ASTM D 790 : 2017 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
English
07-01-2017
CONTAINED IN VOL. 08.01, 2017 Defines test methods which are used to determine the flexural properties of unreinforced and reinforced plastics, including highmodulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to simply supported beam (specimen).
Committee |
D 20
|
DevelopmentNote |
Supersedes ASTM D 650. (02/2002)
|
DocumentType |
Redline
|
Pages |
16
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
1.1These test methods are used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (specimen). The method is generally applicable to both rigid and semi-rigid materials, but flexural strength cannot be determined for those materials that do not break or yield in the outer surface of the test specimen within the 5.0 % strain limit.
1.2Test specimens of rectangular cross section are injection molded or, cut from molded or extruded sheets or plates, or cut from molded or extruded shapes. Specimens must be solid and uniformly rectangular. The specimen rests on two supports and is loaded by means of a loading nose midway between the supports.
1.3Measure deflection in one of two ways; using crosshead position or a deflectometer. Please note that studies have shown that deflection data obtained with a deflectometer will differ from data obtained using crosshead position. The method of deflection measurement shall be reported.
Note 1:Requirements for quality control in production environments are usually met by measuring deflection using crosshead position. However, more accurate measurement may be obtained by using an deflection indicator such as a deflectometer.
Note 2:Materials that do not rupture by the maximum strain allowed under this test method may be more suited to a 4-point bend test. The basic difference between the two test methods is in the location of the maximum bending moment and maximum axial fiber stresses. The maximum axial fiber stresses occur on a line under the loading nose in 3-point bending and over the area between the loading noses in 4-point bending. A four-point loading system method can be found in Test Method D6272.
1.4The values stated in SI units are to be regarded as the standard. The values provided in parentheses are for information only.
1.5The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 3:This standard and ISO 178 address the same subject matter, but differ in technical content.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standards | Relationship |
UNE 53189-3:1977 | Identical |
BS DD140-2(1987) : 1987 | WALL TIES - RECOMMENDATIONS FOR DESIGN OF WALL TIES |
MIL-C-47224 Revision B:1993 | COMPOUND, MOLDING, TRANSFER, EPOXY RESIN, SINGLE COMPONENT |
MIL-R-83330 Base Document:1971 | RESIN, HEAT RESISTANT, LAMINATING |
MIL-V-22272 Revision D:1982 | VISORS, NEODYMIUM LASER, PROTECTIVE FOR AIRCREWMAN'S HELMET |
15/30287229 DC : 0 | BS EN ISO 80369-1 - SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
MIL-P-43038 Revision B:1973 | PLASTIC MOLDING MATERIAL, POLYESTER, LOW PRESSURE LAMINATING, HIGH TEMPERATURE RESISTANT |
AAMI ISO 80369-1 : 2010 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
07/30164614 DC : 0 | BS EN 15546-2 - SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 2: CONNECTORS FOR RESPIRATORY APPLICATIONS |
CSA N285.5 : 2013 | PERIODIC INSPECTION OF CANDU NUCLEAR POWER PLANT CONTAINMENT COMPONENTS |
CTI STD 131 : 2009 | FIBERGLASS-REINFORCED PLASTIC PANELS |
L-P-535 Revision E:1979 | PLASTIC SHEET (SHEETING): PLASTIC STRIP: POLY(VINYL CHLORIDE) AND POLY(VINYL CHLORIDE-VINYL ACETATE), RIGID |
ANSI/AAMI/ISO 80369-3:2016 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 3: CONNECTORS FOR ENTERAL APPLICATIONS |
IEEE 1133-1988 | IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications |
MIL-P-25518 Revision B:1981 | Plastic Materials, Silicone Resin, Glass Fiber Base, Low Pressure Laminated |
AASHTO LRFDLTS 1 : 1900 | LRFD SPECIFICATIONS FOR STRUCTURAL SUPPORTS FOR HIGHWAY SIGNS, LUMINAIRES, AND TRAFFIC SIGNALS |
MIL-DTL-24191 Revision D:1996 | PLASTIC SHEET, CELL OR CONTINUOUS CAST, ACRYLIC, SHIPBOARD APPLICATION (ILLUMINATION AND SIGNAL LIGHTING) |
BS EN ISO 17348:2016 | Petroleum and natural gas industries. Materials selection for high content CO<sub>2</sub> environment for casings, tubings and downhole equipment |
SAE AMS3847D | Cloth, Quartz, \"B\" Stage Polyimide Resin Impregnated Style 581 Fabric, 315 °C (599 °F) |
CGSB 12.12 : M90 | PLASTIC SAFETY GLAZING SHEETS |
MIL-R-82483 Revision A:1976 | RESIN, POLYESTER, SOLUTIONS |
15/30321951 DC : 0 | BS ISO 20195 - STANDARD PRACTICE - GUIDE FOR DESIGN FOR ADDITIVE MANUFACTURING |
MIL-H-53096 Base Document:1990 | HOSES & HOSE ASSEMBLIES, ELASTOMER, RUBBER, LIQUID FUEL, NON-COLLAPSIBLE, LOW TEMPERATURE |
MIL-PRF-46197 Revision A:1997 | LAMINATE: HIGH-STRENGTH GLASS, FABRIC-REINFORCED, POLYESTER RESIN PREIMPREGNATED |
MIL-M-48245 Revision B:1988 | MOLDING COMPOUND, HOUSING |
MIL-A-47318 Revision A:1990 | ADHESIVE, COPOLYMER POLYURETHANE |
ASTM D 5476 : 1999 | Standard Classification System for Thermoplastic Polyurethane Materials (TPU) (Withdrawn 2005) |
16/30338304 DC : 0 | BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS |
ASTM F 624 : 2009 : R2015 : EDT 1 | Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications |
MIL-P-46122 Revision B:1975 | PLASTIC MOLDING MATERIAL AND PLASTIC EXTRUSION MATERIAL, POLYVINYLIDENE FLUORIDE POLYMER AND COPOLYMER |
NACE TM 01 96 : 0 | CHEMICAL RESISTANCE OF POLYMERIC MATERIALS BY PERIODIC EVALUATION |
ASTM D 3615 : 1987 | Test Method for Chemical Resistance of Thermoset Molding Compouds Used in the Manufacture of Molded Fittings (Withdrawn 1993) |
