500 MM [6 TO 60 IN.] ANNULAR CORRUGATED PROFILE-WALL POLYETHYLENE (PE) PIPE AND FITTINGS FOR SANITARY SEWER APPLICATIONS
ASTM D 3916 : 2008 : R2016 Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced<brk /> Plastic Rod
ASTM D 2582 : 2016 : REDLINE Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 2442 : 1975 : R2016 Standard Specification for Alumina Ceramics for Electrical and Electronic Applications
ASTM D 5948 : 2005 : EDT 1 Standard Specification for Molding Compounds, Thermosetting
ASTM F 1673 : 2010 : R2016 Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems
ASTM F 2806 : 2010 : EDT 1 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR)
ASTM F 3131 : 2014 Standard Specification for Epoxy / Cotton Raw Materials for the Use in Bearing Cages
ASTM F 758 : 2014 : REDLINE Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage
ASTM D 1870 : 1991 Practice for Elevated Temperature Aging Using a Tubular Oven (Withdrawn 1998)
ASTM D 2447 : 2003 Standard Specification for Polyethylene (PE) Plastic Pipe, Schedules 40 and 80, Based on Outside Diameter (Withdrawn 2010)
ASTM D 3846 : 2008 : R2015 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics (Withdrawn 2024)
ASTM F 2986 : 2012 : R2017 Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications
ASTM D 1043 : 2016 : REDLINE Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test
ASTM F 2829/F2829M : 2015 : REDLINE Standard Specification for Metric- and Inch-Sized Crosslinked Polyethylene (PEX) Pipe Systems
ASTM D 7211 : 2013-05 SPECIFICATION FOR PARTS MACHINED FROM POLYCHLOROTRIFLUOROETHYLENE (PCTFE) AND INTENDED FOR GENERAL USE
ASTM D 5170 : 1998 : R2010 Standard Test Method for Peel Strength ("T" Method) of Hook and Loop Touch Fasteners
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 6054 : 1997 : R2004 Standard Practice for Conditioning Electrical Insulating Materials for Testing (Withdrawn 2012)
ASTM G 125 : 2000 Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants
ASTM D 1242 : 1995 : REV A Standard Test Methods for Resistance of Plastic Materials to Abrasion (Withdrawn 2004)
ASTM D 7774 : 2017 : REDLINE Standard Test Method for Flexural Fatigue Properties of Plastics
ASTM D 2741 : 1995 : R2005 Standard Test Method for Susceptibility of Polyethylene Bottles to Soot Accumulation (Withdrawn 2011)
ASTM F 791 : 1996 : R2002 : EDT 1 Standard Test Method for Stress Crazing of Transparent Plastics
ASTM D 756 : 1993 Practice for Determination of Weight and Shape Changes of Plastics Under Accelerated Service Conditions (Withdrawn 1998)
ASTM D 4475 : 2002 Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By The Short-Beam Method
ASTM D 1693 : 2015 : REDLINE Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 6003 : 1996 Standard Test Method for Determining Weight Loss From Plastic Materials Exposed to Simulated Municipal Solid-Waste (MSW) Aerobic Compost Environment (Withdrawn 2005)
ASTM D 7791 : 2017 : REDLINE Standard Test Method for Uniaxial Fatigue Properties of Plastics
ASTM F 794 : 2003 : R2009 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter
ASTM D 6325 : 1998 : R2011 Test Method for Determining Open Assembly Time of Carpet Mastic Adhesives
NSF 8 : 2017 COMMERCIAL POWERED FOOD PREPARATION EQUIPMENT
BS EN 14617-13:2013 Agglomerated stone. Test methods Determination of electrical resistivity
DIN EN 14617-13:2013-06 Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity

ASTM D 709 : 2017 : REDLINE Standard Specification for Laminated Thermosetting Materials
ASTM D 756 : 1993 Practice for Determination of Weight and Shape Changes of Plastics Under Accelerated Service Conditions (Withdrawn 1998)
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
ASTM E 104 : 2002 Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.