• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 8076 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines
Available format(s)

Hardcopy , PDF

Superseded date

03-01-2020

Language(s)

English

Published date

01-04-2018

1.1This specification covers the requirements of a high octane number test fuel suitable for spark-ignition engines to be utilized in ground vehicles that will require 100 research octane number (RON) minimum rated fuel.

1.1.1The fuels described by this specification are intended for developing technologies that lead to reduced vehicle energy consumption, such as higher compression ratio, higher power density, increased turbocharger boost pressure, smaller swept displacement volume, and operation at lower engine speeds.

1.1.2The fuels described in this test fuel specification may not meet all of the performance or regulatory requirements for use in vehicles using commercial gasoline.

1.2The fuels covered in this specification may contain oxygenates, such as alcohols and ethers, up to 50 % by volume. This specification covers fuels that may contain both fossil and bio-derived components.

1.3This specification provides a description of high RON test fuel for automotive spark-ignition engines that are not currently in the marketplace but are being developed and require a defined standard test fuel. The high RON fuel could become available in the marketplace if/when such engines are introduced in commerce. The specification is under continuous review, which can result in revisions based on changes in fuel, automotive requirements, or test methods, or a combination thereof. All users of this specification, therefore, should refer to the latest edition.

Note 1:If there is any doubt as to the latest edition of Specification D8076, contact ASTM International Headquarters.

1.4The values stated in SI units are the standard.