ASTM D 5948 : 2005 | Standard Specification for Molding Compounds, Thermosetting |
MIL-P-46185 Base Document:1983 | PLASTIC MOLDING & EXTRUSION MATERIALS, POLYETHERSULFONE |
AWWA M55 : 1 | PE PIPE - DESIGN AND INSTALLATION |
MIL-DTL-32378 Base Document:2012 | LAMINATE: UNIDIRECTIONAL, REINFORCED, CROSS-PLIED, ARAMID FIBER, PLASTIC ARMOR MATERIAL |
MIL-P-43043 Revision C:1978 | PLASTIC MOLDING MATERIAL, PRE-MIX, POLYESTER, GLASS FIBER REINFORCED |
03/312144 DC : DRAFT JULY 2003 | ISO 13628-10 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 10 - BONDED FLEXIBLE PIPE |
ASTM D 1201 : 2013 : REDLINE | Standard Specification for Thermosetting Polyester Molding Compounds |
SAE AMS3894/17B | Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 200 (1379) Tensile, 18.0 (124) Modulus, 120 (248) |
SAE AMS3644G | Plastic: Polyimide For Molded Rod, Bar, and Tube, Plaque, and Formed Parts |
API 1631 : 2001 | INTERIOR LINING AND PERIODIC INSPECTION OF UNDERGROUND STORAGE TANKS |
ASTM C 582 : 2009 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
SAE AMS3867C | Boron Filament Tape, Epoxy-Resin-Impregnated |
MIL-O-71039 Base Document:1992 | OBTURATING BAND, PLASTIC SPLIT |
CSA B66 : 2016 | DESIGN, MATERIAL, AND MANUFACTURING REQUIREMENTS FOR PREFABRICATED SEPTIC TANKS AND SEWAGE HOLDING TANKS |
ASTM D 3222 : 2005 : R2015 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
I.S. EN ISO 17348:2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - MATERIALS SELECTION FOR HIGH CONTENT CO[2] ENVIRONMENT FOR CASINGS, TUBINGS AND DOWNHOLE EQUIPMENT (ISO 17348:2016) |
PREN 1825-1 : DRAFT 1995 | INSTALLATIONS FOR SEPARATION OF GREASE - PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
ASTM E 2639 : 2012 : R2018 | Standard Test Method for Blast Resistance of Trash Receptacles |
UNI CEI EN ISO 80369-1 : 2011 | SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
SAE J1568_201204 | Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders |
ASTM F 755 : 1999 : EDT 1 | Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants |
AAMI CN6 : 2015 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 6: CONNECTORS FOR NEURAXIAL APPLICATIONS |
SAE J1774_201006 | Design Guidelines for Fiberboard Materials |
ASTM C 1486 : 2018 : REDLINE | Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings |
ASTM F 2881 : 2011 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
UNE-EN ISO 80369-6:2016 | Small bore connectors for liquids and gases in healthcare applications - Part 6: Connectors for neuraxial applications (ISO 80369-6:2016, Corrected version 2016-11-15) |
ISO 80369-1:2010 | Small-bore connectors for liquids and gases in healthcare applications Part 1: General requirements |
ASTM E 1434 : 2000 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
NACE RP 03 04 : 2004 | DESIGN, INSTALLATION, AND OPERATION OF THERMOPLASTIC LINERS FOR OILFIELD PIPELINES |
SAE AMS3670/1B | UNFILLED POLYAMIDE-IMIDE BAR, ROD, AND SHAPES |
ASTM F 2599 : 2016 : REDLINE | Standard Practice for The Sectional Repair of Damaged Pipe By Means of An Inverted Cured-In-Place Liner |
ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
ASTM F 2881 : 2011 : R2015 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
ASTM D 4549 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS) |
ASTM D 2952 : 1995 | Specification for Ethylene Plastics (Withdrawn 1999) |
ASTM D 705 : 1999 : R2012 | Standard Specification for Urea-Formaldehyde Molding Compounds |
ASTM C 722 : 2004 | Standard Specification for Chemical-Resistant Monolithic Floor Surfacings |
ASTM F 641 : 2009 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
CSA C22.2 No. 0.17 : 2000 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
ASTM C 647 : 2008 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
ASTM D 705 : 1999 : R2004 | Standard Specification for Urea-Formaldehyde Molding Compounds |
ASTM E 2771 : 2011 : EDT 1 | Standard Terminology for Homeland Security Applications |
ASTM D 706 : 2015 : REDLINE | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
ASTM D 6856/D6856M : 2003 : R2008 : EDT 1 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM D 1039 : 2016 : REDLINE | Standard Test Methods for Glass-Bonded Mica Used as Electrical Insulation |
ASTM F 736 : 2017 : REDLINE | Standard Test Method for Impact Resistance of Monolithic Polycarbonate Sheet by Means of a Falling Weight |
ASTM D 705 : 1999 | Standard Specification for Urea-Formaldehyde Molding Compounds |
ASTM D 3489 : 2017 : REDLINE | Standard Test Methods for Microcellular Urethane Materials |
ASTM F 1606 : 2005 : R2014 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner |
BS EN ISO 13628-2:2006 | Petroleum and natural gas industries. Design and operation of subsea production systems Unbonded flexible pipe systems for subsea and marine applications |
ISO 80369-3:2016 | Small-bore connectors for liquids and gases in healthcare applications — Part 3: Connectors for enteral applications |
AWWA M45 : 3 | FIBERGLASS PIPE DESIGN |
AA-R-200 Revision F:1987 | REFRIGERATOR, MECHANICAL, COMMERCIAL, SELF-CONTAINED, REACH-IN AND PASS-THROUGH |
MIL-M-24519 Revision E:1992 | MOLDING PLASTICS, POLYESTER AND POLYARYLETHER THERMOPLASTIC |
MIL P 46169 : A | PLASTIC, SHEET MOLDING COMPOUND, POLYESTER, GLASS FIBER REINFORCED (FOR GENERAL PURPOSE APPLICATIONS) |
MIL-P-46179 Revision A:1986 | PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYAMIDE IMIDE |
MIL-M-14 Revision H:1990 | MOLDING COMPOUNDS, THERMOSETTING |
MIL-P-46161 Revision A:1976 | PLASTIC MOLDING MATERIAL, POLYTEREPHTHALATE THERMOPLASTIC, GLASS FIBER REINFORCED |
