03/108624 DC : DRAFT JULY 2003
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
IEC 60300-3-2 - DEPENDABILITY MANAGEMENT - PART 3-2: APPLICATION GUIDE - COLLECTION OF DEPENDABILITY DATA FROM THE FIELD
Published date
23-11-2012
Publisher
Superseded date
14-04-2005
Superseded by
Sorry this product is not available in your region.
| Committee |
DS/1
|
| DocumentType |
Draft
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| IEC 61123:1991 | Reliability testing - Compliance test plans for success ratio |
| IEC 60863:1986 | Presentation of reliability, maintainability and availability predictions |
| ISO 2859-3:2005 | Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures |
| IEC 60605-4:2001 | Equipment reliability testing - Part 4: Statistical procedures for exponential distribution - Point estimates, confidence intervals, prediction intervals and tolerance intervals |
| IEC 60319:1999 | Presentation and specification of reliability data for electronic components |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 60300-3-3:2017 | Dependability management - Part 3-3: Application guide - Life cycle costing |
| ISO 3951:1989 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| IEC 61649:2008 | Weibull analysis |
| IEC 61014:2003 | Programmes for reliability growth |
| IEC 60605-6:2007 | Equipment reliability testing - Part 6: Tests for the validity and estimation of the constant failure rate and constant failure intensity |
| IEC 60706-3:2006 | Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data |
| IEC 61078:2016 | Reliability block diagrams |
| IEC 61165:2006 | Application of Markov techniques |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| ISO 2859-0:1995 | Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
| IEC 61163-1:2006 | Reliability stress screening - Part 1: Repairable assemblies manufactured in lots |
| ISO 8422:2006 | Sequential sampling plans for inspection by attributes |
| IEC 61124:2012 | Reliability testing - Compliance tests for constant failure rate and constant failure intensity |
| IEC 60300-3-1:2003 | Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
| ISO/TR 8550:1994 | Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots |
| IEC 61164:2004 | Reliability growth - Statistical test and estimation methods |
| IEC 61703:2016 | Mathematical expressions for reliability, availability, maintainability and maintenance support terms |
| IEC 60300-3-7:1999 | Dependability management - Part 3-7: Application guide - Reliability stress screening of electronic hardware |
| IEC 60300-3-9:1995 | Dependability management - Part 3: Application guide - Section 9: Risk analysis of technological systems |
| IEC 60706-5:2007 | Maintainability of equipment - Part 5: Testability and diagnostic testing |
| IEC 61650:1997 | Reliability data analysis techniques - Procedures for comparison of two constant failure rates and two constant failure (event) intensities |
| IEC 60706-6:1994 | Guide on maintainability of equipment - Part 6: Section 9: Statistical methods in maintainability evaluation |
| IEC 61710:2013 | Power law model - Goodness-of-fit tests and estimation methods |
| IEC 60300-3-5:2001 | Dependability management - Part 3-5: Application guide - Reliability test conditions and statistical test principles |
Summarise
Sorry this product is not available in your region.