• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 111 : 2017 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus
Available format(s)

PDF

Language(s)

English

Published date

08-09-2017

CONTAINED IN VOL. 03.01, 2017 Describes the determination of Young's modulus, tangent modulus, and chord modulus of structural materials.

1.1This test method covers the determination of Young's modulus, tangent modulus, and chord modulus of structural materials, see Fig. 1. This test method is limited to materials in which and to temperatures and stresses at which creep is negligible compared to the strain produced immediately upon loading and to elastic behavior.

FIG. 1Stress-Strain Diagrams Showing Straight Lines Corresponding to (a) Young’s Modulus, (b) Tangent Modulus, and (c) Chord Modulus

1.2Because of experimental problems associated with the establishment of the origin of the stress-strain curve described in 8.1, the determination of the initial tangent modulus (that is, the slope of the stress-strain curve at the origin) and the secant modulus are outside the scope of this test method.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 28
DocumentType
Redline
Pages
11
PublisherName
American Society for Testing and Materials
Status
Current

API SPEC 11D1 : 2015 PACKERS AND BRIDGE PLUGS
SAE J 434 : 2017 AUTOMOTIVE DUCTILE (NODULAR) IRON CASTINGS
ASTM C 1298 : 1995 : R2007 Standard Guide for Design and Construction of Brick Liners for Industrial Chimneys
API TR 1PER15K-1 : 2013 PROTOCOL FOR VERIFICATION AND VALIDATION OF HIGH-PRESSURE HIGH-TEMPERATURE EQUIPMENT
14/30268531 DC : 0 BS EN ISO 6892-1 - METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE
ADA 14 : 82(R1998) DENTAL BASE METAL CASTING ALLOYS
ASTM E 2899 : 2015 : REDLINE Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending
ASTM D 3039/D3039M : 2017 : REDLINE Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
ASTM D 3410/D3410M : 2016 : REDLINE Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
ASTM E 1434 : 2000 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases
ASTM D 5379/D5379M : 2012 : REDLINE Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
ASTM E 447 : 1997 Test Methods for Compressive Strength of Laboratory Constructed Masonry Prisms (Withdrawn 1998)
ASTM D 5467/D5467M : 1997 : R2017 Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composite Materials Using a Sandwich Beam
ASTM C 747 : 2016 : REDLINE Standard Test Method for Moduli of Elasticity and Fundamental Frequencies of Carbon and Graphite Materials by Sonic Resonance
ASTM D 7078/D7078M : 2012 : REDLINE Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method
ASTM E 855 : 2008 Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading
EN 61788-18:2013 Superconductivity - Part 18: Mechanical properties measurement - Room temperature tensile test of Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
DOT/FAA/AR-MMPDS-01 : 20030131 METALLIC MATERIALS PROPERTIES DEVELOPMENT AND STANDARDIZATION (MMPDS)
BS EN 61788-19:2014 Superconductivity Mechanical properties measurement. Room temperature tensile test of reacted Nb<sub>3</sub>Sn composite superconductors
ASTM E 1434 : 2000 : R2013 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015)
ASTM E 606/E606M : 2012 : REDLINE Standard Test Method for Strain-Controlled Fatigue Testing
ASTM D 5467/D5467M : 1997 : R2010 Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam
PREN 6071 : 200P1 AEROSPACE SERIES - ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PLATE
API TR 17TR8 : 2018 HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES
ASTM C 1835 : 2016 Standard Classification for Fiber Reinforced Silicon Carbide-Silicon Carbide (SiC-SiC) Composite Structures
CEI EN 61788-18 : 2014 SUPERCONDUCTIVITY - PART 18: MECHANICAL PROPERTIES MEASUREMENT - ROOM TEMPERATURE TENSILE TEST OF AG- AND/OR AG ALLOY-SHEATHED BI-2223 AND BI-2212 COMPOSITE SUPERCONDUCTORS
ASTM D 5450/D5450M : 2016 : REDLINE Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM C 1836 : 2016 Standard Classification for Fiber Reinforced Carbon-Carbon Composite Structures
ASTM E 9 : 2009 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
ASTM C 1298 : 1995 Standard Guide for the Design and Construction of Brick Liners for Industrial Chimneys
ASTM D 3518/D3518M : 2013-09 TEST METHOD FOR IN-PLANE SHEAR RESPONSE OF POLYMER MATRIX COMPOSITE MATERIALS BY TENSILE TEST OF A +/-45 DEGREES LAMINATE
MIL-G-47032 Revision A:1990 GLASS, POTASH SODA BARIUM, LEAD FREE COMPRESSION SEALING
