• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 2813 : 2018

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Building Enclosure Commissioning

Available format(s)

Hardcopy , PDF

Superseded date

10-05-2024

Language(s)

English

Published date

29-11-2018

This practice is intended to serve as a concise, authoritative, and technically sound practice for Building Enclosure Commissioning (BECx) that establishes two levels of BECx:FundamentalandEnhanced(refer also to Section4).

1.1This practice is intended to serve as a concise, authoritative, and technically sound practice for Building Enclosure Commissioning (BECx) that establishes two levels of BECx: Fundamental and Enhanced (refer also to Section 4).

1.2The BECx process as defined in this practice includes the following phases and sub-phases:

1.2.1Pre-design,

1.2.2Design,

1.2.2.1Schematic Design,

1.2.2.2Design Development,

1.2.2.3Construction Documentation,

1.2.3Bidding and Negotiation Phase,

1.2.4Construction,

1.2.4.1Pre-Construction,

1.2.4.2Construction Administration, and

1.2.5Occupancy and Operations.

1.3This practice includes a mandatory OPR Development Guideline (Annex A1) and requires the development of an OPR for both Fundamental and Enhanced BECx that addresses, at a minimum, the performance attributes and metrics included in Annex A1 of this practice.

1.4This practice includes mandatory BECx Performance Testing Requirements (Annex A2) approved for use with this practice to evaluate the performance and durability of enclosure materials, components, systems, and assemblies.

1.5This practice mandates independent design review during the Design Phase of both Fundamental and Enhanced BECx.

1.6This practice recognizes that the OPR for exterior enclosure performance and environmental separation may exceed the baseline requirements of applicable building codes and standards and provides guidance for the development of an OPR based on the following attributes as defined in Annex A1 of this practice:

1.6.1Energy,

1.6.2Environment,

1.6.3Safety,

1.6.4Security,

1.6.5Durability,

1.6.6Sustainability, and

1.6.7Operation.

1.7The terms “building enclosure” and “enclosure” as they appear in this practice refer collectively to all materials, components, systems, and assemblies intended to provide shelter and environmental separation between interior and exterior, or between two or more environmentally distinct interior spaces in a building or structure.

1.8This practice establishes that the Building Enclosure Commissioning Provider (BECxP) refers specifically to the individual retained by the Owner to develop, manage, and be in responsible charge of the BECx process, including individual members and technical specialists that may comprise the BECx group (see 4.2).

1.9The role and responsibilities of the BECxP as defined by this practice are not intended to supersede or otherwise replace the contractual obligations reserved specifically for the parties responsible for the design and construction of a building or structure, nor the duties that may otherwise be assigned to those parties by applicable regulatory or statutory law.

1.10This practice is not intended to warrant or otherwise guarantee the as-built or in-service durability, or both, and performance of enclosure materials, components, systems, and assemblies.

1.11The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

1.12This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.13This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 06
DocumentType
Standard Practice
Pages
19
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 2947 : 2016 : REV A Standard Guide for Building Enclosure Commissioning
ASTM E 3223/E3223M : 2020 Standard Guide for Specifying and Testing Field-Constructed Exterior Building Wall System Mockups in New Construction

