09/30192800 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 29262 - PRODUCTION EQUIPMENT FOR MICROSYSTEMS - INTERFACE BETWEEN GRIPPERS AND HANDLING SYSTEM
Hardcopy , PDF
English
31-03-2011
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Interface definitions
5.1 Coordinate System
5.2 Layer 1: Mechanical interface
5.3 Layer 2: Service interface
5.4 Layer 3: Bus interface part
5.5 Tolerances
5.6 Load bearing capacities
5.7 Designation
Annex A (normative) - Tests procedure for fixation interface
[p][R]
Bibliography
| Committee |
MTE/1
|
| DocumentType |
Draft
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| DIN 32564-1:2004-05 | Production equipment for micro-systems - Terms and definitions - Part 1: General terms of micro-system technology |
| IEC 61784-1:2014 | Industrial communication networks - Profiles - Part 1: Fieldbus profiles |
| DIN 509:2006-12 | Technical drawings - Undercuts - Types and dimensions |
| EN 50295:1999 | Low-voltage switchgear and controlgear - Controller and device interface systems - Actuator Sensor interface (AS-i) |
| ISO/IEC 24702:2006 | Information technology — Generic cabling — Industrial premises |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| IEEE 802.3-2012 | IEEE Standard for Ethernet |
| TIA/EIA 568-2 : C2009 AMD 1 2016 | COMMERCIAL BUILDING TELECOMMUNICATIONS CABLING STANDARD - PART 2: BALANCED TWISTED-PAIR TELECOMMUNICATIONS CABLING AND COMPONENTS STANDARDS |
| ISO/IEC 11801:2002 | Information technology — Generic cabling for customer premises |
| ISO 9409-2:2002 | Manipulating industrial robots — Mechanical interfaces — Part 2: Shafts |
| IEC 62026-2:2008 | Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i) |
| ISO 3650:1998 | Geometrical Product Specifications (GPS) — Length standards — Gauge blocks |
| ISO 286-1:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
| ISO 9409-1:2004 | Manipulating industrial robots — Mechanical interfaces — Part 1: Plates |
| ISO 286-2:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| ISO/IEC 24740:2008 | Information technology — Responsive Link (RL) |
| ISO 9787:2013 | Robots and robotic devices — Coordinate systems and motion nomenclatures |
| IEC 61131-2:2017 | Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests |
| EN 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| DIN 7154-1:1966-08 | ISO-FITS FOR THE HOLE BASIS SYSTEM; TOLERANCE ZONES, DEVIATIONS |
| ISO 8734:1997 | Parallel pins, of hardened steel and martensitic stainless steel (Dowel pins) |
| DIN 7154-2:1966-08 | ISO-FITS FOR THE HOLE BASIC SYSTEM; TOLERANCES OF FIT (CLEARANCES AND INTERFERENCES) |
| IEC TR 60479-3:1998 | Effects of current on human beings and livestock - Part 3: Effects of currents passing through the body of livestock |
| ISO 18265:2013 | Metallic materials — Conversion of hardness values |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.