1.4.1Exception—Non-SI values are provided for information only. U.S. federal regulations frequently specify non-SI units.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4175 : 2014 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 2622 : 1992 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 4175 : 2009 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2699 : 2016 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2011 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2008 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5453 : 2009 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4806 : 2002 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 1995 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 2622 : 1987 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 4175 : 2005 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2016 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2004 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 1999 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 7039 : 2013 Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 3120 : 1996 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 5983 : 2013 Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2005 : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7667 : 2010 : EDT 1 Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method
ASTM D 2700 : 2009 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2018 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 7220 : 2012 Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 4814 : 2016 : REV C Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2004 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 1152 : 2006 : R2012 Standard Specification for Methanol (Methyl Alcohol) (Withdrawn 2021)
ASTM D 2700 : 2011 : EDT 1 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 3120 : 2008 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 4177 : 2016 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 5453 : 2008 : REV B Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 2699 : 2007 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5453 : 2000 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 2700 : 2007 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4176 : 1993 : R1997 Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)
ASTM D 2699 : 2013 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2015 : REV C Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7862 : 2015 : REV A Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 1266 : 1998 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM D 7220 : 2012 : R2017 Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 4815 : 2015 : REV B Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 5191 : 2018 : REV A Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 4814 : 2014 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 6920 : 2013 Standard Test Method for Total Sulfur in Naphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels by Oxidative Combustion and Electrochemical Detection (Withdrawn 2018)
ASTM D 7862 : 2019 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2017 : REV A : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2699 : 2017 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4814 : 2001 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2007 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5482 : 2007 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method<span class='unicode'>—</span>Atmospheric)
ASTM D 4814 : 2004 : REV B : EDT 1 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 3831 : 2012 Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy
ASTM D 5453 : 2004 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 6378 : 2018 : REV A Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 2700 : 2014 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4814 : 2015 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2000 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2700 : 2009 : EDT 1 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4177 : 1995 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 2700 : 2007 : REV B Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 7319 : 2011 : EDT 1 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography
ASTM D 4175 : 2008 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4057 : 2012 : R2018 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 5453 : 2012 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4953 : 2015 Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
ASTM D 5599 : 2000 : R2010 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 4814 : 2011 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4306 : 1997 Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 4175 : 2017 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4306 : 2015 Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 4175 : 2009 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6378 : 2008 Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 5842 : 2014 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 1266 : 2013 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM D 5191 : 2006 : EDT 1 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4806 : 2015 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 1152 : 2006 Standard Specification for Methanol (Methyl Alcohol)
ASTM D 2622 : 1998 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4806 : 2006 : REV B Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2018 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2700 : 2013 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 1992 Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method
ASTM D 5854 : 1996 : R2010 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 3237 : 2006 : EDT 1 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 2700 : 2010 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2003 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 1992 Standard Test Method for Knock Characteristics of Motor and Aviation Fuels by the Motor Method
ASTM D 6920 : 2003 Standard Test Method for Total Sulfur in Naphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels by Oxidative Combustion and Electrochemical Detection
ASTM D 4175 : 2009 : REV A : EDT 4 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7618 : 2010 Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel
ASTM D 5842 : 2004 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 4175 : 2009 : REV A : EDT 3 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2699 : 2001 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4806 : 2006 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 1981 : EDT 2 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 5453 : 2008 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4814 : 2018 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2003 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5854 : 2019 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 5599 : 2018 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 1266 : 1987 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM D 7862 : 2013 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4306 : 2001 Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 4814 : 1995 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2009 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2622 : 2008 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 5845 : 2001 : R2016 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <emph type="ital">tert</emph>-Butanol in Gasoline by Infrared Spectroscopy
ASTM D 5059 : 1998 Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy
ASTM D 4175 : 2018 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4814 : 2016 : REV : EDT 0 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4306 : 2007 Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 4806 : 2006 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 2700 : 2012 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4806 : 2001 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2009 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2001 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 2700 : 2012 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 1999 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2001 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2014 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5453 : 2005 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 2700 : 2017 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5854 : 1996 : R2005 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 5842 : 1995 : R2000 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 4175 : 2001 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2005 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5845 : 1995 : R2000 : EDT 1 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <i>tert-</i>Butanol in Gasoline by Infrared Spectroscopy
ASTM D 2700 : 2016 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4814 : 2012 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2004 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 2700 : 2001 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4814 : 2016 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5191 : 2010 : REV A Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 7862 : 2015 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2013 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7328 : 2013 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 2699 : 2012 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 7667 : 2010 Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel<char: emdash>Thin Silver Strip Method
ASTM D 3120 : 2008 : R2019 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 6378 : 2010 Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 4814 : 2010 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2003 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2002 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 3237 : 2002 Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy
ASTM D 4814 : 2001 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2700 : 2006 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4806 : 2001 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2016 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5453 : 2006 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4814 : 2008 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2003 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4953 : 1999 : REV A Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
ASTM D 4176 : 2004 : R2009 Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)
ASTM D 7319 : 2007 Standard Test Method for Determination of Total and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography
ASTM D 4814 : 2003 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5059 : 2014 Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy
ASTM D 4806 : 2008 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 2006 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4806 : 2018 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7671 : 2010 : EDT 1 Standard Test Method for Corrosiveness to Silver by Automotive Spark–Ignition Engine Fuel–Silver Strip Method
ASTM D 2699 : 2011 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2015 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2002 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2017 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4177 : 2015 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 5983 : 1997 : R2002 Standard Specification for Methyl <I>Tertiary</I>-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2010 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2004 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2016 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 3120 : 2003 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 5191 : 2012 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4306 : 2012 : REV A Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 4806 : 2011 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2012 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4953 : 2006 : R2012 Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
ASTM D 2699 : 2008 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2013 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5845 : 2001 : R2006 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <i>tert</i>-Butanol in Gasoline by Infrared Spectroscopy
ASTM D 4814 : 2010 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2008 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 2012 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 5845 : 2001 : R2011 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <span class="italic">tert</span>-Butanol in Gasoline by Infrared Spectroscopy
ASTM D 4815 : 1999 : EDT 1 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 2700 : 2018 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2003 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 2622 : 2003 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 3831 : 2001 Standard Test Method for Manganese In Gasoline By Atomic Absorption Spectroscopy
ASTM D 4806 : 2016 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5453 : 2016 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 5059 : 2014 : R2019 Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy
ASTM D 4175 : 2009 : REV A : EDT 5 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6920 : 2007 Standard Test Method for Total Sulfur in Naphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels by Oxidative Combustion and Electrochemical Detection
ASTM D 4175 : 2016 : REV C Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4306 : 2012 : REV B Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 2700 : 2016 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2015 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2699 : 2003 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2003 : REV B Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 1999 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 7319 : 2017 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
