ATS 5200.478-2006

1 - ATS 5200.478-2006 TECHNICAL SPECIFICATION FOR PLUMBING AND DRAINAGE PRODUCTS - CROSS-LINKED POLYETHYLENE/ALUMINIUM/CROSS...
4 - PREFACE
5 - CONTENTS
6 - 1 SCOPE
6 - 2 APPLICATION
6 - 3 REFERENCED DOCUMENTS
7 - 4 DEFINITIONS
7 - 5 MATERIALS
7 - 5.1 Pipes
7 - 5.1.1 Carbon black
7 - 5.1.2 Dispersion of additives
7 - 5.2 Fittings
7 - 5.2.1 Copper alloy
7 - 5.2.2 Dezincification-resistant (DR) copper alloy
7 - 5.2.3 Stainless steel
8 - 5.2.4 Plastics materials utilized as components
8 - 6 MARKING
8 - 6.1 Pipes
8 - 6.2 Fittings
8 - 7 PACKAGING
9 - 8 DESIGN
9 - 8.1 Pipes
9 - 8.1.1 Classification
9 - 8.1.2 Dimensions
9 - 8.1.3 Length
9 - 8.1.4 Freedom from defects
9 - 8.1.5 Colour
9 - 8.2 Fittings
9 - 8.2.1 Adaptor end connections
10 - 8.2.2 Freedom from defects
10 - 9 PERFORMANCE REQUIREMENTS AND TEST METHODS
10 - 9.1 Products in contact with drinking water
10 - 9.2 Performance requirements pipes
10 - 9.2.1 Adhesion
10 - 9.2.2 Burst Test
10 - 9.2.3 Pressure resistance
11 - 9.2.4 Long-term rupture
11 - 9.2.5 Degree of cross-linking
11 - 9.2.6 Environmental stress crack resistance
11 - 9.3 Performance requirements and test methods for fittings
11 - 9.3.1 Compatibility of fittings with pipe
11 - 9.3.2 Resistance to leakage when subject to bending
11 - 9.3.3 Resistance to pull-out of assembled joints
12 - 9.3.4 Thermal cycling test
12 - 9.3.5 Liquid infiltration
12 - 9.3.6 Pressure cycling test (not applicable to gas applications)
12 - 10 'VOID'
12 - 11 PRODUCT DOCUMENTATION
12 - 11.1 Product data
12 - 11.2 Installation instructions
13 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS TECHNICAL SPECIFICATION
13 - A1 SCOPE
13 - A2 RELEVANCE
13 - A3 PRODUCT CERTIFICATION
13 - A4 DEFINITIONS
13 - A4.1 Batch release test
13 - A4.2 Production batch
13 - A4.3 Sample
13 - A4.4 Sampling plan
13 - A4.5 Type test batch
13 - A4.6 Type testing (TT)
14 - A5 TESTING
14 - A5.1 Type testing
14 - A5.2 Batch release testing
14 - A5.3 Retesting

This Australian Technical Specification specifies requirements for macro-composite pipes and associated fittings generally for the conveyance of water in sizes ranging from DN 16 to DN 63.

This Australian Technical Specification specifies requirements for macro-composite pipes and associated fittings generally for the conveyance of water in sizes ranging from DN16 to DN63.Cross-linked polyethylene/Aluminium/Cross-linked polyethylene macro-composite pipes may be used at continuous operating temperatures up to 80C with short exposures up to 100C and operating pressures not exceeding 1.4MPa.The macro-composite pipes covered in this Technical Specification consist of an aluminium core encapsulated in, and bonded to, an inner and outer layer of cross-linked polyethylene.Polyethylene or cross-linked polyethylene macro-composite pipes that are either natural or of colours other than black are not suitable for use or extended storage where exposed to direct sunlight.

First published as ATS 5200.478-2006.