VDI/VDE 2617 Blatt 2.2:2000-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Accuracy of coordinate measuring machines - Parameters and their reverification - Form measurement
Hardcopy , PDF
German - English
01-07-2000
04-05-2023
Preliminary note
1 Purpose and scope of application
2 Principles and parameters
3 Acceptance testing
4 Interim checks
References
The document describes parameters for assessing the accuracy of coordinate measuring machines (CMMs) and methods for checking accuracy data.
| DevelopmentNote |
DRAFT 2016 issued in December 2016. (12/2016)
|
| DocumentType |
Standard
|
| Pages |
19
|
| PublisherName |
Verlag des Vereins Deutscher Ingenieure
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| VDI/VDE 2617 Blatt 6.3:2008-12 | Accuracy of coordinate measuring machines - Characteristics and their checking - Coordinate measuring machines with multiple probing systems |
| VDI/VDE 2617 Blatt 6.1:2007-05 | Accuracy of coordinate measuring machines - Characteristics and their testing - Coordinate measuring machines with optical probing - Code of practice for the application of DIN EN ISO 10360 to coordinate measuring machines with optical sensors for lateral structures |
| VDI/VDE 2631 Blatt 2:2014-06 | Form measurement - Verification of the signal transmission chain |
| VDI/VDE 2617 Blatt 7:2008-09 | Accuracy of coordinate measuring machines - Parameters and their checking - Estimation of measurement uncertainty of coordinate measuring machines by means of simulation |
| VDI/VDE 2617 Blatt 5:2010-12 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts |
| VDI/VDE 2617 Blatt 2.1:2014-03 | Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement |
| VDI/VDE 2631 Blatt 6:2016-08 | Form measurement - Determination of the straightness deviation of the linear guide |
| VDI/VDE 2617 Blatt 9:2009-06 | Accuracy of coordinate measuring machines - Characteristics and their reverification - Acceptance and reverification tests for Articulated Arm Coordinate Measuring Machines |
| VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12 | VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors |
| VDI/VDE 2617 Blatt 11:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets |
| VDI/VDE 2617 Blatt 5.1:2011-01 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with ball plates |
| ISO 12181-2:2011 | Geometrical product specifications (GPS) — Roundness — Part 2: Specification operators |
| ISO 12181-1:2011 | Geometrical product specifications (GPS) — Roundness — Part 1: Vocabulary and parameters of roundness |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| DIN ISO 1101:1985-03 | TECHNICAL DRAWINGS, GEOMETRICAL TOLERANCING, TOLERANCES OF FORM, ORIENTATION, LOCATION AND RUNOUT - GENERALITIES, DEFINITIONS, SYMBOLS ON DRAWINGS |
| ISO 12780-1:2011 | Geometrical product specifications (GPS) — Straightness — Part 1: Vocabulary and parameters of straightness |
| ISO 12781-2:2011 | Geometrical product specifications (GPS) — Flatness — Part 2: Specification operators |
| ISO 12781-1:2011 | Geometrical product specifications (GPS) — Flatness — Part 1: Vocabulary and parameters of flatness |
| ISO 12180-1:2011 | Geometrical product specifications (GPS) — Cylindricity — Part 1: Vocabulary and parameters of cylindrical form |
| ISO 12780-2:2011 | Geometrical product specifications (GPS) — Straightness — Part 2: Specification operators |
| ISO 12180-2:2011 | Geometrical product specifications (GPS) — Cylindricity — Part 2: Specification operators |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.