AS 4032.2-2005
Current
The latest, up-to-date edition.
Water supply - Valves for the control of hot water supply temperatures Tempering valves and end-of-line temperature-actuated devices (Reconfirmed 2015)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
12-13-2005
The objective of this Standard is to provide manufacturers with requirements for tempering valves and end-of-line temperature-actuated devices that give reasonable protection to users against exposure to high or excessive fluctuations in mixed water temperatures caused by the following: - Maintaining an outlet temperature within specified limits, including shut-off of the cold water supply. - Closing the outlet when the mixed water temperature exceeds a specified maximum.
This Standard specifies requirements for the design, construction, testing and performance of - (a) tempering valves of nominal sizes not larger than DN32; and(b) end-of-line temperature-actuated devices of nominal size not larger than DN25,for use with heated water at - (i) continuous operating temperature not exceeding 85°C;(ii) temperature under emergency conditions, not exceeding 99°C; and(iii) continuous working pressure not exceeding 1400kPa.Devices complying with this Standard are intended to prevent a continuous discharge of water from the outlet in excess of 50°C under steady-state conditions.Transient discharges of water with a temperature in excess of this figure, which comply with the specified cumulative time/temperature factors, are acceptable.NOTE: Tempering valves, when adjusted to an outlet temperature not exceeding 50°C, and end-of-line devices may be used for temperature-limiting for ablution purposes, to minimize the risk of scalding, other than for use in health care, aged care, child care, care for people with disabilities and any other at-risk situations. Thermostatic mixing valves complying with AS4032.1, when adjusted to an outlet temperature not exceeding 45°C, are intended for use in health care, aged care, child care, care for people with disabilities and any other at-risk situations.
Committee |
WS-026
|
DocumentType |
Standard
|
ISBN |
0 7337 7048 7
|
Pages |
40
|
ProductNote |
Reconfirmed 14/07/2015.This standard as been reconfirmed in Australia in 2015 and remains current in New Zealand. Reconfirmation Notice 14/07/2015
|
PublisherName |
Standards Australia
|
Status |
Current
|
Supersedes | |
UnderRevision |
First published as AS4032.2-2002.Second Edition 2005. Originated as AS 4032.2-2002. Second Edition 2005. Reissued incorporating Amendment No. 1 (October 2006). Reissued incorporating Amendment No. 2 (June 2009).
ATS 5200.006-2005 | Technical Specification for plumbing and drainage products Reflux valves - Sewerage |
ATS 5200.033-2004 | Technical Specification for plumbing and drainage products Spraying apparatus/dispensing units with the option of chemical additions - Hose connected |
ATS 5200.006-2004 | Technical Specification for plumbing and drainage products Reflux valves - sewerage |
ATS 5200.021-2004 | Technical Specification for plumbing and drainage products Flushing valves for water closets and urinals - for use with break tank supply |
AS/NZS 4020:2005 | Testing of products for use in contact with drinking water |
AS 1722.1-1975 | Pipe threads of Whitworth form Sealing pipe threads (metric units) |
AS/NZS 3500.0:2003 | Plumbing and drainage Glossary of terms |
ATS 5200.467-2004 | Technical Specification for plumbing and drainage products Rainwater tank connection valve |
ATS 5200.463-2005 | Positive air pressure attenuator |
ATS 5200.464-2004 | Technical Specification for plumbing and drainage products - Hot water manual or sensor-activated pumping systems |
ATS 5200.468-2005 | Technical Specification for plumbing and drainage products Hot water systems - Recirculation valves |
ATS 5200.014-2004 | Technical Specification for plumbing and drainage products - Jointing materials |
ATS 5200.999-2005 | Technical Specification for plumbing and drainage products Developing technical specifications |
ATS 5200.471-2005 | Technical specification for plumbing and drainage products Stainless steel tubes and mechanical compression fittings for pressure applications - Alternative systems |
AS/NZS 3499:1997 | Flexible tube connectors for water supply |
ATS 5200.028-2004 | Technical Specification for plumbing and drainage products - Commercial food waste disposal unit |
AS/NZS 1567:1997 | Copper and copper alloys - Wrought rods, bars and sections (Reconfirmed 2021) |
ATS 5200.104-2005 | Appliances (miscellaneous) |
ATS 5200.105-2005 | |
ATS 5200.030-2004 | Technical Specification for plumbing and drainage products - Solenoid valves |
ATS 5200.040-2005 | Waste pipe connection outlets and gratings, separate or integral |
ATS 5200.007-2004 | Technical Specification for plumbing and drainage products - Water hammer arrestors |
AS 2136-1977 | Method for detecting the susceptibility of copper and its alloys to stress corrosion cracking using the mercurous nitrate test (Reconfirmed 2018) |