MIL-C-47221 Revision A:1982 | COMPOUND, MOLDING, EPOXY RESIN, SILICON DIOXIDE AND ASBESTOS FIBER FILL |
MIL-P-46847 Revision B:1984 | PLASTIC MATERIAL, FOAMED POLYURETHANE FOR ENCAPSULATING ELECTRONIC COMPONENTS |
API SPEC 11D1 : 2015 | PACKERS AND BRIDGE PLUGS |
09/30173644 DC : 0 | BS EN ISO 80369-1 - SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
CSA S808 : 2014 | SPECIFICATION FOR FIBRE-REINFORCED POLYMER (FRP) MATERIALS FOR EXTERNALLY REINFORCING STRUCTURES |
I.S. EN ISO 12086-2:2006 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
MIL-M-19417 Revision D:1992 | Mask Assemblies, Oxygen and Smoke, Full Face |
ASTM E 2771 : 2011 : R2019 | Standard Terminology for Homeland Security Applications |
SAE AMS3906C | Glass Tape and Flat Sheet, Non-Woven Cloth Epoxy Resin Impregnated, For Hand and Machine Layup |
ASTM D 2990 : 2017 : REDLINE | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
SAE AMS3733C | Potting Compound, Epoxy Two Part, Highly Filled, Heat Cure, High Compressive Strength |
I.S. EN ISO 80369-6:2016 | SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 6: CONNECTORS FOR NEURAXIAL APPLICATIONS (ISO/IEC/DIS 80369-6:2014) |
ASTM D 5948 : 2005 : R2012 | Standard Specification for Molding Compounds, Thermosetting |
SAE AMS3670B | Polyamide-Imide Bar, Rod, and Shapes Molded or Extruded |
CSA S807 : 2010 : R2015 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
CSA S807 : 2010 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
SAE AMS3826C | Cloth, Type “E” Glass “B” Stage Polyester Resin Impregnated 1581 and 7781 Type Fabric |
UNE-EN ISO 80369-1:2011 | Small bore connectors for liquids and gases in healthcare applications - Part 1: General requirements (ISO 80369-1:2010) |
API SPEC 12P : 2016 | SPECIFICATION FOR FIBERGLASS REINFORCED PLASTIC TANKS |
15/30288418 DC : 0 | BS EN ISO 80369-2 - SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 2: CONNECTORS FOR BREATHING SYSTEMS AND DRIVING GASES APPLICATIONS |
MIL B 17901 : B | BEARING COMPONENTS, BONDED SYNTHETIC RUBBER, WATER LUBRICATED |
A-A-52446 Base Document:1994 | SHEET MOLDING COMPOUND: LOW SHRINKAGE (METRIC) |
AASHTO M 330 : 2013 | SPECIFICATION FOR POLYPROPYLENE PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
14/30292519 DC : 0 | BS EN 80369-5 ED 1.0 - SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 5: CONNECTORS FOR LIMB CUFF INFLATION APPLICATIONS |
CSA C22.2 No. 0.17 : 2000 : R2013 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
BS ISO 12891-2:2014 | Retrieval and analysis of surgical implants Analysis of retrieved surgical implants |
ASTM D 4617 : 2003 | Standard Classification System for Phenolic Compounds (PF) (Withdrawn 2012) |
CEI EN 80369-5 : 1ED 2017 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 5: CONNECTORS FOR LIMB CUFF INFLATION APPLICATIONS |
ASTM D 1562 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
ASTM F 755 : 1999 : R2005 | Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants |
ASTM D 3929 : 2003 | Standard Test Method for Evaluating Stress Cracking of Plastics by Adhesives Using the Bent-Beam Method |
ASTM C 722 : 2004 : R2012 | Standard Specification for Chemical-Resistant Monolithic Floor Surfacings |
SAE AMS3845C | Cloth, Type “E” Glass “B” Stage Addition Cure Polyimide-Resin-Impregnated |
ASTM D 704 : 1999 | Standard Specification for Melamine-Formaldehyde Molding Compounds |
ASTM F 635 : 1985 : R1991 | Guide for Selection of Tests for Material Properties of Liquid Thermoset Encapsulating Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996) |
API 17L1 : 2013 | SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT |
MIL-DTL-64154 Revision B:2008 | LAMINATE: FIBERGLASS-FABRIC-REINFORCED, PHENOLIC |
ASTM D 794 : 1993 | Practice for Determining Permanent Effect of Heat on Plastics (Withdrawn 1998) |
ISO 80369-6:2016 | Small bore connectors for liquids and gases in healthcare applications — Part 6: Connectors for neuraxial applications |
I.S. EN ISO 80369-7:2017 COR 2017 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS (ISO 80369-7:2016, CORRECTED VERSION 2016-12-01) |
UNI CEN ISO/TS 24817 : 2011 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
ANSI/AWWA D120 : 2009 | THERMOSETTING FIBERGLASS-REINFORCED PLASTIC TANKS |
ANSI Z80.6 : 1983 | PHYSICOCHEMICAL PROPERTIES OF CONVENTIONAL HARD PLASTIC CONTACT LENSES, |
ANSI/AWWA C514 : 2015 | AIR VALVE AND VENT INFLOW PREVENTER ASSEMBLIES FOR POTABLE WATER DISTRIBUTION SYSTEM AND STORAGE FACILITIES |
I.S. EN ISO 80369-3:2016 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 3: CONNECTORS FOR ENTERAL APPLICATIONS (ISO/IEC/DIS 80369-3:2014) |
ASTM D 4097 : 2001 | Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks |
CEI UNI EN ISO 80369-1 : 2011 | SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
ASTM D 6713 : 2014 : REDLINE | Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) |
ASTM E 2740 : 2012 : R2018 | Standard Specification for Trash Receptacles Subjected to Blast Resistance Testing |
ASTM D 6098 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC) |
AWWA F101 : 2013 | CONTACT-MOLDED, FIBERGLASS-REINFORCED PLASTIC WASH-WATER TROUGHS AND LAUNDERS |
SAE AMS3619E | Resin, Polyimide, Laminating High Temperature Resistant, 315 °C (599 °F) |
ASTM D 704 : 1999 : R2012 | Standard Specification for Melamine-Formaldehyde Molding Compounds |
ASTM D 4021 : 1992 | Standard Specification for Glass-Fiber-Reinforced Polyester Underground Petroleum Storage Tanks (Withdrawn 1999) |
BS EN ISO 80369-6:2016 | Small bore connectors for liquids and gases in healthcare applications Connectors for neuraxial applications |
