I.S. EN 15342:2007
Current
Current
The latest, up-to-date edition.
PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLYSTYRENE (PS) RECYCLATES
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2007
Publisher
US$44.40
Excluding Tax where applicable
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 Characterisation of PS recyclates
5 Quality assurance
Annex A (normative) - Test Method for the determination of
bulk density
Bibliography
Describes a method of specifying delivery condition characteristics for polystyrene (PS) recyclates.
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| NF EN 15342 : 2008 | Identical |
| NEN EN 15342 : 2007 | Identical |
| EN 15342:2007 | Identical |
| NBN EN 15342 : 2008 | Identical |
| DIN EN 15342:2008-02 | Identical |
| NS EN 15342 : 1ED 2007 | Identical |
| UNE-EN 15342:2008 | Identical |
| BS EN 15342:2007 | Identical |
| BS EN 15342:2007 | Equivalent |
| ISO 1622-1:2012 | Plastics — Polystyrene (PS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| EN ISO 2897-1:1999 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2897-1:1997) |
| EN ISO 1043-3:1999 | Plastics - Symbols and abbreviated terms - Part 3: Plasticizers (ISO 1043-3:1996) |
| ISO 3451-1:2008 | Plastics — Determination of ash — Part 1: General methods |
| CEN/TR 15353:2007 | Plastics - Recycled plastics - Guidelines for the development of standards for recycled plastics |
| EN 15343:2007 | Plastics - Recycled Plastics - Plastics recycling traceability and assessment of conformity and recycled content |
| EN ISO 1043-2:2011 | Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials (ISO 1043-2:2011) |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN ISO 3451-1:2008 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008) |
| ISO 11469:2016 | Plastics — Generic identification and marking of plastics products |
| EN ISO 11469:2016 | Plastics - Generic identification and marking of plastics products (ISO 11469:2016) |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| ISO 2897-1:1997 | Plastics — Impact-resistant polystyrene (PS-I) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ASTM D 5676 : 1999 | Standard Specification for Recycled Polystyrene Molding and Extrusion Materials (Withdrawn 2004) |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 1043-3:2016 | Plastics — Symbols and abbreviated terms — Part 3: Plasticizers |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| EN ISO 1622-1:2012 | Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1622-1:2012) |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 1043-2:2011 | Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| EN ISO 306:2013 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| ISO 1043-4:1998 | Plastics — Symbols and abbreviated terms — Part 4: Flame retardants |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| ASTM D 5577 : 1994 | Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.