AS 1349-1986 | Bourdon tube pressure and vacuum gauges (Reconfirmed 2018) |
AS 2738-2000 | Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings (Reconfirmed 2018) |
ATS 5200.026-2004 | Technical Specification for plumbing and drainage products Cold water storage tanks |
ATS 5200.420-2005 | Technical Specification for plumbing and drainage products Trap-priming valves |
ATS 5200.017-2005 | Technical Specification for plumbing and drainage products Cistern outlet valves |
AS/NZS 1568:1998 | Copper and copper alloys - Forging stock and forgings |
AS 2837-1986 | Wrought alloy steels - Stainless steel bars and semi-finished products |
ATS 5200.103-2004 | Technical Specification for plumbing and drainage products - Water treatment systems (other than those specified in AS/NZS 3497) |
ATS 5200.101-2005 | Appliances (low hazard rating) |
ATS 5200.016-2005 | Technical Specification for plumbing and drainage products - Cistern inlet valves |
ATS 5200.004-2005 | Technical Specification for plumbing and drainage products Urinal flushing cisterns |
ATS 5200.050-2005 | Technical Specification for plumbing and drainage products Prefabricated bathroom modules |
AS 1834.1-1991 | Material for soldering Solder alloys (Reconfirmed 2018) |
AS/NZS 1167.1:2005 | Welding and brazing - Filler metals Filler metal for brazing and braze welding |
AS 1572-1998 | Copper and copper alloys - Seamless tubes for engineering purposes (Reconfirmed 2018) |
ATS 5200.046-2005 | Technical Specification for plumbing and drainage products Diversion systems - Wash down and first flush |
ATS 5200.042-2004 | Technical Specification for plumbing and drainage products - Roll-grooved jointing systems |
AS 4032.3-2004 | Water supply - Valves for the control of heated water supply temperatures Requirements for field-testing, maintenance or replacement of thermostatic mixing valves, tempering valves and end-of-line temperature control devices |
ATS 5200.052-2005 | Metallic-bodied inlet pressure control valves greater than DN 50 |
ATS 5200.051-2005 | Technical Specification for plumbing and drainage products Bidet douche seats |
AS 3558.5-1999 | Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of degradation by ultraviolet light (Reconfirmed 2016) |
AS 5200.000-2005 | Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products |
ATS 5200.466-2004 | Technical Specification for plumbing and drainage products - Rainwater tank connection devices |
ATS 5200.460-2005 | Technical Specification for plumbing and drainage products Grey water diversion device (GWDD) |
AS 3688-2005 | Water supply - Metallic fittings and end connectors |
ATS 5200.469-2005 | Technical Specification for plumbing and drainage products Waterless or limited flush urinals - With an integral sealing device |
AS 1722.2-1992 | Pipe threads of Whitworth form Fastening pipe threads (Reconfirmed 2017) |
ATS 5200.453-2004 | Technical Specification for plumbing and drainage products Heated water systems - Thermostatic circulation valve |
ATS 5200.047-2005 | Technical Specification for plumbing and drainage products Self-sealing devices |
ATS 5200.461-2004 | Technical Specification for plumbing and drainage products Stainless steel tubes and mechanical compression fittings for pressure applications |
ATS 5200.012-2005 | Technical Specification for plumbing and drainage products In-line valves for use in plumbing water supply systems - Miscellaneous types metallic and non-metallic |
AS 1432-2004 | Copper tubes for plumbing, gasfitting and drainage applications |
ATS 5200.458-2004 | Technical Specification for plumbing and drainage products Universal transition fitting |
ATS 5200.037.2-2005 | Technical Specification for plumbing and drainage products Flow controllers - For use in heated or cold water plumbing systems |
AS 1565-1996 | Copper and copper alloys - Ingots and castings (Reconfirmed 2020) |
AS 2345-1992 | Dezincification resistance of copper alloys |
ATS 5200.459-2004 | |
ATS 5200.037-2004 | Technical Specification for plumbing and drainage products - Flow controllers |
ATS 5200.020-2004 | Technical Specification for plumbing and drainage products Flushing valves for water closets and urinals - for use with mains supply |
AS 4032.1-2005 | Water supply - Valves for the control of heated water supply temperatures Thermostatic mixing valves - Materials design and performance requirements |
AS 5200.000-2006 | Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products (Reconfirmed 2018) |
AS/NZS 3500.5:2012 | Plumbing and drainage Housing installations |
AS/NZS 3500.4:2003 | Plumbing and drainage Heated water services |
MP 52-2005 | Manual of authorization procedures for plumbing and drainage products |
AS/NZS 3500.4:2018 | Plumbing and drainage Heated water services |
AS 3498:2020 | Safety and public health requirements for plumbing products - Water heaters and hot-water storage tanks |
AS 3498-2003 | Authorization requirements for plumbing products - Water heaters and hot-water storage tanks |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.