ASTM D 3754 : 2014 : REDLINE | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe |
ASTM F 1251 : 1989 : R1995 | Standard Terminology Relating to Polymeric Biomaterials in Medical and Surgical Devices |
ASTM F 790 : 2008 : R2013 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
ASTM F 2150 : 2013 : REDLINE | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Tissue-Engineered Medical Products |
ASTM C 647 : 2008 : R2013 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
ASTM F 2502 : 2017 : REDLINE | Standard Specification and Test Methods for Absorbable Plates and Screws for Internal Fixation Implants |
(INACTIVE RECORD)ASTM D 5336 : 2015-04 | CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPHTHALAMIDE (PPA) INJECTION MOLDING MATERIALS |
ASTM E 1309 : 2000 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM D 6856 : 2003 : R2008 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM D 4067 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
ASTM F 1216 : 2016 : REDLINE | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube |
ASTM E 2740 : 2012 | Standard Specification for Trash Receptacles Subjected to Blast Resistance Testing |
ASTM D 3222 : 2005 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
ASTM D 6262 : 2017 : REDLINE | Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) |
ASTM D 8069 : 2017 | Standard Test Method for Determining Flexural Modulus of Full Section Pultruded Fiber Reinforced Polymer (FRP) Composite Members with Doubly Symmetric Cross Sections under Bending |
ASTM F 1743 : 2017 : REDLINE | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP) |
ASTM D 3935 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 3013 : 2013 : REDLINE | Standard Specification for Epoxy Molding Compounds |
ASTM F 3219 : 2017 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
ASTM F 2026 : 2017 : REDLINE | Standard Specification for Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications |
ASTM F 988 : 1986 | Guide for Specifying Carbon-Fiber Randomly Reinforced Ultra-High-Molecular-Weight Polyethylene for Medical Devices (Withdrawn 1992) |
ASTM D 5140 : 1995 | Standard Guide for Testing Polyurethane "Poured in Place" Thermal Break Materials (Withdrawn 2004) |
ASTM D 3929 : 2003 : R2015 | Standard Test Method for Evaluating Stress Cracking of Plastics by Adhesives Using the Bent-Beam Method |
ASTM F 1697:2009 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit <a href="#fn00002"></a> |
ASTM E 2771 : 2011 : EDT 3 | Standard Terminology for Homeland Security Applications |
ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
ASTM E 2831/E2831M : 2011 | Standard Guide for Deployment of Blast Resistant Trash Receptacles in Crowded Places |
ASTM D 704 : 1999 : R2004 | Standard Specification for Melamine-Formaldehyde Molding Compounds |
ASTM D 6856/D6856M : 2003 : R2016 | Standard Guide for Testing Fabric-Reinforced “Textile” Composite Materials |
ASTM D 5813 : 2004 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
ASTM F 561 : 2013 | Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids |
ISO/TS 24817:2006 | Petroleum, petrochemical and natural gas industries Composite repairs for pipework Qualification and design, installation, testing and inspection |
I.S. EN ISO 13628-2:2006 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
CSA NGV 5.1 : 2016 | RESIDENTIAL FUELING APPLIANCES |
ANSI/NEMA LD 3:2005 | HIGH-PRESSURE DECORATIVE LAMINATES |
ANSI C37.57 : 1990 | SWITCHGEAR - METAL-ENCLOSED INTERRUPTER SWITCHGEAR ASSEMBLIES - CONFORMANCE TESTING |
ANSI C37.55 : 1989 | MEDIUM VOLTAGE METAL-CLAD ASSEMBLIES - CONFORMANCE TEST PROCEDURES |
AASHTO R 63 : 2013 | PRACTICE FOR SOLID WALL HIGH-DENSITY POLYETHYLENE (HDPE) CONDUIT FOR NON-PRESSURE APPLICATIONS USED FOR THE PROTECTION OF POWER AND TELECOMMUNICATIONS CABLES |
ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
SAE AMS 3903 : 2013 | CLOTH, ORGANIC FIBER (PARA-ARAMID), HIGH MODULUS, EPOXY RESIN IMPREGNATED |
DD CEN ISO/TS 24817:2011 | Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection |
MIL-O-71130 Base Document:1992 | OBTURATING BAND, PLASTIC SPLIT (MOLDED) |
14/30304340 DC : 0 | BS EN ISO 17348 - PETROLEUM AND NATURAL GAS OFFSHORE PLATFORMS - GUIDELINES FOR MATERIALS SELECTION FOR HIGH CONTENT CO[2] ENVIRONMENT FOR CASINGS, TUBINGS AND DOWNHOLE EQUIPMENT |
MIL-S-62502 Base Document:1987 | SPECIFICATION FOR SHEET MOLDING COMPOUND; LOW SHRINKAGE |
BS EN ISO 80369-7:2017 | Small-bore connectors for liquids and gases in healthcare applications Connectors for intravascular or hypodermic applications |
API 14A : 2015 | SPECIFICATION FOR SUBSURFACE SAFETY VALVE EQUIPMENT |
13/30285580 DC : 0 | BS EN ISO 16961 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - INTERNAL PROTECTIVE COATING AND LINING OF ABOVE GROUND STEEL STORAGE TANKS |
CSA C22.2 No. 0.17 : 2000 : R2004 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
SAE AMS3831B | Cloth, Type “E” Glass, “B” Stage Epoxy-Resin-Impregnated 7781 Style Fabric, Flame Resistant, Improved Strength |
MIL-PRF-11588 Revision H:2009 | HOSE ASSEMBLIES, RUBBER, SYNTHETIC, LIQUID PETROLEUM FUELS, DISPENSING, COLLAPSIBLE, STANDARD AND LOW TEMPERATURE |
04/301931 DC : DRAFT JAN 2004 | ISO 13628-2 - PETROLEUM AND NATURAL GAS INDUSTRIES DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
95/101288 DC : DRAFT FEB 1995 | PREN 1825-1 - INSTALLATIONS FOR SEPARATION OF GREASE - PART 1: PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
MIL-DTL-32265 Base Document:2007 | Folded Fiberglass Mat Fabrication and Packaging |
MIL-P-24364 Base Document:1969 | PLASTIC SHEET, LAMINATED, THERMOSETTING, ELECTRICAL INSULATING SHEET, GLASS MAT |