ASTM C 1651 : 2008 Standard Test Method for Measurement of Roll Wave Optical Distortion in Heat-Treated Flat Glass
ASTM F 1869 : 2009 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM E 1014 : 1984 : R1995 : EDT 1 Standard Guide for Measurement of Outdoor A-Weighted Sound Levels
ASTM E 2099 : 2000 : R2014 : EDT 1 Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems
ASTM E 492 : 2022 Standard Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using the Tapping Machine
ASTM C 1371 : 2004 : REV A : R2010 : EDT 1 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
ASTM F 1233 : 2008 Standard Test Method for Security Glazing Materials And Systems
ASTM E 2249 : 2019 Standard Test Method for Laboratory Measurement of Airborne Transmission Loss of Building Partitions and Elements Using Sound Intensity
ASTM E 1503 : 1997 Standard Test Method for Conducting Outdoor Sound Measurements Using a Digital Statistical Analysis System
ASTM C 1060 : 1990 : R2003 Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
ASTM E 1503 : 2014 Standard Test Method for Conducting Outdoor Sound Measurements Using a Digital Statistical Sound Analysis System
ASTM F 1869 : 1998 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM C 1601 : 2006 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM E 1105 : 2015 Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference
ASTM E 2947 : 2021 Standard Guide for Building Enclosure Commissioning
ASTM F 2420 : 2005 Standard Test Method for Determining Relative Humidity on the Surface of Concrete Floor Slabs Using Relative Humidity Probe Measurement and Insulated Hood
ASTM C 1153 : 1997 Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging
ASTM F 1233 : 1998 Standard Test Method for Security Glazing Materials And Systems
ASTM C 794 : 2018 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
ASTM E 2264 : 2023 Standard Practice for Determining the Effects of Temperature Cycling on Fenestration Products
ASTM F 1233 : 2008 : R2013 Standard Test Method for Security Glazing Materials And Systems
ASTM E 2353 : 2021 Standard Test Methods for Performance of Glazing in Permanent Railing Systems, Guards, and Balustrades
ASTM E 2178 : 2003 Standard Test Method for Air Permeance of Building Materials
ASTM F 2170 : 2018 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM F 2170 : 2016 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM E 1186 : 2003 Standard Practices for Air Leakage Site Detection in Building Envelopes and Air Barrier Systems
ASTM E 1050 : 1998 Standard Test Method for Impedance and Absorption of Acoustical Materials Using a Tube, Two Microphones, and a Digital Frequency Analysis System
ASTM E 2947 : 2015 Standard Guide for Building Enclosure Commissioning
ASTM E 2947 : 2016 : REV A Standard Guide for Building Enclosure Commissioning
ASTM C 1549 : 2016 Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
ASTM D 4541 : 2009 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 1886 : 2004 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM E 2179 : 2001 Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
ASTM D 2203 : 2001 : R2023 Standard Test Method for Staining from Sealants
ASTM C 1246 : 2000 : R2012 Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure
ASTM E 2357 : 2011 Standard Test Method for Determining Air Leakage of Air Barrier Assemblies
ASTM E 1996 : 2012 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 1186 : 1998 Standard Practices for Air Leakage Site Detection in Building Envelopes and Air Retarder Systems
ASTM C 1601 : 2022 : REV A Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM C 1279 : 1994 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM E 2649 : 2009 Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy
ASTM E 1105 : 2000 Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform or Cyclic Static Air Pressure Difference
ASTM C 1087 : 2023 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM E 1996 : 2012 : REV A Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM F 2170 : 2016 : REV B Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM E 2353 : 2014 Standard Test Methods for Performance of Glazing in Permanent Railing Systems, Guards, and Balustrades
ASTM E 1886 : 2013 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM E 1105 : 2000 : R2008 Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference
ASTM E 1050 : 2008 Standard Test Method for Impedance and Absorption of Acoustical Materials Using A Tube, Two Microphones and A Digital Frequency Analysis System
ASTM E 1186 : 2003 : R2009 Standard Practices for Air Leakage Site Detection in Building Envelopes and Air Barrier Systems
ASTM F 1869 : 2010 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM E 795 : 2016 Standard Practices for Mounting Test Specimens During Sound Absorption Tests
ASTM E 2353 : 2016 Standard Test Methods for Performance of Glazing in Permanent Railing Systems, Guards, and Balustrades
ASTM C 1294 : 2015 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM C 522 : 2003 : R2022 Standard Test Method for Airflow Resistance of Acoustical Materials
ASTM C 1279 : 2000 : EDT 1 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM E 1827 : 1996 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
