16/30310949 DC : 0
NA
Status of Standard is Unknown
BS ISO 5910 - CARDIOVASCULAR IMPLANTS AND EXTRACOPOREAL SYSTEMS - CARDIAC VALVE REPAIR DEVICES
Hardcopy , PDF
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations
5 Fundamental requirements
6 Device description
7 Design verification testing and
analysis/Design validation
Annex A (informative) - Rationale for the
provisions of this International Standard
Annex B (informative) - Examples of heart valve
repair devices and delivery systems
Annex C (normative) - Packaging
Annex D (normative) - Product labels, instructions
for use, and training
Annex E (normative) - Sterilization
Annex F (informative) - Heart valve repair system
characteristics
Annex G (informative) - Heart valve repair system
hazards, associated failure modes and
evaluation methods
Annex H (informative) - In vitro test guidelines for
paediatric devices
Annex I (informative) - Examples and definitions of
some physical and material properties of heart
valve repair devices and their components
Annex J (informative) - Examples of Standards
applicable to testing of materials and
components of heart valve repair devices
Annex K (informative) - Considerations for device
material properties undergoing alterations
post implantation
Annex L (informative) - Corrosion assessment
Annex M (informative) - Guidelines for in vitro
evaluation of functional performance
of the repair
Annex N (informative) - Durability testing
Annex O (informative) - Fatigue assessment
Annex P (informative) - Preclinical in vivo evaluation
Annex Q (normative) - Adverse event classification
during clinical investigation
Annex R (informative) - Imaging protocol
Annex S (informative) - Clinical investigation endpoints
for valve repair devices: Suggestions for
endpoints and their timing
Annex T (informative) - Additional device design
evaluation requirements
Annex U (informative) - Guidelines for delivery
system design evaluation testing
Bibliography
BS ISO 5910.
| Committee |
CH/150/2
|
| DocumentType |
Draft
|
| Pages |
125
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 11137-1:2006 | Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 11607-2:2006 | Packaging for terminally sterilized medical devices — Part 2: Validation requirements for forming, sealing and assembly processes |
| ISO 15223-2:2010 | Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation |
| ISO 14160:2011 | Sterilization of health care products — Liquid chemical sterilizing agents for single-use medical devices utilizing animal tissues and their derivatives — Requirements for characterization, development, validation and routine control of a sterilization process for medical devices |
| ISO 11135:2014 | Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices |
| IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
| ISO 13485:2016 | Medical devices — Quality management systems — Requirements for regulatory purposes |
| ISO 14937:2009 | Sterilization of health care products — General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| ISO 10993-2:2006 | Biological evaluation of medical devices — Part 2: Animal welfare requirements |
| ISO 5840-1:2015 | Cardiovascular implants — Cardiac valve prostheses — Part 1: General requirements |
| ISO 25539-1:2017 | Cardiovascular implants — Endovascular devices — Part 1: Endovascular prostheses |
| ISO 22442-1:2015 | Medical devices utilizing animal tissues and their derivatives — Part 1: Application of risk management |
| IEC 62366:2007+AMD1:2014 CSV | Medical devices - Application of usability engineering to medical devices |
| ISO 14630:2012 | Non-active surgical implants — General requirements |
| ISO/TS 11139:2006 | Sterilization of health care products — Vocabulary |
| ISO 11137-3:2017 | Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control |
| ISO 5840-3:2013 | Cardiovascular implants — Cardiac valve prostheses — Part 3: Heart valve substitutes implanted by transcatheter techniques |
| ISO 10993-1:2009 | Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk management process |
| ISO 10555-1:2013 | Intravascular catheters — Sterile and single-use catheters — Part 1: General requirements |
| ISO 22442-2:2015 | Medical devices utilizing animal tissues and their derivatives — Part 2: Controls on sourcing, collection and handling |
| ISO 14155:2011 | Clinical investigation of medical devices for human subjects — Good clinical practice |
| ISO 22442-3:2007 | Medical devices utilizing animal tissues and their derivatives — Part 3: Validation of the elimination and/or inactivation of viruses and transmissible spongiform encephalopathy (TSE) agents |
| ISO 14971:2007 | Medical devices — Application of risk management to medical devices |
| ISO 11607-1:2006 | Packaging for terminally sterilized medical devices — Part 1: Requirements for materials, sterile barrier systems and packaging systems |
| ISO 5840-2:2015 | Cardiovascular implants — Cardiac valve prostheses — Part 2: Surgically implanted heart valve substitutes |
| ISO 15223-1:2016 | Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Part 1: General requirements |
| ISO 17664:2017 | Processing of health care products — Information to be provided by the medical device manufacturer for the processing of medical devices |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.