• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7966/D7966M : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Resistance to Creep of Adhesives in Static Shear by Compression Loading (Wood-to-Wood)
Available format(s)

Hardcopy , PDF

Superseded date

09-06-2023

Language(s)

English

Published date

30-06-2016

1.1This test method covers the determination of creep properties of structural adhesives in wood-to-wood bonds when a standardized specimen is subjected to shearing stresses at various levels of static load, constant temperature, and relative humidity. Apparatus and procedures are provided for shear deformation (creep) of adhesive bonds under static load. This test method is used under the indicated conditions to evaluate resistance to creep properties of a structural wood adhesive.

1.2The test method is used to evaluate creep performance of adhesives suitable for the bonding of wood, including treated wood, into structural wood products for general construction, marine use, or for other uses where a high-strength general construction, creep-resistant, durable adhesive bond is required. Individual block shear specimens are prepared from adhesively bonded laminations, subjected to a constant load under various combinations of temperature and relative humidity, and the amount of creep measured.

1.3Creep of structural wood adhesives as measured by this test method may not be comparative to other ASTM methods and is limited to the conditions of the test and procedures contained herein.

1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 14
DocumentType
Test Method
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 2559 : 2009 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions
ASTM D 4442 : 2007 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
ASTM D 2395 : 1993 : R1997 : EDT 2 Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials
ASTM D 907 : 2015 Standard Terminology of Adhesives
ASTM D 4442 : 2015 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM D 905 : 2008 : R2021 Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading
ASTM D 2559 : 2004 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions
ASTM D 905 : 2008 : R2013 Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading
ASTM D 1101 : 1997 : REV A Standard Test Methods for Integrity of Adhesive Joints in Structural Laminated Wood Products for Exterior Use
ASTM D 4442 : 2016 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM D 2395 : 2017 : R2022 Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials
ASTM D 2395 : 1993 : R1997 : EDT 1 Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials
ASTM D 2395 : 2007 : REV A Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials
ASTM D 907 : 2015 : R2023 Standard Terminology of Adhesives
ASTM D 2395 : 2017 Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials
ASTM D 2559 : 2010 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions
ASTM D 4442 : 2020 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM D 2395 : 2014 : EDT 1 Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials
ASTM D 2395 : 2014 Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM D 2395 : 2006 Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials
ASTM D 2559 : 2012 : REV A : EDT 1 Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions
ASTM D 1101 : 1997 : REV A : R2013 Standard Test Methods for Integrity of Adhesive Joints in Structural Laminated Wood Products for Exterior Use
ASTM D 905 : 1998 Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading
ASTM D 2559 : 2000 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions
ASTM D 2559 : 2012 : REV A Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions
ASTM D 2395 : 2007 : REV A : EDT 1 Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials
ASTM D 2559 : 2003 Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions
ASTM D 2559 : 2012 : REV A : R2018 Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions
ASTM D 2559 : 2010 : REV A Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions
ASTM D 1101 : 1997 : REV A : R2006 Standard Test Methods for Integrity of Adhesive Joints in Structural Laminated Wood Products for Exterior Use
ASTM D 2395 : 2002 Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials
ASTM D 4442 : 1992 : R1997 : EDT 1 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
ASTM D 4442 : 1984 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
ASTM D 1101 : 1997 : REV A : R2018 Standard Test Methods for Integrity of Adhesive Joints in Structural Laminated Wood Products for Exterior Use
ASTM D 4442 : 1992 : R2003 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.