ASTM F 1869 : 2016 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM C 1601 : 2008 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM C 1279 : 2000 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM F 1869 : 2003 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM C 1060 : 2011 : REV A Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
ASTM E 2268 : 2004 : R2023 Standard Test Method for Water Penetration of Exterior Windows, Skylights, and Doors by Rapid Pulsed Air Pressure Difference
ASTM F 1869 : 2004 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM C 423 : 2017 Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
ASTM E 1007 : 2019 Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM E 336 : 2023 Standard Test Method for Measurement of Airborne Sound Attenuation between Rooms in Buildings
ASTM C 1087 : 2000 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM E 1980 : 1998 : EDT 1 Standard Practice for Calculating Solar Reflectance Index of Horizontal and Low-Sloped Opaque Surfaces
ASTM D 2203 : 2001 : R2007 Standard Test Method for Staining from Sealants
ASTM C 1294 : 2007 : EDT 1 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 2179 : 2003 : EDT 1 Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
ASTM E 1996 : 2002 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
ASTM E 492 : 2009 : R2016 : EDT 1 Standard Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using the Tapping Machine
ASTM E 1425 : 2014 Standard Practice for Determining the Acoustical Performance of Windows, Doors, Skylight, and Glazed Wall Systems
ASTM F 1233 : 2021 Standard Test Method for Security Glazing Materials And Systems
ASTM E 2353 : 2004 Standard Test Methods for Performance of Glass in Permanent Glass Railing Systems, Guards, and Balustrades
ASTM E 2359/E2359M : 2013 : R2018 Standard Test Method for Field Pull Testing of an In-Place Exterior Insulation and Finish System Clad Wall Assembly
ASTM E 596 : 2022 Standard Test Method for Laboratory Measurement of Noise Reduction of Sound-Isolating Enclosures
ASTM C 1294 : 2007 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM D 5957 : 1998 : R2005 Standard Guide for Flood Testing Horizontal Waterproofing Installations
ASTM E 1827 : 2011 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
ASTM E 2319 : 2004 : R2019 Standard Test Method for Determining Air Flow Through the Face and Sides of Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen
ASTM C 423 : 2022 Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
ASTM C 522 : 2003 : R2016 Standard Test Method for Airflow Resistance of Acoustical Materials
ASTM C 1371 : 1998 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
ASTM D 4541 : 2009 : EDT 1 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 2099 : 2000 Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems
ASTM E 2264 :2005 Standard Practice for Determining the Effects of Temperature Cycling on Fenestration Products
ASTM C 1601 : 2011 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM E 2249 : 2002 : R2016 Standard Test Method for Laboratory Measurement of Airborne Transmission Loss of Building Partitions and Elements Using Sound Intensity
ASTM E 1503 : 1997 : R2004 Standard Test Method for Conducting Outdoor Sound Measurements Using a Digital Statistical Analysis System
ASTM C 1601 : 2005 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM E 2264 : 2005 : R2013 Standard Practice for Determining the Effects of Temperature Cycling on Fenestration Products
ASTM E 1996 : 2023 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1279 : 2013 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM C 1522 : 2002 Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes
ASTM E 1050 : 2007 Standard Test Method for Impedance and Absorption of Acoustical Materials Using A Tube, Two Microphones and A Digital Frequency Analysis System
ASTM C 1652/C1652M : 2014 Standard Test Method for Measuring Optical Distortion in Flat Glass Products Using Digital Photography of Grids
ASTM E 997 : 2015 : R2021 Standard Test Method for Evaluating Glass Breakage Probability Under the Influence of Uniform Static Loads by Proof Load Testing
ASTM F 2170 : 2016 : REV A Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM E 1996 : 2006 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 2178 : 2013 Standard Test Method for Air Permeance of Building Materials
ASTM E 1425 : 2007 Standard Practice for Determining the Acoustical Performance of Windows, Doors, Skylight, and Glazed Wall Systems
ASTM C 1279 : 2023 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM E 1105 : 2015 : R2023 Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference
ASTM E 2249 : 2002 : R2008 Standard Test Method for Laboratory Measurement of Airborne Transmission Loss of Building Partitions and Elements Using Sound Intensity
ASTM E 1050 : 2010 Standard Test Method for Impedance and Absorption of Acoustical Materials Using A Tube, Two Microphones and A Digital Frequency Analysis System
ASTM E 1996 : 2005 : REV A Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 2264 : 2005 : R2021 Standard Practice for Determining the Effects of Temperature Cycling on Fenestration Products