ASTM F 1697 : 2009 : R2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit |
MIL-A-47073 Base Document:1974 | ADHESIVE, PLASTIC RESIN |
SAE AMS3811C | Rods, Aramid Fiber, Polyester Resin Coated Pultrusion |
ASTM D 707 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
SAE AMS3897A | Cloth, Carbon Fiber, Resin Impregnated |
MIL-PRF-46190 Revision A:1997 | PREPEGS, WOVEN FABRIC, CARBON FIBER, RESIN IMPREGNATED |
ANSI/AWWA C710 : 2015 | COLD-WATER METERS - DISPLACEMENT TYPE, PLASTIC MAIN CASE |
ASTM F 790 : 2008 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
ASTM D 5813 : 2004 : R2008 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
ASTM E 1434 : 2000 : R2013 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015) |
ASTM F 1533 : 2001 : R2009 | Standard Specification for Deformed Polyethylene (PE) Liner (Withdrawn 2018) |
ASTM D 6100 : 2017 : REDLINE | Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM) |
MIL P 24191 : D | PLASTIC SHEET, CAST, ACRYLIC, SHIPBOARD APPLICATION (ILLUMINATION AND SIGNAL LIGHTING) |
UNE-EN 80369-5:2017 | Small-bore connectors for liquids and gases in healthcare applications - Part 5: Connectors for limb cuff inflation applications |
ASTM D 4474 : 2000 | Standard Classification System for Styrenic Thermoplastic Elastomer Injection Molding and Extrusion Materials (TES) (Withdrawn 2008) |
ASTM C 581 : 2015 : REDLINE | Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service |
SAE AMS3628E | Plastic Extrusions and Moldings, Polycarbonate General Purpose |
ISO 24817:2017 | Petroleum, petrochemical and natural gas industries — Composite repairs for pipework — Qualification and design, installation, testing and inspection |
MIL H 53095 : A | HOSE ASSEMBLIES, RUBBER, SYNTHETIC, LIQUID PETROLEUM FUELS, DISPENSING, COLLAPSIBLE, LOW TEMPERATURE |
ASTM PS 93 : 1998 | Provisional Standard Specification for Fabricated Shapes and Finished Parts Fabricated From Polyimide Resins (Withdrawn 2001) |
SAE J1345_199505 | Automotive Plastic Parts Specification |
ASTM D 5205 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
SAE AMS3834B | Cloth, Type “E” Glass, “B” Stage Polyester-Resin-Impregnated 7781 Style Fabric, Flame Resistant, Improved Strength |
ASTM D 2341 : 1981 | Specification for Rigid Urethane Foam (Withdrawn 1988) |
ASTM G 210 : 2013 | Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus |
PREN ISO 80369-1 : DRAFT 2009 | SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
ANSI/AAMI/ISO 80369-6:2016 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 6: CONNECTORS FOR NEURAXIAL APPLICATIONS |
ASTM E 2639 : 2012 | Standard Test Method for Blast Resistance of Trash Receptacles |
BS EN ISO 24817:2017 | Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection |
ANSI/AAMI/ISO 80369-7:2016 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS |
ACI 548.10 : 2010 | SPECIFICATION FOR TYPE MMS (METHYL METHACRYLATE SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS |
ACI 440.2R : 2017 | GUIDE FOR THE DESIGN AND CONSTRUCTION OF EXTERNALLY BONDED FRP SYSTEMS FOR STRENGTHENING CONCRETE STRUCTURES |
ACI SPEC-548.10 : 2010 | SPECIFICATION FOR TYPE MMS (METHYL METHACRYLATE SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS |
ASTM D 4673 : 2016 : REDLINE | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
ASTM E 2831/E2831M : 2011 : R2018 | Standard Guide for Deployment of Blast Resistant Trash Receptacles in Crowded Places |
ASTM D 5204 : 2017 : REDLINE | CLASSIFICATION SYSTEM FOR POLYAMIDE-IMIDE (PAI) MOLDING AND EXTRUSION MATERIALS |
I.S. EN ISO 24817:2017 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION (ISO 24817:2017, CORRECTED VERSION 2018-01-01) |
ASTM D 4203 : 2017 : REDLINE | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
ASTM D 3841 : 2016 : REDLINE | Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels |
ASTM D 6339 : 2011 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
ASTM F 755:1999 | Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants |
ASTM F 1735 : 2009 : R2015 | Standard Specification for Poly (Vinyl Chloride) (PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits |
ASTM D 3517 : 2014 : REDLINE | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe |
ASTM D 7264/D7264M : 2015 : REDLINE | Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials |
ASTM D 6261 : 2014 : REDLINE | Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES) |
ASTM F 1606 : 2005 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner |
ASTM D 4349 : 2016 : REDLINE | Classification System and Basis for Specification for Polyphenylene Ether (PPE) Materials |
EN ISO 80369-1:2010 | Small bore connectors for liquids and gases in healthcare applications - Part 1: General requirements (ISO 80369-1:2010) |
BS EN ISO 12086-2:2006 | Plastics. Fluoropolymer dispersions and moulding and extrusion materials Preparation of test specimens and determination of properties |
ASTM D 3485 : 2015 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
CSA S806: 2012 | DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS |
CSA C22.2 No. 126.2:2002 | NONMETALLIC CABLE TRAY SYSTEMS |
ASTM C 1349 : 2017 : REDLINE | Standard Specification for Architectural Flat Glass Clad Polycarbonate |
CSA C22.2 No. 126.2 : 2002 : INC : UPD 1 : 2005 : R2012 | NONMETALLIC CABLE TRAY SYSTEMS |
UNI EN ISO 13628-2 : 2007 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
UNI EN ISO 12086-2 : 2006 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
ASTM F 1635 : 2016 : REDLINE | Standard Test Method for <emph type="bdit">in vitro</emph> Degradation Testing of Hydrolytically Degradable Polymer Resins and Fabricated Forms for Surgical Implants |
