13/30286091 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 16678 - SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA
Hardcopy , PDF
English
30-11-2015
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Units of measurement and test conditions
6 Construction requirements
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Gas connections in common use
in the various countries
Annex B (informative) - Leak-tightness test - volumetric
method
Annex C (normative) - Leak-tightness test - pressure loss
method
Annex D (normative) - Conversion of pressure loss into
leakage rate
Annex E (normative) - Electrical/electronic component
fault modes
Annex F (normative) - Additional requirements for safety
accessories and pressure accessories
as defined in EU Directive 97/23/EC
Annex G (informative) - Materials for pressurized parts
Annex H (informative) - Additional materials for
pressurized parts
Annex I (normative) - Requirements for controls used in
DC supplied gas burners and gas burning appliances
Annex J (normative) - Method for the determination of a
Safety Integrity Level (SIL)
Annex K (normative) - Method for the determination of a
Performance Level (PL)
Annex L (informative) - Relationship between Safety Integrity
Level (SIL) and Performance Level (PL)
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
EU Directive 2009/142/EC relating to appliances
burning gaseous fuels
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of Pressure
Equipment Directive 97/23/EC
Bibliography
BS EN 16678.
| Committee |
GSE/22
|
| DocumentType |
Draft
|
| Pages |
44
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 16678 : DRAFT 2013 | Identical |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 175301-803:2006 | Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable |
| EN 14917:2009+A1:2012 | Metal bellows expansion joints for pressure applications |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN 1759-4:2003 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| 2009/142/EC : 2009 | DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 30 NOVEMBER 2009 RELATING TO APPLIANCES BURNING GASEOUS FUELS (TEXT WITH EEA RELEVANCE) |
| ISO 8573-1:2010 | Compressed air — Part 1: Contaminants and purity classes |
| EN 13906-2:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs |
| EN 1092-4:2002 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| EN 50156-1:2015 | Electrical equipment for furnaces and ancillary equipment - Part 1: Requirements for application design and installation |
| EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| EN 12760:2016 | Industrial valves - Socket welding ends for steel valves |
| PREN 12266-1 : DRAFT 2009 | INDUSTRIAL VALVES - TESTING OF METALLIC VALVES - PART 1: PRESSURE TESTS, TEST PROCEDURES AND ACCEPTANCE CRITERIA - MANDATORY REQUIREMENTS |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| EN 13787:2001 | Elastomers for gas pressure regulators and associated safety devices for inlet pressures up to 100 bar |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.