• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN ISO 3506-4:2009

Current
Current

The latest, up-to-date edition.

Mechanical properties of corrosion-resistant stainless steel fasteners - Part 4: Tapping screws (ISO 3506-4:2009)
Published date

15-11-2009

Foreword
Introduction
1 Scope
2 Normative references
3 Designation, marking and finish
4 Chemical composition
5 Mechanical properties
6 Test methods
Annex A (normative) - Description of the groups and grades
                      of stainless steels
Annex B (informative) - Stainless steel for cold heading
                        and extruding
Annex C (informative) - Austenitic stainless steels with
                        particular resistance to chloride
                        induced stress corrosion
Annex D (informative) - Time-temperature diagram of
                        intergranular corrosion in
                        austenitic stainless steels,
                        grade A2 (18/8 steels)
Annex E (informative) - Magnetic properties for austenitic
                        stainless steels
Bibliography

ISO 3506-4:2009 specifies the mechanical properties of tapping screws made of austenitic, martensitic and ferritic steel grades of corrosion-resistant stainless steels, when tested over an ambient temperature range of 10 °C to 35 °C. Properties vary at higher or lower temperatures.It applies to tapping screws with threads from ST2,2 up to and including ST8, in accordance with ISO 1478.It does not apply to screws with special properties such as weldability.

Committee
CEN/TC 185
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

BS EN 1090-5:2017 Execution of steel structures and aluminium structures Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications
14/30297831 DC : 0 BS EN 1090-4 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
DIN EN 1090-5:2017-07 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
DIN EN 1090-5 E : 2017 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
PREN 1090-4 : DRAFT 2014 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
I.S. EN 1090-5:2017 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
EN 1090-5:2017 Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications

ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
ISO 16426:2002 Fasteners — Quality assurance system
ISO 3651-2:1998 Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid
ISO 8044:2015 Corrosion of metals and alloys Basic terms and definitions
ISO 16048:2003 Passivation of corrosion-resistant stainless-steel fasteners
ISO 3651-1:1998 Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in nitric acid medium by measurement of loss in mass (Huey test)
ISO 1478:1999 Tapping screws thread
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
ISO 4954:1993 Steels for cold heading and cold extruding

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.