ASTM D 3753 : 2012-04 | SPECIFICATION FOR GLASS-FIBER-REINFORCED POLYESTER MANHOLES AND WETWELLS |
SAE AMS3821C | Cloth, Type \"E\" Glass, \"B\" Stage Epoxy-Resin-Impregnated 7781 Style Fabric, Flame Resistant |
ASTM F 2561 : 2017 : REDLINE | Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner |
API SPEC 19OH : 2018 | OPENHOLE ISOLATION EQUIPMENT |
14/30277509 DC : 0 | BS ISO 18250-3 - CONNECTORS FOR RESERVOIR DELIVERY SYSTEMS - PART 2: ENTERNAL APPLICATIONS |
10/30191247 DC : DRAFT APR 2010 | BS EN ISO 13628-16 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 16: SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT |
ASTM F 1876 : 1998 | Standard Specification for Polyetherketoneetherketoneketone (PEKEKK) Resins for Surgical Implant Applications |
SAE AMS 3913 : 2014 | RADOME, FOAM SANDWICH, HOT-MELT, ADDITION-TYPE POLYIMIDE |
CEI UNI EN/ISO 80369-7 : 1ED 2017 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS |
BS EN ISO 16961:2015 | Petroleum, petrochemical and natural gas industries. Internal coating and lining of steel storage tanks |
SAE AMS3670/3B | Polyamide-Imide Bar, Rod, and Shapes 12% Graphite - 3% Polytetrafluoroethylene Filled |
MIL-C-46866 Base Document:1973 | COMPOUND, EPOXY MOLDING AND APPLICATION OF |
MIL-C-24449 Revision A:1981 | CAST POLYMETHYL METHACRYLATE FOR SHEET STOCK, CUSTOM CASTINGS AND FINISHED WINDOWS |
ASTM D 4098 : 1982 : R1987 : EDT 1 | Practice for Evaluating High-Density Rigid Cellular Thermosets (Withdrawn 1994) |
ASTM D 1636 : 2013 : REDLINE | Standard Specification for Allyl Molding Compounds |
ANSI/AAMI/ISO 80369-5:2016 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 5: CONNECTORS FOR LIMB CUFF INFLATION APPLICATIONS |
ASTM F 624 : 2009 | Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications |
BS EN ISO 80369-3:2016 | Small-bore connectors for liquids and gases in healthcare applications Connectors for enteral applications |
UNE-EN ISO 80369-3:2017 | Small-bore connectors for liquids and gases in healthcare applications - Part 3: Connectors for enteral applications (ISO 80369-3:2016) |
DOD-STD-35-24 Revision A:1978 | AUTOMATED ENGINEERING DOCUMENT PREPARATION SYSTEM, BEARINGS |
MIL-PRF-370 Revision K:2017 | HOSE AND HOSE ASSEMBLIES, NONMETALLIC: ELASTOMERIC, LIQUID FUEL |
MIL-PRF-62419 Revision B:2010 | COMPOSITE MATERIALS FOR MILITARY VEHICLES |
CTI STD 124 : 2013 | FRP FAN STACK MATERIAL |
14/30256269 DC : 0 | BS EN ISO 24817 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
13/30242622 DC : 0 | BS ISO 12891-2 - RETRIEVAL AND ANALYSIS OF SURGICAL IMPLANTS - PART 2: ANALYSIS OF RETRIEVED SURGICAL IMPLANTS |
ADS-13F-HDBK : 1997 | AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES |
ASTM F 639 : 2009 : R2015 | Standard Specification for Polyethylene Plastics for Medical Applications |
DD ISO/TS 24817 : 2006 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
ASTM PS 2 : 1994 | Specification for Molding Plastics, Electrical, Thermoplastic (Withdrawn 1997) |
ASTM F 2376 : 2017 : REV A : REDLINE | Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems |
MIL-DTL-20268 Revision H:2017 | FRAME, CAP |
MIL-PRF-46187 Revision A:1998 | PREPREG, UNIDIRECTIONAL TAPE, CARBON (GRAPHITE) FIBER HIGH TEMPERATURE RESIN IMPREGNATED, 316 DEGREES C (600 DEGREES F) |
ASTM F 2820 : 2012 | Standard Specification for Polyetherketoneketone (PEKK) Polymers for Surgical Implant Applications |
ASTM F 1541 : 2017 : REDLINE | Standard Specification and Test Methods for External Skeletal Fixation Devices |
ASTM F 2019 : 2011 : REDLINE | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP) |
ASTM F 1735:2009 | Standard Specification for Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits |
17/30325386 DC : 0 | BS ISO 18250-1- CONNECTORS FOR RESERVOIR DELIVERY SYSTEMS - PART 1: GENERAL REQUIREMENTS AND COMMON TEST METHODS |
API 17J REDLINE : 2008 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
SAE AMS3849C | Cloth, Quartz, Style 581 Fabric Hot-Melt, Addition-Type, Polyimide Resin Impregnated |
I.S. EN 80369-5:2016 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 5: CONNECTORS FOR LIMB CUFF INFLATION APPLICATIONS |
ISO 12891-2:2014 | Retrieval and analysis of surgical implants Part 2: Analysis of retrieved surgical implants |
ASTM D 4357 : 1996 | Standard Specification for Plastic Laminates Made from Woven-Roving and Woven-Yarn Glass Fabrics (Withdrawn 2004) |
ASTM F 1533 : 2001 | Standard Specification for Deformed Polyethylene (PE) Liner |
ASTM D 6272 : 2017 : REDLINE | Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending |
SAE AMS3827C | Cloth, Type \"E” Glass, “B” Stage Polyester-Resin-Impregnated 7781 Style Fabric, Flame Resistant |
ASTM D 4634 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
ASTM D 5593 : 1999 : EDT 1 | Standard Classification for Thermoplastic Elastomers-Olefinic (TEO) (Withdrawn 2005) |
ASTM D 6263 : 2015 : REDLINE | Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) |
ASTM F 1867 : 2006 : R2012 | Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation |
ASTM F 648 : 2014 : REDLINE | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Powder and Fabricated Form for Surgical Implants |
ASTM C 582 : 2009 : R2016 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
ASTM F 1579 : 2002 : EDT 1 | Standard Specification for Polyaryletherketone (PAEK) Polymers for Surgical Implant Applications (Withdrawn 2011) |
ASTM F 2695 : 2012 : REDLINE | Standard Specification for Ultra-High Molecular Weight Polyethylene Powder Blended With Alpha-Tocopherol (Vitamin E) and Fabricated Forms for Surgical Implant Applications |