BS EN ISO 6892-1:2016 Metallic materials. Tensile testing Method of test at room temperature
CEI EN 61788-19 : 2014 SUPERCONDUCTIVITY - PART 19: MECHANICAL PROPERTIES MEASUREMENT - ROOM TEMPERATURE TENSILE TEST OF REACTED NB[3]SN COMPOSITE SUPERCONDUCTORS
API 5C5 RUSSIAN : 2017 PROCEDURES FOR TESTING CASING AND TUBING CONNECTIONS
ASTM C 1298 : 1995 : R2001 Standard Guide for the Design and Construction of Brick Liners for Industrial Chimneys
ASTM F 3122 : 2014 Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes
ASTM E 2714 : 2013 : REDLINE Standard Test Method for Creep-Fatigue Testing
ACI 530/530.1R : 2013 BUILDING CODE REQUIREMENTS AND SPECIFICATION FOR MASONRY STRUCTURES AND COMPANION COMMENTARIES
ASTM E 796 : 1994 Standard Test Method for Ductility Testing of Metallic Foil
ASTM E 132 : 2017 : REDLINE Standard Test Method for Poisson’s Ratio at Room Temperature
ASTM A 880 : 1995 Standard Practice for Criteria for Use in Evaluation of Testing Laboratories and Organizations for Examination and Inspection of Steel, Stainless Steel, and Related Alloys (Withdrawn 2004)
ASTM E 2368 : 2010 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
ASTM E 2368 : 2010 : R2017 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
ASTM C 1793 : 2015 Standard Guide for Development of Specifications for Fiber Reinforced Silicon Carbide-Silicon Carbide Composite Structures for Nuclear Applications
ASTM C 1783 : 2015 Standard Guide for Development of Specifications for Fiber Reinforced Carbon-Carbon Composite Structures for Nuclear Applications
ASTM E 796 : 1994 : R2000 Standard Test Method for Ductility Testing of Metallic Foil (Withdrawn 2009)
ASTM C 1298 : 1995 : R2013 Standard Guide for Design and Construction of Brick Liners for Industrial Chimneys
ASTM D 5467/D5467M : 1997 : R2004 Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam
MIL-Q-47057 Revision A:1990 QUARTZ, FUSED, OPTICAL GRADE
BS EN 61788-18:2013 Superconductivity Mechanical properties measurement. Room temperature tensile test of Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors
I.S. EN 61788-18:2013 SUPERCONDUCTIVITY - PART 18: MECHANICAL PROPERTIES MEASUREMENT - ROOM TEMPERATURE TENSILE TEST OF AG- AND/OR AG ALLOY-SHEATHED BI-2223 AND BI-2212 COMPOSITE SUPERCONDUCTORS
ASTM F 2789 : 201 Standard Guide for Mechanical and Functional Characterization of Nucleus Devices
ASTM E 1450 : 2016 : REDLINE Standard Test Method for Tension Testing of Structural Alloys in Liquid Helium
I.S. EN ISO 6892-1:2016 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
ASTM D 1566 : 2015 : REDLINE TERMINOLOGY RELATING TO RUBBER
ASTM E 1434 : 2000 : R2006 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases
IEC 61788-18:2013 Superconductivity - Part 18: Mechanical properties measurement - Room temperature tensile test of Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors
IEC 61788-19:2013 Superconductivity - Part 19: Mechanical properties measurement - Room temperature tensile test of reacted Nb3Sn composite superconductors
API 5C5 : 2017 PROCEDURES FOR TESTING CASING AND TUBING CONNECTIONS
I.S. EN 61788-19:2014 SUPERCONDUCTIVITY - PART 19: MECHANICAL PROPERTIES MEASUREMENT - ROOM TEMPERATURE TENSILE TEST OF REACTED NB[3]SN COMPOSITE SUPERCONDUCTORS
SAE J 2477 : 2018 AUTOMOTIVE AUSTEMPERED DUCTILE (NODULAR) IRON CASTINGS (ADI)
DIN EN ISO 6892-1:2017-02 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
ASTM E 855 : 2008 : R2013 Standard Test Methods for Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading
ASTM F 2789 : 2010 : R2015 Standard Guide for Mechanical and Functional Characterization of Nucleus Devices
ASTM D 5448/D5448M : 2016 : REDLINE Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM E 143 : 2013 : REDLINE Standard Test Method for Shear Modulus at Room Temperature
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
ASTM E 2207 : 2015 : REDLINE Standard Practice for Strain-Controlled Axial-Torsional Fatigue Testing with Thin-Walled Tubular Specimens
EN 61788-19:2014 Superconductivity - Part 19: Mechanical properties measurement - Room temperature tensile test of reacted Nb3Sn composite superconductors
ASME Y14.46 : 2017 PRODUCT DEFINITION FOR ADDITIVE MANUFACTURING

ASTM E 177 : 2014 : REDLINE Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E 83 : 2016 : REDLINE Standard Practice for Verification and Classification of Extensometer Systems
ASTM E 9 : 2009 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
ASTM E 8/E8M : 2016-09 TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.