I.S. EN 206-1:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY (INCLUDING IRISH NATIONAL ANNEX)
Hardcopy , PDF
25-06-2014
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Symbols and abbreviations
4 Classification
4.1 Exposure classes related to environmental actions
4.2 Fresh concrete
4.2.1 Consistence classes
4.2.2 Classes related to maximum aggregate size
4.3 Hardened concrete
4.3.1 Compressive strength classes
4.3.2 Density classes for light-weight concrete
5 Requirements for concrete and methods of verification
5.1 Basic requirements for constituent materials
5.1.1 General
5.1.2 Cement
5.1.3 Aggregates
5.1.4 Mixing water
5.1.5 Admixtures
5.1.6 Additions (including mineral fillers and
pigments)
5.2 Basic requirements for composition of concrete
5.2.1 General
5.2.2 Selection of cement
5.2.3 Use of aggregates
5.2.4 Use of recycled water
5.2.5 Use of additions
5.2.6 Use of admixtures
5.2.7 Chloride content
5.2.8 Concrete temperature
5.3 Requirements related to exposure classes
5.3.1 General
5.3.2 Limiting values for concrete composition
5.3.3 Performance-related design methods
5.4 Requirements for fresh concrete
5.4.1 Consistence
5.4.2 Cement content and water/cement ratio
5.4.3 Air content
5.4.4 Maximum aggregate size
5.5 Requirements for hardened concrete
5.5.1 Strength
5.5.2 Density
5.5.3 Resistance to water penetration
5.5.4 Reaction to fire
6 Specification of concrete
6.1 General
6.2 Specification for designed concrete
6.2.1 General
6.2.2 Basic requirements
6.2.3 Additional requirements
6.3 Specification for prescribed concrete
6.3.1 General
6.3.2 Basic requirements
6.3.3 Additional requirements
6.4 Specification of standardized prescribed concrete
7 Delivery of fresh concrete
7.1 Information from the user of the concrete to the
producer
7.2 Information from the producer of the concrete to
the user
7.3 Delivery ticket for ready-mixed concrete
7.4 Delivery information for site-mixed concrete
7.5 Consistence at delivery
8 Conformity control and conformity criteria
8.1 General
8.2 Conformity control for designed concrete
8.2.1 Conformity control for compressive strength
8.2.2 Conformity control for tensile splitting
strength
8.2.3 Conformity control for properties other than
strength
8.3 Conformity control of prescribed concrete including
standardized prescribed concrete
8.4 Actions in the case of non-conformity of the product
9 Production control
9.1 General
9.2 Production control systems
9.3 Recorded data and other documents
9.4 Testing
9.5 Concrete composition and initial testing
9.6 Personnel, equipment and installation
9.6.1 Personnel
9.6.2 Equipment and installation
9.7 Batching of constituent materials
9.8 Mixing of concrete
9.9 Production control procedures
10 Evaluation of conformity
10.1 General
10.2 Assessment, surveillance and certification of
production control
11 Designation for designed concrete
Annex A (normative) Initial test
Annex B (normative) Identity testing for compressive
strength
Annex C (normative) Provisions for assessment, surveillance
and certification of production control
Annex D (informative) Bibliography
Annex E (informative) Guidance on the application of the
equivalent performance concept of concrete properties
Annex F (informative) Recommendations for limiting values
of concrete compositions
Annex H (informative) Additional provisions for high
strength concrete
Annex J (informative) Performance-related design methods
with respect to durability
Annex K (informative) Concrete families
Annex NA (informative) National Annex to I.S. EN 206-1:2002
Annex NB (informative) Standardized prescribed mixes
Annex NC (informative) Alternative limiting values for varying
minimum covers and cement types/combinations
Annex ND (informative) Forms for specifying or scheduling
concrete mixes in accordance with I.S. EN 206-1
Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.