ASTM F 1504 : 2014 : REDLINE | Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation |
DIN EN ISO 80369-1:2015-09 (Draft) | SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
ASTM D 7032 : 2017 : REDLINE | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
ASTM E 1434 : 2000 : R2006 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
ASTM F 1871 : 2011-06 | SPECIFICATION FOR FOLDED/FORMED POLY (VINYL CHLORIDE) PIPE TYPE A FOR EXISTING SEWER AND CONDUIT REHABILITATION |
GOST 849:2018 | Primary nickel. SpecificationsE |
ISO 16961:2015 | Petroleum, petrochemical and natural gas industries — Internal coating and lining of steel storage tanks |
ISO 80369-7:2016 | Small-bore connectors for liquids and gases in healthcare applications Part 7: Connectors for intravascular or hypodermic applications |
ISO 12086-2:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
ISO 13628-2:2006 | Petroleum and natural gas industries Design and operation of subsea production systems Part 2: Unbonded flexible pipe systems for subsea and marine applications |
ISO 17348:2016 | Petroleum and natural gas industries — Materials selection for high content CO2 for casing, tubing and downhole equipment |
DIN EN 80369-5:2017-10 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 5: CONNECTORS FOR LIMB CUFF INFLATION APPLICATIONS (IEC 80369-5:2016 + COR.1:2017) |
EN ISO 17348:2016 | Petroleum and natural gas industries - Materials selection for high content CO2 environment for casings, tubings and downhole equipment (ISO 17348:2016) |
EN ISO 80369-3:2016 | Small-bore connectors for liquids and gases in healthcare applications - Part 3: Connectors for enteral applications (ISO 80369-3:2016) |
EN ISO 16961:2015 | Petroleum, petrochemical and natural gas industries - Internal coating and lining of steel storage tanks (ISO 16961:2015) |
ASTM F 636 : 1985 : R1991 | Guide for Selection of Tests for Material Properties of Transfer Molding Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996) |
MIL-DTL-17901 Revision C:2005 | Bearing Components, Bonded Synthetic Rubber, Water Lubricated |
MIL C 47027 : 0 | COMPOUND, MOLDING, PLASTIC, RIGID, THERMOPLASTIC |
SAE AMS3732B | Potting Compound, Epoxy One Part, Filled, Heat Cure, Low CTE |
MIL-B-21408 Revision G:1984 | BOOTS, SAFETY |
MIL-R-46198 Base Document:1988 | RESIN, POLYIMIDE, HOT PRESSED OR PRESSED AND SINTERED |
SAE AMS 3912 : 2014 | RADOMES, FOAM SANDWICH, POLYIMIDE/QUARTZ CLOTH CONSTRUCTION |
MIL-M-24325 Base Document:1968 | MOLDING MATERIAL PLASTIC, EPOXY COMPOUNDS THERMOSETTING |
ASTM F 1867 : 2006 | Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation |
MIL-B-82789 Base Document:1990 | BROADGOODS, SILICA CLOTH, PHENOLIC IMPREGNATED |
MMM-A-1754 Base Document:1973 | ADHESIVE AND SEALING COMPOUND EPOXY METAL FILLED |
MIL L 46197 : (1) | LAMINATE: HIGH STRENGTH GLASS, FABRIC REINFORCED, POLYESTER RESIN PREIMPREGNATED |
MIL-P-17549 Revision D:1981 | PLASTIC LAMINATES, FIBROUS GLASS REINFORCED, MARINE STRUCTURAL |
ASTM D 3641 : 2015 : REDLINE | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
MIL-B-82792 Base Document:1990 | BROADGOODS, CARBON CLOTH, PHENOLIC IMPREGNATED |
I.S. EN ISO 80369-1:2010 | SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 1: GENERAL REQUIREMENTS |
13/30285694 DC : 0 | BS EN ISO 80369-3 - SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 3: CONNECTORS FOR ENTERAL APPLICATIONS |
SAE AMS3731C | Potting Compound, Epoxy Bisphenol A-Type |
UNE-EN ISO 80369-7:2017 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
ASTM D 4097 : 2001 : R2010 | Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks |
SAE J1875_200105 | Materials for Plastic Check Valves for Vacuum Booster Systems |
13/30255554 DC : 0 | BS EN ISO 80369-7 - SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS WITH 6% (LUER) TAPER FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS |
MIL-R-24719 Base Document:1989 | RESINS, VINYL ESTER, LOW PRESSURE LAMINATING |
MIL O 70548 : 0 | OBURATING BAND, PLASTIC SPLIT (MOLDED) |
BS EN ISO 80369-1:2010 | Small bore connectors for liquids and gases in healthcare applications General requirements |
ABS 0063 : 2018 COR 2018 | RULES FOR BUILDING AND CLASSING FACILITIES ON OFFSHORE INSTALLATIONS |
EN ISO 80369-7:2017 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
ASTM D 5138 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
14/30288421 DC : 0 | BS EN ISO/IEC 80369-6 - SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 6: CONNECTORS FOR NEURAXIAL APPLICATIONS |
SAE AMS3829C | Cloth, Type “E”-Glass, Style 7781 Fabric Solution-Addition-Type PMR-15 Polyimide Resin Impregnated |
MIL-B-82800 Base Document:1983 | BROADGOODS, GRAPHITE CLOTH, PHENOLIC IMPREGNATED |
MIL T 82840 : NOTICE 1 | TAPE, SILICAL CLOTH, PHENOLIC - PREIMPREGNATED |
MIL-F-10336 Revision E:1977 | FIBER SHEET, VULCANIZED |
ASTM F 1876 : 1998 : R2003 : EDT 1 | Standard Specification for Polyetherketoneetherketoneketone (PEKEKK) Resins for Surgical Implant Applications (Withdrawn 2012) |
API SPEC 17J : 2014 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
MIL-R-47025 Revision A:1991 | RESIN, CASTING, FIRE RETARDANT, EPOXY BASE |
MIL-DTL-83420 Revision P:2017 | WIRE ROPE, FLEXIBLE, FOR AIRCRAFT CONTROL, GENERAL SPECIFICATION FOR |
MIL T 82839 : NOTICE 1 | TAPE, CARBON CLOTH, PHENOLIC PREIMPREGNATED |
MIL-V-29591 Base Document:1992 | VISOR ASSEMBLY, AVIATOR'S SEVEN WAVELENGTH LASER PROTECTIVE, GENERAL SPECIFICATION FOR |
B184 SERIES-17 | Polymeric subsurface stormwater management structures |
04/30091870 DC : DRAFT FEB 2004 | BS EN ISO 12086-2 - PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
