15/30313602 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 25649-7 - FLOATING LEISURE ARTICLES FOR USE ON AND IN THE WATER - PART 7: ADDITIONAL SPECIFIC SAFETY REQUIREMENTS AND TEST METHODS FOR CLASS E DEVICES
Hardcopy , PDF
English
31-10-2017
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Construction and functional components of boats
6 Safety requirements and test methods
7 Performance requirements and test methods for boats
8 Standard equipment and accessories for boats
9 Marking
10 Instructions for use for boats
11 Exclusions
Annex A (normative) - Inflatable canoes, kayaks and
sit-on-top kayaks
Annex B (normative) - Inflatable boat propelled by sail
or motor
Annex C (informative) - General arrangement of a typical
boat with the hull made of non-reinforced material
Annex D (informative) - General arrangement of a typical
boat with the hull made of reinforced material
Annex E (informative) - General arrangement of a typical
paddle boat/kayak
Annex F (informative) - Examples of typical products forming
Class E
Bibliography
BS ISO 25649-7.
| Committee |
SW/136/22
|
| DocumentType |
Draft
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| EN ISO 6185-1:2001 | Inflatable boats - Part 1: Boats with a maximum motor power rating of 4,5 kW (ISO 6185-1:2001) |
| EN 13138-3:2014 | Buoyant aids for swimming instruction - Part 3: Safety requirements and test methods for swim seats to be worn |
| EN ISO 8665:2017 | Small craft - Marine propulsion reciprocating internal combustion engines - Power measurements and declarations (ISO 8665:2006) |
| EN ISO 6185-2:2001 | Inflatable boats - Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive (ISO 6185-2:2001) |
| ISO 4646:1989 | Rubber- or plastics-coated fabrics — Low-temperature impact test |
| ISO 6185-1:2001 | Inflatable boats — Part 1: Boats with a maximum motor power rating of 4,5 kW |
| EN 13138-2:2014 | Buoyant aids for swimming instruction - Part 2: Safety requirements and test methods for buoyant aids to be held |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| ISO 6185-3:2014 | Inflatable boats — Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing |
| EN 71-1:2014 | Safety of toys - Part 1: Mechanical and physical properties |
| EN ISO 6185-3:2014 | Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater (ISO 6185-3:2014) |
| ISO 13857:2008 | Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 8665:2006 | Small craft — Marine propulsion reciprocating internal combustion engines — Power measurements and declarations |
| ISO 6185-2:2001 | Inflatable boats — Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive |
| ISO 3011:1997 | Rubber- or plastics-coated fabrics — Determination of resistance to ozone cracking under static conditions |
| EN 837-3:1996 | Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing |
| EN 13138-1:2014 | Buoyant aids for swimming instruction - Part 1: Safety requirements and test methods for buoyant aids to be worn |
| EN ISO 4892-2:2013 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.