• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

CEN/TR 16912:2016

Current
Current

The latest, up-to-date edition.

Guidelines for a procedure to support the European standardization of cements
Published date

25-05-2016

European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Procedure of application and standardization
  of a new cement
5 Assessment of fitness for use
6 Patents and other intellectual property rights
  (IPR) relevant for the standardization of the
  new cement
Bibliography

This CEN Technical Report provides guidance for the procedure to be followed in order to support the European standardization of new cements that are not covered by an existing European Standard. The term 'new cement' has been used in this document to describe its primary focus, however, this same guideline procedure may be used for other products to be standardized by CEN/TC 51.

Committee
CEN/TC 51
DocumentType
Technical Report
PublisherName
Comite Europeen de Normalisation
Status
Current

Standards Relationship
PD CEN/TR 16912:2016 Identical
S.R. CEN/TR 16912:2016 Identical
NEN NPR CEN/TR 16912 : 2016 Identical
SIS-CEN/TR 16912:2021 Identical

EN 13282-1:2013 Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
CEN/TR 15177:2006 Testing the freeze-thaw resistance of concrete - Internal structural damage
EN 196-7:2007 Methods of testing cement - Part 7: Methods of taking and preparing samples of cement
CEN/TS 16516:2013 Construction products - Assessment of release of dangerous substances - Determination of emissions into indoor air
EN 196-2:2013 Method of testing cement - Part 2: Chemical analysis of cement
EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements
CEN/TS 16637-2:2014 Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test
EN 459-2:2010 Building lime - Part 2: Test methods
EN 12350-2:2009 Testing fresh concrete - Part 2: Slump-test
EN 196-5:2011 Methods of testing cement - Part 5: Pozzolanicity test for pozzolanic cement
EN 197-2:2014 Cement - Part 2: Conformity evaluation
CEN/TR 196-4:2007 Methods of testing cement - Part 4: Quantitative determination of constituents
EN 459-1:2015 BUILDING LIME - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
EN 15743:2010+A1:2015 Supersulfated cement - Composition, specifications and conformity criteria
ISO 9286:1997 Abrasive grains and crude Chemical analysis of silicon carbide
EN 12390-11:2015 Testing hardened concrete - Part 11: Determination of the chloride resistance of concrete, unidirectional diffusion
EN 933-9:2009+A1:2013 Tests for geometrical properties of aggregates - Part 9: Assessment of fines - Methylene blue test
EN 14647:2005/AC:2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
CEN/TR 15678:2008 Concrete - Release of regulated dangerous substances into soil, groundwater and surface water - Test method for new or unapproved constituents of concrete and for production concretes
EN 196-10:2016 Methods of testing cement - Part 10: Determination of the water-soluble chromium (VI) content of cement
EN 14216:2015 Cement - Composition, specifications and conformity criteria for very low heat special cements
EN 13639:2017 Determination of total organic carbon in limestone
EN 413-1:2011 Masonry cement - Part 1: Composition, specifications and conformity criteria
EN 45020:2006 Standardization and related activities - General vocabulary (ISO/IEC Guide 2:2004)
EN 13282-2:2015 Hydraulic road binders - Part 2: Normal hardening hydraulic road binders - Composition, specifications and conformity criteria
CEN/TS 12390-9:2016 Testing hardened concrete - Part 9: Freeze-thaw resistance with de-icing salts - Scaling
EN 451-1:2017 Method of testing fly ash - Part 1: Determination of free calcium oxide content
EN 450-1:2012 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
EN 413-2:2016 Masonry cement - Part 2: Test methods
ISO/IEC Guide 2:2004 Standardization and related activities General vocabulary
EN 12878:2014 Pigments for the colouring of building materials based on cement and/or lime - Specifications and methods of test
EN 45020 : 2006 STANDARDIZATION AND RELATED ACTIVITIES - GENERAL VOCABULARY
EN 196-8:2010 Methods of testing cement - Part 8: Heat of hydration - Solution method
EN 196-3:2016 Methods of testing cement - Part 3: Determination of setting times and soundness
EN 196-9:2010 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
ISO 9277:2010 Determination of the specific surface area of solids by gas adsorption — BET method
EN 480-11:2005 Admixtures for concrete, mortar and grout - Test methods - Part 11: Determination of air void characteristics in hardened concrete
CEN/TR 16045:2010 Construction Products - Assessment of release of dangerous substances - Content of regulated dangerous substances - Selection of analytical methods
EN 206:2013+A1:2016 Concrete - Specification, performance, production and conformity
CEN/TS 12390-10:2007 Testing hardened concrete - Part 10: Determination of the relative carbonation resistance of concrete
CEN/TR 16563:2013 Principles of the equivalent durability procedure
EN 15368:2008+A1:2010 Hydraulic binder for non-structural applications - Definition, specifications and conformity criteria

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.