MIL-P-46184 Base Document:1982 | PLASTIC MOLDING & EXTRUSION MATERIAL, POLYETHERIMIDE (PEI) |
ASTM D 2304 : 2010-10 | TEST METHOD FOR THERMAL ENDURANCE OF RIGID ELECTRICAL INSULATING MATERIALS |
A-A-59528 Base Document:1999 | SHOE, MOLDERS |
CSA A440 : 2017 | NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS |
CEI UNI EN ISO 80369-3 : 2017 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 3: CONNECTORS FOR ENTERAL APPLICATIONS |
ASTM D 5943 : 1996 | Test Method for Determination of Flexural Properties (Withdrawn 1998) |
IEEE 1310-2012 REDLINE | IEEE Recommended Practice for Thermal Cycle Testing of Form-Wound Stator Bars and Coils for Large Rotating Machines |
ACI PRC-548.3 : 2009 | REPORT ON POLYMER-MODIFIED CONCRETE |
A500-16 | Building guards |
ASTM D 7293 : 2012 : REDLINE | Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI) |
I.S. EN ISO 16961:2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - INTERNAL COATING AND LINING OF STEEL STORAGE TANKS (ISO 16961:2015) |
ASTM D 7082 : 2015 : REDLINE | Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe |
SAE AMS3617F : 2014 | POLYAMIDE TYPE 6-6, PLASTIC MOLDINGS AND EXTRUSIONS |
API TR 17TR8 : 2018 | HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES |
SAE AMS3812C | Rods, Glass Fiber, Polyester Resin, Loaded Pultrusion |
EN ISO 80369-6 : 2016 COR 2016 | SMALL BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 6: CONNECTORS FOR NEURAXIAL APPLICATIONS (ISO 80369-6:2016, CORRECTED VERSION 2016-11-15) |
ASTM F 2881/F2881M : 2018 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
ASTM D 3929 : 2003 : R2010 : EDT 1 | Standard Test Method for Evaluating Stress Cracking of Plastics by Adhesives Using the Bent-Beam Method |
ASTM F 2718 : 2009 | Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines |
ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
ASTM F 1092 : 2014 : REDLINE | Standard Specification for Fiberglass (GRP) Pultruded Open-Weather Storm and Guard, Square Railing Systems |
ASTM D 6856 : 2003 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM E 2478 : 2011 : R2016 | Standard Practice for Determining Damage-Based Design Stress for Glass Fiber Reinforced Plastic (GFRP) Materials Using Acoustic Emission |
ASTM F 2718 : 2009 : R2015 | Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022) |
ASTM E 1420 : 1991 | Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996) |
ASTM F 2160 : 2016 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
ASTM F 755 : 1999 : R2011 | Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants |
ASTM D 5990 : 2000 | Standard Classification System for Polyketone Injection Molding and Extrusion Materials (PK) (Withdrawn 2007) |
ASTM D 6394 : 2014 : REDLINE | Standard Specification for Sulfone Plastics (SP) |
ASTM F 1251 : 1989 : R2003 | Standard Terminology Relating to Polymeric Biomaterials in Medical and Surgical Devices (Withdrawn 2012) |
ASTM D 5813 : 2004 : R2012 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
ASTM E 2771 : 2011 : EDT 2 | Standard Terminology for Homeland Security Applications |
SAE AMS3844C | Cloth, Type \"E\" Glass, Style 7781 Fabric Hot-Melt, Addition-Type, Polyimide Resin Impregnated |
ASTM F 641 : 2009 : R2014 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
ASTM F 1579 : 2002 | Standard Specification for Polyaryletherketone (PAEK) Polymers for Surgical Implant Applications |
ASTM E 1309 : 2000 : R2011 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases (Withdrawn 2015) |
ASTM D 3222 : 2005 : R2010 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM E 2740 : 2012 : EDT 1 | Standard Specification for Trash Receptacles Subjected to Blast Resistance Testing |
ASTM D 5948 : 2005 : EDT 1 | Standard Specification for Molding Compounds, Thermosetting |
ASTM F 3131 : 2014 | Standard Specification for Epoxy / Cotton Raw Materials for the Use in Bearing Cages |
ASTM D 7745 : 2011 | Standard Practice for Testing Pultruded Composites |
ASTM E 1309 : 2000 : R2005 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM F 639 : 2009 | Standard Specification for Polyethylene Plastics for Medical Applications |
ASTM D 7774 : 2017 : REDLINE | Standard Test Method for Flexural Fatigue Properties of Plastics |
ASTM E 2478 : 2011 | Standard Practice for Determining Damage-Based Design Stress for Glass Fiber Reinforced Plastic (GFRP) Materials Using Acoustic Emission |
S.R. CEN ISO TS 24817:2011 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION |
DIN EN ISO 80369-7:2017-10 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
DIN EN ISO 12086-2:2006-05 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
CEN ISO/TS 24817:2011 | Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO/TS 24817:2006) |
ASME PVHO 2 : 2016 | SAFETY STANDARD FOR PRESSURE VESSELS FOR HUMAN OCCUPANCY: IN-SERVICE GUIDELINES |
ASME RTP 1 : 2015 | REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT |
ASME RTP-1 : 2017 | REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT |
PIP VESFG001 : 2011 | FIBERGLASS TANK AND VESSEL SPECIFICATION |
CSA/ANSI NGV 5.2-2017 | Vehicle fueling appliances (VFA) |
ASME PVHO 1 : 2016 | SAFETY STANDARD FOR PRESSURE VESSELS FOR HUMAN OCCUPANCY |
ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
ASTM D 6272 : 2017 : REDLINE | Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending |
ASTM E 2309 : 2005 | Standard Practices for Verification of Displacement Measuring Systems and Devices Used in Material Testing Machines |
ISO 178:2010 | Plastics Determination of flexural properties |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.