• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 1667 : 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
Available format(s)

Hardcopy , PDF

Superseded date

09-10-2018

Language(s)

English

Published date

01-09-2015

1.1This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.

Note 1:Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.

(A)All dimensions given in inches.
(A)All dimensions are given in inches.
(A)All dimension are given in inches.
(A)All dimensions are given in inches.
(A)All dimensions are given in inches.
(B)Dashes (—) indicate that the fastener size is not a standard size.

 Editorially corrected in March 2012.

(A)All dimensions are given in inches.
(B)Dashes (—) indicate that the fastener size is not a standard size.

L = length, in.,
H = head diameter, in.,
TL = length of threaded shank, in.,
max = maximum acceptable value (not subject to tolerances),
min = minimum acceptable value (not subject to tolerances),
D = shank diameter, in.,
T1 = crest diameter, in., and
P = pitch, or spacing of threads, in.
(A)All dimensions are given in inches.
(B)Root diameter is a calculated value and is not specified as a dimension to be measured.

L = length, in.,
H = head diameter, in.,
TL = length of threaded shank, in.,
max = maximum acceptable value (not subject to tolerances),
min = minimum acceptable value (not subject to tolerances),
D = shank diameter, in.,
T1 = crest diameter, in., and
P = pitch, or spacing of threads, in.
(A)All dimensions are given in inches.
(B)Nails shall comply with the supplementary requirements of S1 and Table S1.1.
(C)Nails identified as “F1667 NLRSRS” must meet all applicable requirements of F1667 for the specified roof sheathing ring shank nail.
(D)Individual rings shall be approximately frustrums, circular in transverse cross section, axially symmetric, and formed on the nail axis such that the minor diameter is closer to the nail point and the major diameter is closer to the nail head. The thread shall be continuous over the minimum thread length, TLmin.
(A)All dimensions are given in inches.

Dimensions and Tolerances for Gages of Flat Top Crown Staples

10 Gage

12 Gage

14 Gage

15 Gage

16 Gage

18 Gage

T

W

T

W

T

W

T

W

T

W

T

W

Nominal

.1250

.1400

.0935

.1120

.0735

.0855

.0673

.073

.0563

.064

.038

.050

Maximum

.1290

.1440

.0975

.1160

.0775

.0895

.0731

.076

.0626

.068

.0415

.0532

Minimum

.1210

.1360

.0895

.1080

.0695

.0815

.0615

.070

.0500

.060

.0345

.0468

Tolerance

±

.0040

.0040

.0040

.0040

.0040

.0040

.0058

.003

.0063

.004

.0035

.0032

(A)All dimensions are given in inches.

1.2Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.

1.3The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.4Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 16
DocumentType
Standard
Pages
47
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 228/D228M : 2019 Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing
ASTM D 6255/D6255M : 2018 Standard Specification for Steel or Aluminum Slotted Angle Crates
ASTM D 7672 : 2014 : EDT 1 Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies
ASTM D 7349/D7349M : 2015 Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal around Fasteners
ASTM F 1575 : 2017 Standard Test Method for Determining Bending Yield Moment of Nails
ASTM D 6254/D6254M : 2013 Standard Specification for Wirebound Pallet-Type Wood Boxes
ASTM D 6251/D6251M : 2011 Standard Specification for Wood-Cleated Panelboard Shipping Boxes
ASTM F 547 : 2017 Standard Terminology of Nails for Use with Wood and Wood-Base Materials
ASTM D 3462/D3462M : 2019 Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
ASTM D 7374 : 2008 : R2015 Standard Practice for Evaluating Elevated Temperature Performance of Adhesives Used in End-Jointed Lumber
ASTM D 7478/D7478M : 2011 : R2017 Standard Specification for Heavy Duty Sheathed Wood Crates
ASTM D 6573/D6573M : 2013 Standard Specification for General Purpose Wirebound Shipping Boxes
ASTM D 6880/D6880M : 2011 Standard Specification for Wood Boxes
ASTM B 900 : 2016 Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies
ASTM F 537 : 2001 : R2014 Standard Specification for Design, Fabrication, and Installation of Fences Constructed of Wood and Related Materials
ASTM D 6039/D6039M : 2018 Standard Specification for Open and Covered Wood Crates
ASTM D 1185 : 1998 : REV A : R2017 Standard Test Methods for Pallets and Related Structures Employed in Materials Handling and Shipping
ASTM D 6256/D6256M : 2016 Standard Specification for Wood-Cleated Shipping Boxes with Skidded, Load-Bearing Bases
ASTM D 7989 : 2018 Standard Practice for Demonstrating Equivalent In-Plane Lateral Seismic Performance to Wood-Frame Shear Walls Sheathed with Wood Structural Panels
ASTM B 660 : 2015 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
ASTM F 3359 : 2018 Standard Test Method for Determining Bending Yield Moment of Staples
ASTM C 1861 : 2018 Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster
ASTM D 7470 : 2008 : R2015 Standard Practice for Evaluating Elevated Temperature Performance of End-Jointed Lumber Studs
ASTM E 2266 : 2011 Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion

View more information
£97.67
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.