BS EN 15345:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics. Recycled plastics. Characterization of polypropylene (PP) recyclates
Hardcopy , PDF
English
02-29-2008
06-05-2025
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 Characteristics of PP recyclates
5 Quality Assurance
Annex A (Normative) - Test Method for the determination
of bulk density
Bibliography
Describes a method of specifying delivery conditions for Polypropylene (PP) recyclates.
| Committee |
PRI/89
|
| DevelopmentNote |
Supersedes 05/30097529 DC. (02/2008)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This European Standard defines a method of specifying delivery conditions for Polypropylene (PP) recyclates. It gives the most important characteristics and associated test methods for assessing a single batch of PP recyclates intended for use in the production of semi-finished/finished products. It is intended to support parties involved in the use of recycled PP to agree on specifications for specific and general applications. This standard does not cover the characterisation of plastics wastes. See EN 15347. This standard is applicable without prejudice to any existing legislation.
| Standards | Relationship |
| I.S. EN 15345:2007 | Identical |
| NEN EN 15345 : 2007 | Identical |
| NS EN 15345 : 1ED 2007 | Identical |
| UNE-EN 15345:2008 | Identical |
| EN 15345:2007 | Identical |
| NF EN 15345 : 2008 | Identical |
| DIN EN 15345:2008-02 | Identical |
| NBN EN 15345 : 2008 | Identical |
| EN ISO 1043-3:1999 | Plastics - Symbols and abbreviated terms - Part 3: Plasticizers (ISO 1043-3:1996) |
| ISO 3451-1:2008 | Plastics — Determination of ash — Part 1: General methods |
| CEN/TR 15353:2007 | Plastics - Recycled plastics - Guidelines for the development of standards for recycled plastics |
| EN 15343:2007 | Plastics - Recycled Plastics - Plastics recycling traceability and assessment of conformity and recycled content |
| EN ISO 1043-2:2011 | Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials (ISO 1043-2:2011) |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| ISO 1873-1:1995 | Plastics — Polypropylene (PP) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| EN ISO 3451-1:2008 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008) |
| ISO 11469:2016 | Plastics — Generic identification and marking of plastics products |
| EN ISO 11469:2016 | Plastics - Generic identification and marking of plastics products (ISO 11469:2016) |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 1043-3:2016 | Plastics — Symbols and abbreviated terms — Part 3: Plasticizers |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN ISO 1873-1:1995 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1873-1:1995) |
| ISO 1043-2:2011 | Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 1043-4:1998 | Plastics — Symbols and abbreviated terms — Part 4: Flame retardants |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| ASTM D 5577 : 1994 | Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.