• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 8111 : 2019

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine

Available format(s)

Hardcopy , PDF

Superseded date

15-11-2019

Language(s)

English

Published date

01-05-2019

This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening (as measured by kinematic viscosity increase), piston deposits, ring sticking, oil consumption, and phosphorus retention.

1.1This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening (as measured by kinematic viscosity increase), piston deposits, ring sticking, oil consumption, and phosphorus retention. Such oils include both single-viscosity and multiviscosity grade oils that are used in both spark-ignition, gasoline-fueled engines, as well as in diesel engines.

1.1.1Additionally, with nonmandatory supplemental requirements, a Sequence IIIHA Test (Mini Rotary Viscometer and Cold Cranking Simulator measurements), or a Sequence IIIHB Test (phosphorus retention measurement) can be conducted. These supplemental test procedures are contained in Appendix X1 and Appendix X2, respectively.

Note 1:Companion test methods used to evaluate engine oil performance for specification requirements are discussed in SAE J304.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1Exceptions:

1.2.1.1Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing sizes, and valve sizes and springs.

1.2.1.2The ring end gaps in Table A8.7, the dimensions for the blowby ventilation support bracket in Fig. A3.2, and the torque wrenches in Table A8.1 are in inch-pound units.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are provided in 6.11.6, 7.1, 7.2.1, and 7.3.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Test Method
Pages
38
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7320 : 2011 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 4175 : 2014 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2003 : REV A Standard Specification for Performance of Engine Oils
ASTM D 4175 : 2009 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2699 : 2016 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4684 : 2002 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 2699 : 2011 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 3338 : 1992 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 4175 : 2008 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5453 : 2009 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 3343 : 2005 : R2010 Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D 4485 : 2006 Standard Specification for Performance of Engine Oils
ASTM D 4175 : 2005 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2011 : REV C Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2699 : 1999 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 1319 : 1989 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption
ASTM D 4175 : 2005 : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 1319 : 2008 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 2700 : 2009 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2018 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2004 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2011 : EDT 1 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2001 Standard Specification for Performance of Engine Oils
ASTM D 5453 : 2008 : REV B Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 2699 : 2007 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 3244 : 1997 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 5453 : 2000 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 2700 : 2007 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 3231 : 1999 Standard Test Method for Phosphorus in Gasoline
ASTM D 2699 : 2013 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5185 : 1997 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4175 : 2015 : REV C Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 3231 : 2013 Standard Test Method for Phosphorus in Gasoline
ASTM D 3244 : 2012 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 4815 : 2015 : REV B Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 5191 : 2018 : REV A Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 4175 : 2017 : REV A : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2699 : 2017 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2003 Standard Specification for Performance of Engine Oils
ASTM D 4052 : 1996 : R2002 : EDT 1 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 4485 : 2008 Standard Specification for Performance of Engine Oils
ASTM D 4739 : 2005 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 4485 : 2015 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5453 : 2004 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 1319 : 2018 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4485 : 2005 : REV A Standard Specification for Performance of Engine Oils
ASTM D 2700 : 2014 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4684 : 2008 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 2700 : 2009 : EDT 1 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2007 : REV B Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2008 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5453 : 2012 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4052 : 2018 : REV A Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 1319 : 2014 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2017 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2009 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2011 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 3244 : 2007 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 5293 : 2010 : EDT 1 Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between <span class='unicode'>–</span>5 and <span class='unicode'>–</span>35<span class='unicode'>°</span>C Using Cold-Cranking Simulator
ASTM D 3338 : 2000 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 5191 : 2006 : EDT 1 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 2700 : 2013 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 3338 : 2004 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 3343 : 2005 Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D 2699 : 1992 Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method
ASTM D 7320 : 2014 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 3237 : 2006 : EDT 1 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 1319 : 1999 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 2700 : 2010 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2018 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5185 : 2005 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 2700 : 2003 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 1992 Standard Test Method for Knock Characteristics of Motor and Aviation Fuels by the Motor Method
ASTM D 3244 : 2016 Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 4175 : 2009 : REV A : EDT 4 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2009 : REV A : EDT 3 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2699 : 2001 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 8047 : 2017 Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine
ASTM D 4052 : 2009 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5453 : 2008 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 5185 : 2002 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 2699 : 2003 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2011 : REV B Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4684 : 2007 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 4485 : 2016 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4175 : 2018 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4485 : 2007 Standard Specification for Performance of Engine Oils
ASTM D 2700 : 2012 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2010 Standard Specification for Performance of Engine Oils
ASTM D 2699 : 2009 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2001 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 5185 : 2018 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 2700 : 2012 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2001 : REV A Standard Specification for Performance of Engine Oils
ASTM D 2700 : 1999 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2001 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 1319 : 2002 : REV A Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 5453 : 2005 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 2700 : 2017 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4684 : 2017 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 8047 : 2018 Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine
ASTM D 4175 : 2001 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2005 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2700 : 2016 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2001 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2010 : REV A Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4739 : 2008 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 2699 : 2012 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 3231 : 2018 Standard Test Method for Phosphorus in Gasoline
ASTM D 4175 : 2002 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 3237 : 2002 Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy
ASTM D 5185 : 2013 : EDT 1 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 8047 : 2017 : REV A Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine
ASTM D 7320 : 2015 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 5452 : 2012 Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration
ASTM D 2700 : 2006 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2004 Standard Specification for Performance of Engine Oils
ASTM D 2699 : 2016 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5452 : 2000 Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration
ASTM D 5453 : 2006 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 5293 : 2014 Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –5°C and –35°C Using Cold-Cranking Simulator
ASTM D 7320 : 2016 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 4739 : 2017 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4684 : 2012 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 7320 : 2015 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 3231 : 2002 Standard Test Method for Phosphorus in Gasoline
ASTM D 4739 : 2006 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 2699 : 2011 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2015 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2000 Standard Specification for Performance of Engine Oils
ASTM D 4175 : 2002 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 3343 : 2005 : R2015 Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D 3343 : 2016 Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D 4739 : 1996 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 4052 : 2011 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5191 : 2012 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 2699 : 2012 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5293 : 2008 : EDT 1 Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator
ASTM D 2699 : 2008 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2013 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 1319 : 2003 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4052 : 2016 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 5452 : 2006 Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration
ASTM D 4485 : 2015 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 3343 : 1990 Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D 4815 : 1999 : EDT 1 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 2700 : 2018 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5185 : 2013 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 5191 : 2003 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 7320 : 2007 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 5293 : 2017 : REV A Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator
ASTM D 4684 : 2014 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 5452 : 2005 Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration
ASTM D 5453 : 2016 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 1319 : 2010 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2009 : REV A : EDT 5 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV C Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 2700 : 2016 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2015 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2699 : 2003 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2003 : REV B Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 1999 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 7320 : 2011 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 7320 : 2006 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 7320 : 2017 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 2699 : 2018 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2011 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2015 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4485 : 2006 : REV A Standard Specification for Performance of Engine Oils
ASTM D 4739 : 2011 : R2017 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4815 : 2009 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 4684 : 2002 : REV A Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 5453 : 2003 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 4175 : 2009 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4815 : 2015 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 4815 : 2004 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 4175 : 2016 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4815 : 1999 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 2700 : 2002 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2007 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2002 : REV A : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2008 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5293 : 2009 Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator
ASTM D 2699 : 2007 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2002 : REV A Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5191 : 2018 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 5453 : 2016 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 5191 : 2010 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4175 : 2000 : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 3237 : 2006 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 2700 : 2004 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4815 : 2013 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 4684 : 2007 : EDT 1 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 4052 : 1996 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
ASTM D 4739 : 2008 : EDT 1 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 5191 : 2002 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 2699 : 2004 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2015 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2013 : REV B Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4684 : 1999 : EDT 1 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 2700 : 2013 : REV B Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 7320 : 2009 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 7320 : 2013 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 5191 : 2019 Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 5293 : 1999 : REV A : EDT 1 Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35<sup>o</sup>C Using the Cold-Cranking Simulator
ASTM D 4485 : 2005 Standard Specification for Performance of Engine Oils
ASTM D 4684 : 2017 : REV A Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 5185 : 2009 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 2699 : 2001 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 7320 : 2008 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 2699 : 2006 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4815 : 2003 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography
ASTM D 5293 : 2017 : EDT 1 Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator
ASTM D 4485 : 2014 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5453 : 2019 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 2699 : 2015 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2002 Standard Specification for Performance of Engine Oils
ASTM D 4175 : 2017 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7320 : 2018 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 4485 : 2005 : EDT 1 Standard Specification for Performance of Engine Oils
ASTM D 2699 : 2002 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2009 : REV A : EDT 2 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2700 : 2017 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5185 : 2002 : EDT 1 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 7320 : 2017 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 3231 : 2007 Standard Test Method for Phosphorus in Gasoline
ASTM D 2700 : 2003 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2004 : REV A Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 3237 : 2017 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 5453 : 2019 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4175 : 2018 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2016 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 1319 : 2015 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 2699 : 2009 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2004 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5293 : 2004 Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator
ASTM D 2699 : 2006 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 3237 : 1997 Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy
ASTM D 5185 : 2002 : EDT 2 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 5191 : 2007 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 5293 : 2015 Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator
ASTM D 4684 : 2018 Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 4739 : 2011 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4739 : 2002 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 1319 : 2013 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 5293 : 2008 Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator
ASTM D 7320 : 2012 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 4052 : 2015 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 2700 : 2004 : EDT 1 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 3338 : 2005 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 3231 : 1989 Standard Test Method for Phosphorus in Gasoline
ASTM D 2700 : 2001 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4739 : 2006 : REV A Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 5191 : 2015 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 8047 : 2016 Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine
ASTM D 2699 : 2018 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 4175 : 2017 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7320 : 2010 : REV B Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 4815 : 2015 : REV A Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 5293 : 2010 Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator
ASTM D 7320 : 2016 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 7320 : 2010 : REV A Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine
ASTM D 4175 : 2019 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 3338 : 2008 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 3338 : 1995 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 2699 : 2013 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 3244 : 2007 : REV A Standard Practice for Utilization of Test Data to Determine Conformance with Specifications
ASTM D 2700 : 2019 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2009 Standard Specification for Performance of Engine Oils
ASTM D 3343 : 1995 : R2000 Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D 5452 : 2008 Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration
ASTM D 4175 : 2015 : REV B : EDT 1 Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 5191 : 2010 : REV B Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4485 : 2010 : REV A Standard Specification for Performance of Engine Oils
ASTM D 5453 : 2003 : REV A Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence
ASTM D 5293 : 2017 Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator
ASTM D 5293 : 2002 Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35°C Using the Cold-Cranking Simulator
ASTM D 4485 : 2011 Standard Specification for Performance of Engine Oils
ASTM D 2699 : 2010 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 5191 : 2013 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 3231 : 2011 Standard Test Method for Phosphorus in Gasoline
ASTM D 3237 : 2012 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 1319 : 2019 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 5191 : 2006 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4052 : 2018 Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
ASTM D 2699 : 2019 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2700 : 2004 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 1319 : 2002 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4175 : 2008 : REV B Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 2700 : 2008 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 5453 : 2008 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 4485 : 2007 : REV A Standard Specification for Performance of Engine Oils
ASTM D 5453 : 2000 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence

View more information
£92.22
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.