16/30312922 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 18888 - GAS TURBINE COMBINED CYCLE POWER PLANTS THERMAL PERFORMANCE TESTS
Hardcopy , PDF
English
31-10-2017
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test boundary
5 Symbols and units
6 Preparation for test
7 Execution of test
8 Calculation of results for absolute test
9 Part load tests
10 Calculation of results for comparative test
11 Test report
Annex A (informative) - Typical secondary
variables
Annex B (informative) - Numerical examples of
uncertainty calculation
Annex C (normative) - Procedure for power factor
conversion
Bibliography
BS ISO 18888.
| Committee |
MCE/16
|
| DocumentType |
Draft
|
| Pages |
79
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 10715:1997 | Natural gas — Sampling guidelines |
| ISO 6976:2016 | Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition |
| ISO 3675:1998 | Crude petroleum and liquid petroleum products — Laboratory determination of density — Hydrometer method |
| ISO 12242:2012 | Measurement of fluid flow in closed conduits — Ultrasonic transit-time meters for liquid |
| ISO 3977-1:1997 | Gas turbines — Procurement — Part 1: General introduction and definitions |
| ISO 11086:1996 | Gas turbines — Vocabulary |
| ASTM D 4868 : 2017 : REDLINE | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ISO 3977-9:1999 | Gas turbines — Procurement — Part 9: Reliability, availability, maintainability and safety |
| ISO 6975:1997 | Natural gas — Extended analysis — Gas-chromatographic method |
| ISO 2533:1975 | Standard Atmosphere |
| ISO 6974-3:2000 | Natural gas — Determination of composition with defined uncertainty by gas chromatography — Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two packed columns |
| DIN 51900-1:2000-04 | Determining the gross calorific value of solid and liquid fuels using the bomb calorimeter, and calculation of net calorific value - Part 1: General information |
| ISO 5167:1980 | Measurement of fluid flow by means of orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full |
| ISO 12185:1996 | Crude petroleum and petroleum products — Determination of density — Oscillating U-tube method |
| ISO 2314:2009 | Gas turbines — Acceptance tests |
| ISO 6817:1992 | Measurement of conductive liquid flow in closed conduits — Method using electromagnetic flowmeters |
| IEC 60751:2008 | Industrial platinum resistance thermometers and platinum temperature sensors |
| ISO 10790:2015 | Measurement of fluid flow in closed conduits — Guidance to the selection, installation and use of Coriolis flowmeters (mass flow, density and volume flow measurements) |
| ISO 6974-1:2012 | Natural gas — Determination of composition and associated uncertainty by gas chromatography — Part 1: General guidelines and calculation of composition |
| ISO 17089-1:2010 | Measurement of fluid flow in closed conduits - Ultrasonic meters for gas — Part 1: Meters for custody transfer and allocation measurement |
| ISO 12213-2:2006 | Natural gas — Calculation of compression factor — Part 2: Calculation using molar-composition analysis |
| ISO 20765-2:2015 | Natural gas — Calculation of thermodynamic properties — Part 2: Single-phase properties (gas, liquid, and dense fluid) for extended ranges of application |
| ASTM D 1945 : 2014 : REDLINE | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
| ISO 20765-1:2005 | Natural gas — Calculation of thermodynamic properties — Part 1: Gas phase properties for transmission and distribution applications |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.