ASTM E 1996 : 2004 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 1014 : 1984 : R2000 Standard Guide for Measurement of Outdoor A-Weighted Sound Levels
ASTM E 2099 : 2000 : R2007 Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems
ASTM E 2357 : 2018 Standard Test Method for Determining Air Leakage Rate of Air Barrier Assemblies
ASTM E 336 : 2020 Standard Test Method for Measurement of Airborne Sound Attenuation between Rooms in Buildings
ASTM E 1886 : 2005 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM C 1153 : 2010 Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging
ASTM C 1258 : 2021 : REV A Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
ASTM E 2357 : 2017 Standard Test Method for Determining Air Leakage of Air Barrier Assemblies
ASTM E 2179 : 2003 : EDT 2 Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
ASTM E 1980 : 2001 Standard Practice for Calculating Solar Reflectance Index of Horizontal and Low-Sloped Opaque Surfaces (Withdrawn 2010)
ASTM D 4541 : 2002 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 488/E488M : 2022 Standard Test Methods for Strength of Anchors in Concrete Elements
ASTM E 2179 : 2003 : R2009 Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
ASTM E 2268 : 2004 Standard Test Method for Water Penetration of Exterior Windows, Skylights, and Doors by Rapid Pulsed Air Pressure Difference
ASTM E 2178 : 2021 : REV A Standard Test Method for Determining Air Leakage Rate and Calculation of Air Permeance of Building Materials
ASTM E 330/E330M : 2014 : R2021 Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference
ASTM E 2570/E2570M : 2007 : R2019 Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage
ASTM C 1549 : 2002 Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
ASTM E 2268 : 2004 : R2011 Standard Test Method for Water Penetration of Exterior Windows, Skylights, and Doors by Rapid Pulsed Air Pressure Difference
ASTM F 2420 : 2005 : R2011 Standard Test Method for Determining Relative Humidity on the Surface of Concrete Floor Slabs Using Relative Humidity Probe Measurement and Insulated Hood (Withdrawn 2014)
ASTM D 2203 : 2001 : R2018 Standard Test Method for Staining from Sealants
ASTM E 2319 : 2022 Standard Test Method for Determining Air Flow Through the Face and Sides of Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen
ASTM E 1996 : 2008 : EDT 1 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM F 2170 : 2002 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using <bdit> in situ</bdit> Probes
ASTM C 1522 : 2005 : R2013 Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes
ASTM E 1007 : 2011 : EDT 1 Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM E 1007 : 2013 : REV A Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM C 732 : 2017 : R2022 Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants
ASTM D 2203 : 1993 Standard Test Method for Staining from Sealants
ASTM E 1050 : 2019 Standard Test Method for Impedance and Absorption of Acoustical Materials Using a Tube, Two Microphones and a Digital Frequency Analysis System
ASTM C 1153 : 2010 : R2015 Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging
ASTM C 1246 : 2017 Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure
ASTM E 2099 : 2023 Standard Practice for Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems
ASTM D 4541 : 2017 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 1996 : 2009 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1246 : 2017 : R2022 Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure
ASTM C 1294 : 1995 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM D 4541 : 2022 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 1996 : 2001 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
ASTM C 1652/C1652M : 2021 Standard Test Method for Measuring Optical Distortion in Flat Glass Products Using Digital Photography of Grids
ASTM C 1060 : 1990 : R1997 : EDT 1 Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
ASTM C 794 : 2018 : R2022 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
ASTM E 1503 : 2022 Standard Test Method for Conducting Outdoor Sound Measurements Using a Statistical Sound Analysis System
ASTM E 2649 : 2012 Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy
ASTM F 1869 : 2016 : REV A Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM D 5957 : 1998 : R2013 Standard Guide for Flood Testing Horizontal Waterproofing Installations
ASTM F 2170 : 2009 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using <bdit> in situ</bdit> Probes
ASTM E 1996 : 2014 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1601 : 2020 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM E 2179 : 2003 Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
ASTM D 2203 : 2001 : R2011 Standard Test Method for Staining from Sealants
ASTM C 1371 : 2015 : R2022 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
ASTM E 1996 : 2014 : REV A Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 423 : 2023 Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
ASTM E 2179 : 2021 Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
