EN ISO 16104:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Packaging - Transport packaging for dangerous goods - Test methods (ISO 16104:2003)
15-05-2003
01-08-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test requirements
5 Selection and preparation of test packagings
6 Facilities for testing
7 Test procedures
Annex A (informative) Light gauge metal packagings
Annex B (informative) Packaging types, codes and references
Annex C (normative) Special packagings
Annex D (informative) Special test requirements
Annex E (normative) Test report and specifications
Annex F (informative) Selective testing
Annex G (normative) Packaging specifications
Bibliography
ISO 16104:2003 specifies the design type test requirements for packagings intended for use in the transport of dangerous goods.
| Committee |
CEN/TC 261
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NEN EN ISO 16104 : 2003 | Identical |
| NBN EN ISO 16104 : 2003 | Identical |
| BS EN ISO 16104:2003 | Identical |
| PN EN ISO 16104 : 2006 | Identical |
| ISO 16104:2003 | Identical |
| DIN EN ISO 16104:2003-09 | Identical |
| NF EN ISO 16104 : 2003 | Identical |
| NS EN ISO 16104 : 1ED 2003 | Identical |
| I.S. EN ISO 16104:2003 | Identical |
| UNE-EN ISO 16104:2004 | Identical |
| I.S. EN ISO 16101:2004 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING |
| DIN EN ISO 16101:2004-12 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING |
| BS EN ISO 16101:2004 | Packaging. Transport packaging for dangerous goods. Plastics compatibility testing |
| ISO 16101:2004 | Packaging — Transport packaging for dangerous goods — Plastics compatibility testing |
| 06/30148624 DC : 0 | EN 15507 - PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - COMPARATIVE MATERIAL TESTING OF POLYETHYLENE GRADES |
| EN ISO 16101:2004 | Packaging - Transport packaging for dangerous goods - Plastics compatibility testing (ISO 16101:2004) |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| EN ISO 2431:2011 | Paints and varnishes - Determination of flow time by use of flow cups (ISO 2431:2011) |
| EN 22234 : 1992 | PACKAGING - COMPLETE, FILLED TRANSPORT PACKAGES - STACKING TEST USING STATIC LOAD |
| EN 22206:1992 | Packaging - Complete, filled transport packages - Identification of parts when testing (ISO 2206:1987) |
| ISO 2137:2007 | Petroleum products and lubricants — Determination of cone penetration of lubricating greases and petrolatum |
| ISO 12048:1994 | Packaging — Complete, filled transport packages — Compression and stacking tests using a compression tester |
| EN ISO 12048:2000 | Packaging - Complete, filled transport packages - Compression and stacking tests using a compression tester (ISO 12048:1994) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 2234:2000 | Packaging — Complete, filled transport packages and unit loads — Stacking tests using a static load |
| ISO 9001:2015 | Quality management systems — Requirements |
| ASTM D 4359 : 1990 | TEST METHOD FOR DETERMINING WHETHER A MATERIAL IS A LIQUID OR A SOLID |
| ISO 2206:1987 | Packaging — Complete, filled transport packages — Identification of parts when testing |
| ISO 2431:2011 | Paints and varnishes — Determination of flow time by use of flow cups |