• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 537 : 2012 : REDLINE

Current

Current

The latest, up-to-date edition.

Standard Test Method for The Thermal Stability of Chemicals by Differential Scanning Calorimetry

Available format(s)

PDF

Language(s)

English

Published date

01-12-2012

CONTAINED IN VOL. 14.02, 2016 Specifies the ascertainment of the presence of enthalpic changes in a test specimen, using minimum quantities of material, approximates the temperature at which these enthalpic changes occur and determines their enthalpies (heats) using differential scanning calorimetry or pressure differential scanning calorimetry.

Committee
E 27
DocumentType
Redline
Pages
8
PublisherName
American Society for Testing and Materials
Status
Current

1.1This test method describes the ascertainment of the presence of enthalpic changes in a test specimen, using minimum quantities of material, approximates the temperature at which these enthalpic changes occur and determines their enthalpies (heats) using differential scanning calorimetry or pressure differential scanning calorimetry.

1.2This test method may be performed on solids, liquids, or slurries.

1.3This test method may be performed in an inert or a reactive atmosphere with an absolute pressure range from 100 Pa through 7 MPa and over a temperature range from 300 to 800 K (27 to 527°C).

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5There is no ISO standard equivalent to this test method.

1.6This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific safety precautions are given in Section 8.

NFPA 704 : 2017 STANDARD SYSTEM FOR THE IDENTIFICATION OF THE HAZARDS OF MATERIALS FOR EMERGENCY RESPONSE
MIL-PRF-46197 Revision A:1997 LAMINATE: HIGH-STRENGTH GLASS, FABRIC-REINFORCED, POLYESTER RESIN PREIMPREGNATED
ASTM E 2046 : 2014 : REDLINE Standard Test Method for Reaction Induction Time by Thermal Analysis
ASTM E 1981 : 1998 : R2004 Standard Guide for Assessing the Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry
ASTM E 1231 : 2015 : REDLINE Standard Practice for Calculation of Hazard Potential Figures of Merit for Thermally Unstable Materials
ASTM E 1981 : 1998 : R2012 : EDT 2 Standard Guide for Assessing Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry
ASTM E 2890 : 2012 : EDT 1 Standard Test Method for Kinetic Parameters for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger Method
NFPA FIRE PROT GUIDE ON HAZARDOUS MAT : 2010 FIRE PROTECTION GUIDE TO HAZARDOUS MATERIALS
ASTM E 487 : 2014 : REDLINE Standard Test Method for Constant-Temperature Stability of Chemical Materials
SAE J 3042 : 2015 MEASURING PROPERTIES OF LI-BATTERY ELECTROLYTE
ASTM E 2550 : 2017 : REDLINE Standard Test Method for Thermal Stability by Thermogravimetry
ASTM E 2160 : 2004 Standard Test Method for Heat of Reaction of Thermally Reactive Materials by Differential Scanning Calorimetry
ASTM E 1445 : 2008 Standard Terminology Relating to Hazard Potential of Chemicals
ASTM E 1445 : 2008 : R2015 Standard Terminology Relating to Hazard Potential of Chemicals
ASTM E 2012 : 2006 Standard Guide for the Preparation of a Binary Chemical Compatibility Chart
MIL-DTL-82965 Revision B:2001 Propellant, gun, High Energy Nitramine
MIL-DTL-32040 Base Document:1999 Propellant, Gun, High Energy Nitramine
ASTM E 1981 : 1998 Standard Guide for Assessing the Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry
ASTM E 2890 : 2012 Standard Test Method for Kinetic Parameters for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger Method
ASTM E 1981 : 1998 : R2012 : EDT 1 Standard Guide for Assessing Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry
ASTM E 2160 : 2004 : R2012 Standard Test Method for Heat of Reaction of Thermally Reactive Materials by Differential Scanning Calorimetry
ASTM E 1232 : 2007 : R2013 Standard Test Method for Temperature Limit of Flammability of Chemicals
ASTM E 1232 : 2007 Standard Test Method for Temperature Limit of Flammability of Chemicals
ASTM E 1591 : 2013 Standard Guide for Obtaining Data for Fire Growth Models
MIL L 46197 : (1) LAMINATE: HIGH STRENGTH GLASS, FABRIC REINFORCED, POLYESTER RESIN PREIMPREGNATED
MIL-I-24092 Revision D:1993 INSULATING VARNISHES AND SOLVENTLESS RESINS FOR APPLICATION BY THE DIP PROCESS
SAE J 3021 : 2014 RECOMMENDED PRACTICE FOR DETERMINING MATERIAL PROPERTIES OF LI-BATTERY CATHODE ACTIVE MATERIALS
ASTM E 2041 : 2013 : EDT 1 Standard Test Method for Estimating Kinetic Parameters by Differential Scanning Calorimeter Using the Borchardt and Daniels Method
ASTM E 1232 : 2007 : R2019 Standard Test Method for Temperature Limit of Flammability of Chemicals
ASTM E 2012 : 2006 : R2012 Standard Guide for the Preparation of a Binary Chemical Compatibility Chart

ASTM E 473 : 2016-05 TERMINOLOGY RELATING TO THERMAL ANALYSIS AND RHEOLOGY

View more information
£64.04
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.