ASTM E 1014 : 2012 : R2021 Standard Guide for Measurement of Outdoor A-Weighted Sound Levels
ASTM C 1258 : 1994 Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
ASTM E 1050 : 2012 Standard Test Method for Impedance and Absorption of Acoustical Materials Using a Tube, Two Microphones and a Digital Frequency Analysis System
ASTM E 1980 : 2011 : R2019 Standard Practice for Calculating Solar Reflectance Index of Horizontal and Low-Sloped Opaque Surfaces
ASTM E 1886 : 2013 : REV A Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM F 2170 : 2011 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM C 1087 : 2016 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1601 : 2014 : REV A Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM E 1007 : 1997 Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM E 1996 : 2005 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1371 : 2004 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
ASTM C 732 : 2017 Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants
ASTM D 5957 : 1998 : R2021 Standard Guide for Flood Testing Horizontal Waterproofing Installations
ASTM F 1233 : 2008 : R2019 Standard Test Method for Security Glazing Materials And Systems
ASTM E 1827 : 2011 : R2017 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
ASTM E 2319 : 2004 Standard Test Method for Determining Air Flow Through the Face and Sides of Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen
ASTM E 2353 : 2006 Standard Test Methods for Performance of Glass in Permanent Glass Railing Systems, Guards, and Balustrades
ASTM E 1996 : 2017 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 2179 : 2003 : R2016 Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
ASTM C 1279 : 2013 : R2019 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM F 1869 : 2011 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 2170 : 2017 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM C 1060 : 2011 Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
ASTM C 1087 : 2000 : R2011 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1258 : 2008 : R2013 Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
ASTM E 2947 : 2021 : REV A Standard Guide for Building Enclosure Commissioning
ASTM C 1258 : 2019 Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
ASTM E 1996 : 2020 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 331 : 2000 : R2023 Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference
ASTM F 1869 : 2022 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM C 1601 : 2014 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM E 90 : 2023 Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
ASTM E 2359/E2359M : 2013 : R2023 Standard Test Method for Field Pull Testing of an In-Place Exterior Insulation and Finish System Clad Wall Assembly
ASTM E 2947 : 2016 Standard Guide for Building Enclosure Commissioning
ASTM E 795 : 2023 Standard Practices for Mounting Test Specimens During Sound Absorption Tests
ASTM D 5957 : 1998 Standard Guide for Flood Testing Horizontal Waterproofing Installations
ASTM C 1549 : 2016 : R2022 Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
ASTM C 1601 : 2009 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM E 1186 : 2017 Standard Practices for Air Leakage Site Detection in Building Envelopes and Air Barrier Systems
ASTM F 1869 : 2023 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM E 1827 : 2022 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
ASTM E 1425 : 1991 : R1999 Standard Practice for Determining the Acoustical Performance of Exterior Windows and Doors
ASTM E 1996 : 2008 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 1425 : 2014 : R2023 Standard Practice for Determining the Acoustical Performance of Windows, Doors, Skylight, and Glazed Wall Systems
ASTM E 1886 : 2019 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM C 1294 : 2001 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 2649 : 2020 Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units Using Spark Emission Spectroscopy
ASTM E 783 : 2002 : R2018 Standard Test Method for Field Measurement of Air Leakage Through Installed Exterior Windows and Doors
ASTM E 1007 : 2021 Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM C 1153 : 2023 Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging
ASTM E 1827 : 1996 : R2002 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
ASTM E 1007 : 2013 : REV B Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM E 1996 : 2005 : REV B Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1294 : 2007 : R2011 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 1996 : 2003 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
ASTM C 1279 : 2005 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM F 2170 : 2019 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM C 510 : 2016 Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
ASTM E 1007 : 2014 Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM C 1258 : 2021 Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
ASTM C 1601 : 2022 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM C 1371 : 2004 : REV A Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
