• There are no items in your cart

ASTM D 2513 : 2017-01

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS
Superseded date

09-17-2019

Published date

01-01-2017

CONTAINED IN VOL. 08.04, 2017 Defines requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications.

Committee
F 17
DevelopmentNote
Supersedes ASTM F 678. (10/2001)
DocumentType
Redline
PublisherName
American Society for Testing and Materials
Status
Superseded

API RP 1177 : 2017 RECOMMENDED PRACTICE FOR STEEL PIPELINE CONSTRUCTION QUALITY MANAGEMENT SYSTEMS
ASTM D 2683 : 2014 : REDLINE Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
ASTM F 905 : 2004 Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
ASTM F 2145 : 2013 : R2018 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM F 1588 : 1996 : R2002 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM F 689 : 1997 : R2011 Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings (Withdrawn 2017)
ASTM F 2634 : 2015 : REDLINE Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method
ASTM F 2818 : 2010 : R2014 : EDT 1 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM F 905 : 2004 : R2018 Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
ASTM F 1973 : 2013 : EDT 1 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
API 15S : 2016 SPOOLABLE REINFORCED PLASTIC LINE PIPE
ASTM F 1588 : 1996 : R2011 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM F 2818 : 2010 : R2014 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM F 1973 : 2013 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM F 2880 : 2014 : REDLINE Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in.
NFPA 54 : 2018 NATIONAL FUEL GAS CODE
NFPA 501A : 2017 FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES, AND COMMUNITIES
ICC 2009 INT. RESI.CODE & COMM.-I1 : 2009 2009 INTERNATIONAL RESIDENTIAL CODE & COMMENTARY - VOLUME 2: CHAPTERS 12 TO 44
ANSI Z223.1 : 2018 NATIONAL FUEL GAS CODE
ASTM F 2600 : 2009 : R2013 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM F 1041 : 2002 Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing
ASTM F 689 : 1997 : R2004 Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings
ASTM F 1948 : 2015 : REDLINE Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing
ASTM F 1563 : 2001 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 1563 : 2001 : R2011 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 1804 : 2008 : R2012 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
ASTM F 1563 : 2001 : R2007 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 1733 : 2013 : REDLINE Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM F 1962 : 2011 : REDLINE Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings
ASTM F 1056 : 2018 : REDLINE Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings
ASTM F 2830 : 2011 : R2017 Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
ASTM F 1041 : 2002 : R2016 Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing
ASTM F 1924 : 2012 : REDLINE Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
ASTM F 2896 : 2011 : R2017 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
NFPA 58 : 2017 LIQUEFIED PETROLEUM GAS CODE
ISO 22621-1:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 1: General
ASME B31.8 : 2016 Gas Transmission and Distribution Piping Systems
ASME B31.3:2016 PROCESS PIPING
ASTM F 689 : 1997 Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings
05/30130524 DC : DRAFT MAR 2005 ISO 22621-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 1: GENERAL
06/30146370 DC : DRAFT SEP 2006 ISO 15439-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 4 BAR - POLYAMIDE (PA) - PART 1: GENERAL
API 15LE : 2008 : R2013 SPECIFICATION FOR POLYETHYLENE LINE PIPE (PE)
ASTM F 905 : 2004 : R2011 Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
API 15LE CHINESE : 2008 SPECIFICATION FOR POLYETHYLENE LINE PIPE (PE)
CSA B137 COMPENDIUM : 2017 THERMOPLASTIC PRESSURE PIPING COMPENDIUM
AWWA C906:2015 POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS
ASTM F 1804 :2008 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
ASTM F 2145 : 2013 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM F 2600 : 2009 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM F 1588 : 1996 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM F 1041 : 2002 : R2008 Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing
ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 IRC® Code and Commentary, Volume 2
ICC IFGC CODE AND COMMENTARY : 2015 IFGC® Code and Commentary
ICC 2012 INTERNATIONAL FUEL GAS CODE : 2012 INTERNATIONAL FUEL GAS CODE
ICC 2012 INTERNATIONAL RESI. CODE : 2012 INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS
ASTM F 2509 : 2015-12 SPECIFICATION FOR FIELD-ASSEMBLED ANODELESS RISER KITS FOR USE ON OUTSIDE DIAMETER CONTROLLED POLYETHYLENE GAS DISTRIBUTION PIPE AND TUBING
MSS SP 142 : 2012 EXCESS FLOW VALVES FOR FUEL GAS SERVICE, NPS 1[1/2] THROUGH 12
CSA C448 SERIES : 2016 DESIGN AND INSTALLATION OF GROUND SOURCE HEAT PUMP SYSTEMS FOR COMMERCIAL AND RESIDENTIAL BUILDINGS
MSS SP 131 : 2017 METALLIC MANUALLY OPERATED GAS DISTRIBUTION VALVES
MSS SP 115 : 2017 EXCESS FLOW VALVES, NPS 1[1/4] AND SMALLER, FOR FUEL GAS SERVICE
ASTM F 2818:2010 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM F 1973 : 2013 : R2018 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM F 2600 : 2009 : R2018 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ISO 15439-1:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) Polyamide (PA) Part 1: General
ANSI/CSA-B149.6-15 Code for digester gas, landfill gas, and biogas generation and utilization
ASTM F 2830 : 2011 Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
API 15LE : 2008(R2018) SPECIFICATION FOR POLYETHYLENE LINE PIPE (PE)
ASTM F 1588 : 1996 : R2015 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ISO/TS 18226:2006 Plastics pipes and fittings — Reinforced thermoplastics pipe systems for the supply of gaseous fuels for pressures up to 4 MPa (40 bar)
NSF 14 : 2016 PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS
ASTM F 2619/F2619M : 2013 : REDLINE Standard Specification for High-Density Polyethylene (PE) Line Pipe
ASTM F 2896 : 2011 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
ASTM F 1588 : 1996 : R2007 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM F 1804 : 2008 : R2016 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
ASTM F 1055 : 2016-09 SPECIFICATION FOR ELECTROFUSION TYPE POLYETHYLENE FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYETHYLENE AND CROSSLINKED POLYETHYLENE (PEX) PIPE AND TUBING
ICC 2012 INTERNATIONAL MECH. CODE : 2012 INTERNATIONAL MECHANICAL CODE

MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 2774 : 2012 : REDLINE Standard Practice for Underground Installation of Thermoplastic Pressure Piping
NFPA 58 : 2017 LIQUEFIED PETROLEUM GAS CODE
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
MIL-STD-1235 Revision C:1988 SINGLE AND MULTILEVEL CONTINUOUS SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES FUNCTIONAL CURVES OF THE CONTINUOUS SAMPLING PLANS
ASME B31.8 : 2016 Gas Transmission and Distribution Piping Systems
ASTM D 1238 : 2013 : REDLINE Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
ASTM D 1435 : 2013 : REDLINE Standard Practice for Outdoor Weathering of Plastics
ASTM D 2683 : 2014 : REDLINE Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
FED-STD-123 Revision H:2007 MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM F 2619/F2619M : 2013 : REDLINE Standard Specification for High-Density Polyethylene (PE) Line Pipe
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM G 155 : 2013 : REDLINE Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
ASTM F 1055 : 2016-09 SPECIFICATION FOR ELECTROFUSION TYPE POLYETHYLENE FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYETHYLENE AND CROSSLINKED POLYETHYLENE (PEX) PIPE AND TUBING
ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
CFR 49(PTS178-199) : OCT 2017 TRANSPORTATION
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2565 : 2016 : REDLINE Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
ISO 4437:2007 Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.