BS ISO 16151 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CORROSION OF METALS AND ALLOYS - ACCELERATED CYCLIC TESTS WITH EXPOSURE TO ACIDIFIED SALT SPRAY, "DRY" AND "WET" CONDITIONS
Hardcopy , PDF
English
01-01-2005
30-06-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Test solution
3.1 Method A
3.1.1 Preparation of acidic 5 % sodium
chloride solution
3.2 Method B
3.2.1 Preparation of the mixed salt solution
3.2.2 Preparation of the acidic solution
3.2.3 Preparation of the acidified-salt solution
4 Apparatus
4.1 Exposure cabinet
4.2 Humidity and temperature control
4.3 Spraying device
4.4 Air saturator
4.5 Collecting devices
4.6 Air dryer
4.7 Exhaust system
4.8 Drain system
5 Test specimens
6 Arrangement of the test specimens
7 Operating conditions
8 Continuity of tests
9 Duration of tests
10 Treatment of specimens after test
11 Evaluation of results
12 Test report
Annex A (informative) Relationship between amount of
acidic stock solution added to mixed salt solution
and pH of the resulting acidified-salt solution
Annex B (informative) Typical apparatus for accelerated
cyclic tests with exposure to acidified salt spray,
"dry" and "wet" conditions
Annex C (informative) Method of evaluation of the
corrosivity of the chamber
Bibliography
Describes two accelerated corrosion-test procedures, Methods A and B, for the comparative evaluation of metallic materials with or without permanent corrosion protection or temporary corrosion protection in outdoor salt/acid rain environments. Also specifies the apparatus used.
| Committee |
ISE/NFE/8
|
| DevelopmentNote |
Supersedes 03/115104 DC (01/2006) Renumbered and Superseded by BS EN ISO 16151. (06/2008)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 16151:2005 | Identical |
| ISO 8993:2010 | Anodizing of aluminium and its alloys — Rating system for the evaluation of pitting corrosion — Chart method |
| ISO 11130:2010 | Corrosion of metals and alloys — Alternate immersion test in salt solution |
| JASO M 609 : 1991 | MATERIAL AND SURFACE TREATMENT - CORROSION TEST METHOD FOR AUTOMOTIVE MATERIALS |
| ISO 3574:2012 | Cold-reduced carbon steel sheet of commercial and drawing qualities |
| ISO 4628-4:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 4: Assessment of degree of cracking |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 4628-5:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 5: Assessment of degree of flaking |
| ISO 4628-1:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 1: General introduction and designation system |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 8407:2009 | Corrosion of metals and alloys — Removal of corrosion products from corrosion test specimens |
| JASO M 610 : 1992 | MATERIAL AND SURFACE TREATMENT - COSMETIC CORROSION TEST METHOD FOR AUTOMOTIVE PARTS |
| ISO 10289:1999 | Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates — Rating of test specimens and manufactured articles subjected to corrosion tests |
| ISO 4628-2:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 2: Assessment of degree of blistering |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.