ONORM EN ISO 1043-1 : 2012 AMD 1 2016
|
PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMERS AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011)
|
ONORM EN ISO 1183-2 : 2004
|
PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD
|
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
ISO 1167-2:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
|
ISO 1133-1:2011
|
Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
|
ONORM EN 12201-2 : 2013
|
PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES
|
ISO 6964:1986
|
Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
|
ONORM EN ISO 12162 : 2010
|
THERMOPLASTICS MATERIALS FOR PIPES AND FITTINGS FOR PRESSURE APPLICATIONS - CLASSIFICATION, DESIGNATION AND DESIGN COEFFICIENT
|
ISO 9080:2012
|
Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
|
ISO 13477:2008
|
Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
|
ISO 18553:2002
|
Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
|
ISO 13479:2009
|
Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes
|
ISO 12162:2009
|
Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
|
ISO 6259-1:2015
|
Thermoplastics pipes Determination of tensile properties Part 1: General test method
|
ISO 13478:2007
|
Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
|
ISO 16871:2003
|
Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering
|
ONORM EN ISO 1183-1 : 2013
|
PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 1: IMMERSION METHOD, LIQUID PYKNOMETER METHOD AND TITRATION METHOD (ISO 1183-1:2012)
|
ISO 472:2013
|
Plastics Vocabulary
|
ONORM EN ISO 472 : 2013
|
PLASTICS - VOCABULARY (ISO 472:2013)
|
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
ISO 1183-1:2012
|
Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
|
ISO 1183-2:2004
|
Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
|
ISO 15512:2016
|
Plastics Determination of water content
|
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
|
ONORM EN ISO 13479 : 2010
|
POLYOLEFIN PIPES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF RESISTANCE TO CRACK PROPAGATION - TEST METHOD FOR SLOW CRACK GROWTH ON NOTCHED PIPES
|
ONORM EN 12201-3 : 2013
|
PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS
|
ONORM EN ISO 1133-1 : 2012
|
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 1: STANDARD METHOD (ISO 1133-1:2011)
|
ISO 1133-2:2011
|
Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
|
ONORM EN 12201-4 : 2012
|
PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 4: VALVES
|
ISO 1043-1:2011
|
Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
|
ONORM EN ISO 15512 : 2017
|
PLASTICS - DETERMINATION OF WATER CONTENT (ISO 15512:2016)
|
ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
|