ASTM D 4814 : 2009 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 7039 : 2015 : REV A Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 7618 : 2013 Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel
ASTM D 5983 : 2006 : R2011 Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2018 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 7319 : 2009 Standard Test Method for Determination of Total and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography
ASTM D 2700 : 2011 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2015 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 3120 : 2003 : REV A Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 7328 : 2016 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 4814 : 2011 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 7039 : 2004 Standard Test Method for Sulfur in Gasoline and Diesel Fuel by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4806 : 2007 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4815 : 2009 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 4806 : 2019 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2004 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2010 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6378 : 1999 : EDT 1 Standard Test Method for Determination of Vapor Pressure (VP<sub>x</sub>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 5453 : 2003 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 7667 : 2010 : EDT 2 Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method
ASTM D 4814 : 2008 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2009 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5983 : 2006 Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2011 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4815 : 2015 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 4814 : 2002 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4815 : 2004 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 4175 : 2016 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4814 : 2011 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4815 : 1999 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 2700 : 2002 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5842 : 2004 : R2009 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 2700 : 2007 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4177 : 1995 : R2010 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4814 : 2019 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2013 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2002 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6378 : 2006 Standard Test Method for Determination of Vapor Pressure (VP<sub>X</sub>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 4175 : 2008 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2019 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6378 : 2003 Standard Test Method for Determination of Vapor Pressure (VP<sub>x</sub>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 4814 : 2006 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2007 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2002 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4814 : 2007 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5191 : 2018 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4177 : 1995 : R2000 Standard Practice for Automatic Sampling of Peroleum and Petroleum Products
ASTM D 5453 : 2016 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 3831 : 2001 : R2006 Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy
ASTM D 5191 : 2010 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4176 : 2004 : R2014 Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)
ASTM D 5059 : 2007 Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy
ASTM D 4175 : 2000 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4814 : 2018 : REV D Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2016 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5599 : 2015 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 7039 : 2015 Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4175 : 2016 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 3237 : 2006 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 4814 : 2006 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5599 : 2017 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 4806 : 2018 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5854 : 1996 : R2000 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 2700 : 2004 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4814 : 1992 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4815 : 2013 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 4814 : 2014 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2015 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 7319 : 2011 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography
ASTM D 7319 : 2012 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography
ASTM D 5191 : 2002 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 2699 : 2004 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2015 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2013 : REV B Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2013 : REV B Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5482 : 1999 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method-Atmospheric)
ASTM D 5482 : 2001 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method-Atmospheric)
ASTM D 4814 : 2007 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2622 : 2010 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 5191 : 2019 Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 4814 : 2009 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5599 : 2000 : R2005 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 4806 : 2008 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7039 : 2007 Standard Test Method for Sulfur in Gasoline and Diesel Fuel by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2699 : 2001 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2006 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4815 : 2003 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 4814 : 2018 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2013 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2006 : REV C Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5482 : 2007 : R2013 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method—Atmospheric)
ASTM D 6378 : 2010 : R2016 Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 4814 : 2016 : REV D Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2017 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2000 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5453 : 2019 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 3120 : 1996 : R2002 : EDT 1 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 7328 : 2007 Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 2699 : 2015 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2622 : 2007 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 5059 : 2013 Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy
ASTM D 7220 : 2006 Standard Test Method for Sulfur in Automotive Fuels by Polarization X-ray Fluorescence Spectrometry
ASTM D 4175 : 2017 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4814 : 2013 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 3120 : 2006 : EDT 1 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 7862 : 2018 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4306 : 2013 Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 2622 : 1994 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 4814 : 2004 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 3120 : 2006 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 2699 : 2002 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 7328 : 2011 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 4175 : 2009 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2622 : 2005 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2700 : 2017 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 7667 : 2010 : R2015 Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method
ASTM D 7328 : 2017 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 4177 : 2016 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 7671 : 2010 Standard Test Method for Corrosiveness to Silver by Automotive Spark<span class='unicode'>–</span>Ignition Engine Fuel<span class='unicode'>–</span>Silver Strip Method
ASTM D 4806 : 2009 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 2700 : 2003 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2004 : REV A Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4806 : 2012 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4177 : 1995 : R2005 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 3237 : 2017 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 5453 : 2019 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4175 : 2018 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2016 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7671 : 2010 : R2015 Standard Test Method for Corrosiveness to Silver by Automotive Spark–Ignition Engine Fuel–Silver Strip Method
ASTM D 3831 : 1998 Standard Test Method for Manganese In Gasoline By Atomic Absorption Spectroscopy
ASTM D 2699 : 2009 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5599 : 2000 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 2699 : 2004 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2006 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5854 : 2019 : REV A Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 4814 : 1993 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 3237 : 1997 Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy
ASTM D 5983 : 2017 Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel
ASTM D 5842 : 2017 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 4806 : 2010 : REV B Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5191 : 2007 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 2700 : 2004 : EDT 1 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4057 : 1995 : R2000 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 1152 : 1997 Standard Specification for Methanol (Methyl Alcohol)
ASTM D 3120 : 2008 : R2014 Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry
ASTM D 2700 : 2001 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 6378 : 2007 : EDT 1 Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 5191 : 2015 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4814 : 2014 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 6378 : 2018 Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 2699 : 2018 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2017 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4815 : 2015 : REV A Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 4806 : 1999 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7618 : 2013 : R2017 Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel
ASTM D 3831 : 2012 : R2017 Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy
ASTM D 4175 : 2019 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 1266 : 2007 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM D 4177 : 2015 : REV A Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4176 : 2004 : EDT 1 Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)
ASTM D 4814 : 2018 : REV C Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2013 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2019 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4176 : 2002 Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)
ASTM D 4057 : 2006 : R2011 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4175 : 2015 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5191 : 2010 : REV B Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 5845 : 2001 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <i>tert-</i>Butanol in Gasoline by Infrared Spectroscopy
ASTM D 5983 : 2015 Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel
ASTM D 6378 : 2007 Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 5453 : 2003 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 4814 : 2007 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 2699 : 2010 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2013 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 3237 : 2012 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 4953 : 2006 Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
ASTM D 7328 : 2007 : EDT 1 Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 5191 : 2006 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4814 : 2013 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 5854 : 1996 : R2015 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 2699 : 2019 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2004 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 1266 : 2018 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM D 7319 : 2013 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
ASTM D 4175 : 2008 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4306 : 2012 Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4176 : 2004 Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)
ASTM D 5983 : 1997 Standard Specification for Methyl <I>Tertiary</I>-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel
ASTM D 2700 : 2008 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5983 : 2018 Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Blending With Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5453 : 2008 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 7862 : 2017 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5453 : 2000 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 4306 : 2012 : REV C Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.