ASTM E 1007 : 2004 : EDT 1 Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM E 1014 : 2008 Standard Guide for Measurement of Outdoor A-Weighted Sound Levels
ASTM E 2178 : 2021 Standard Test Method for Determining Air Leakage Rate and Calculation of Air Permeance of Building Materials
ASTM E 1503 : 2012 Standard Test Method for Conducting Outdoor Sound Measurements Using a Digital Statistical Sound Analysis System
ASTM F 2170 : 2019 : REV A Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM C 1549 : 2009 : R2014 Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
ASTM C 1651 : 2011 Standard Test Method for Measurement of Roll Wave Optical Distortion in Heat-Treated Flat Glass
ASTM E 488/E488M : 2018 Standard Test Methods for Strength of Anchors in Concrete Elements
ASTM E 2319 : 2004 : R2011 Standard Test Method for Determining Air Flow Through the Face and Sides of Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen
ASTM E 2947 : 2014 Standard Guide for Building Enclosure Commissioning
ASTM E 331 : 2000 : R2016 Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference
ASTM E 997 : 2015 Standard Test Method for Evaluating Glass Breakage Probability Under the Influence of Uniform Static Loads by Proof Load Testing
ASTM C 1060 : 2011 : REV A : R2015 Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
ASTM E 1980 : 2011 Standard Practice for Calculating Solar Reflectance Index of Horizontal and Low-Sloped Opaque Surfaces
ASTM C 510 : 2016 : R2022 Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
ASTM C 1549 : 2004 Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
ASTM E 2178 : 2011 Standard Test Method for Air Permeance of Building Materials
ASTM E 1007 : 2016 Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
ASTM C 1651 : 2011 : R2018 Standard Test Method for Measurement of Roll Wave Optical Distortion in Heat-Treated Flat Glass
ASTM C 1246 : 2000 Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure
ASTM C 1246 : 2000 : R2006 Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure
ASTM D 4541 : 1995 : EDT 1 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 90 : 2009 : R2016 Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
ASTM C 1087 : 2000 : R2006 : EDT 1 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM E 1886 : 2002 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Storm Shutters Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM E 1886 : 2004 : REV A Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM C 1087 : 2000 : R2006 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1601 : 2004 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM C 1258 : 2008 Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
ASTM C 1522 : 2005 : R2021 Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes
ASTM E 2178 : 2001 Standard Test Method for Air Permeance of Building Materials
ASTM E 2357 : 2023 Standard Test Method for Determining Air Leakage Rate of Air Barrier Assemblies
ASTM E 1503 : 2005 Standard Test Method for Conducting Outdoor Sound Measurements Using a Digital Statistical Analysis System
ASTM E 2249 : 2002 Standard Test Method for Laboratory Measurement of Airborne Transmission Loss of Building Partitions and Elements Using Sound Intensity
ASTM D 2203 : 2001 Standard Test Method for Staining from Sealants
ASTM E 2268 : 2004 : R2016 Standard Test Method for Water Penetration of Exterior Windows, Skylights, and Doors by Rapid Pulsed Air Pressure Difference
ASTM E 2357 : 2023 : REV A Standard Test Method for Determining Air Leakage Rate of Air Barrier Assemblies
ASTM E 1827 : 1996 : R2007 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
ASTM E 596 : 1996 : R2016 Standard Test Method for Laboratory Measurement of Noise Reduction of Sound-Isolating Enclosures
ASTM C 1371 : 2015 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
ASTM E 1886 : 1997 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Storm Shutters Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM E 2357 : 2024 Standard Test Method for Determining Air Leakage Rate of Air Barrier Assemblies
ASTM E 2357 : 2005 Standard Test Method for Determining Air Leakage of Air Barrier Assemblies
ASTM C 1279 : 2009 Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
ASTM E 330/E330M : 2014 Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference
ASTM C 1549 : 2009 Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
ASTM C 1522 : 2005 Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes
ASTM E 1014 : 2012 Standard Guide for Measurement of Outdoor A-Weighted Sound Levels
ASTM E 1503 : 2006 Standard Test Method for Conducting Outdoor Sound Measurements Using a Digital Statistical Sound Analysis System
ASTM E 1186 : 2022 Standard Practices for Air Leakage Site Detection in Building Envelopes and Air Barrier Systems
ASTM E 997 : 1984 : R1992 : EDT 1 Standard Test Method for Structural Performance of Glass in Exterior Windows, Curtain Walls, and Doors Under the Influence of Uniform Static Loads by Destructive Methods
ASTM C 1601 : 2010 Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
ASTM C 1060 : 2023 Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings

View more information
£70.87
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.