VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12
Current
Current
The latest, up-to-date edition.
VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors
Available format(s)
Hardcopy , PDF
Language(s)
German - English
Published date
01-12-2011
Publisher
£90.38
Excluding VAT
Preliminary note
Introduction
1 Scope
2 Fundamentals
3 Sensor types
4 Acceptance test
5 Monitoring
6 Material- and geometry-dependent
effects
Annex A - Structural resolution for
dimensional measurements
Annex B - Synopsis: Old and new notation
of symbols
Bibliography
The purpose of this guideline is to define specifica-tions and procedures for testing coordinate measur-ing machines (CMMs) with sensors relying on the principle of X-ray computed tomography (CT sen-sors) (see VDI/VDE 2630 Part 1.1 for a definition).
| DevelopmentNote |
Also available as VDI/VDE 2630-1-3. (08/2009)
|
| DocumentType |
Standard
|
| Pages |
0
|
| PublisherName |
Verlag des Vereins Deutscher Ingenieure
|
| Status |
Current
|
| Supersedes |
| VDI/VDE 2630 Blatt 1.1:2016-11 | Computed tomography in dimensional measurement - Fundamentals and definitions |
| VDI/VDE 2617 Blatt 5:2010-12 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts |
| VDI/VDE 2617 Blatt 2.1:2014-03 | Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement |
| VDI/VDE 2617 Blatt 11:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets |
| VDI/VDE 2630 Blatt 1.2:2010-11 | Computed tomography in dimensional measurement - Influencing variables on measurement results and recommendations for computed tomography dimensional measurements |
| VDI/VDE 2630 Blatt 2.1:2015-06 | Computed tomography in dimensional measurement - Determination of the uncertainty of measurement and the test process suitability of coordinate measurement systems with CT sensors |
| VDI/VDE 2617 Blatt 5.1:2011-01 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with ball plates |
| VDA PART 5:2022 | Volume 5 Practical Guide |
| DIN EN ISO 1:2015-03 (Draft) | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STANDARD REFERENCE TEMPERATURE FOR THE SPECIFICATION OF GEOMETRICAL AND DIMENSIONAL PROPERTIES (ISO 1:2016) |
| DIN EN ISO 10360-4:2003-06 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE TEST AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 4: CMMS USED IN SCANNING MODE |
| ISO 10360-4:2000 | Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode |
| DIN EN ISO 10360-9:2014-04 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING SYSTEMS (CMS) - PART 9: CMMS WITH MULTIPLE PROBING SYSTEMS (ISO 10360-9:2013) |
| ISO 10360-6:2001 | Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features |
| EN ISO 3650:1998 | Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998) |
| DIN EN ISO 10360-1:2003-07 | Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 1: Vocabulary (ISO 10360-1:2000 + Corr 1:2002) (includes Corrigendum AC:2002); German version EN ISO 10360-1:2000 + AC:2002 |
| DIN ISO/TS 23165:2008-08 | |
| DIN EN ISO 10360-7:2011-09 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 7: CMMs equipped with imaging probing systems (ISO 10360-7:2011) |
| ISO 10360-1:2000 | Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary |
| ISO 1:2016 | Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties |
| DIN EN ISO 14253-1:2013-12 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - PART 1: DECISION RULES FOR PROVING CONFORMITY OR NONCONFORMITY WITH SPECIFICATIONS (ISO 14253-1:2013) |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| VDI/VDE 2617 Blatt 9:2009-06 | Accuracy of coordinate measuring machines - Characteristics and their reverification - Acceptance and reverification tests for Articulated Arm Coordinate Measuring Machines |
| ISO 3650:1998 | Geometrical Product Specifications (GPS) — Length standards — Gauge blocks |
| VDI/VDE 2617 Blatt 2.2:2000-07 | Accuracy of coordinate measuring machines - Parameters and their reverification - Form measurement |
| DIN EN ISO 10360-2:2010-06 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009) |
| VDI/VDE 2617 Blatt 5:2010-12 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts |
| VDI 1000:2017-02 | VDI Standardisation Work - Principles and procedures |
| VDI/VDE 2617 Blatt 7:2008-09 | Accuracy of coordinate measuring machines - Parameters and their checking - Estimation of measurement uncertainty of coordinate measuring machines by means of simulation |
| DIN EN ISO 10360-5:2011-01 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 5: CMMS USING SINGLE AND MULTIPLE STYLUS CONTACTING PROBING SYSTEMS |
| VDI/VDE 2617 Blatt 2.1:2014-03 | Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement |
| VDI/VDE 2630 Blatt 1.4:2010-06 | Computed tomography in dimensional metrology - Measurement procedure and comparability |
| VDI/VDE 2617 Blatt 6.3:2008-12 | Accuracy of coordinate measuring machines - Characteristics and their checking - Coordinate measuring machines with multiple probing systems |
| VDI/VDE 2617 Blatt 10:2011-01 | Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests of lasertrackers |
| VDI/VDE 2630 Blatt 1.2:2010-11 | Computed tomography in dimensional measurement - Influencing variables on measurement results and recommendations for computed tomography dimensional measurements |
| EN ISO 10360-3:2000 | Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 3: CMMs with the axis of a rotary table as the forth axis (ISO 10360-3:2000) |
| ENV 13005 : DRAFT 1999 | GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT |
| VDI/VDE 2630 Blatt 1.1:2016-11 | Computed tomography in dimensional measurement - Fundamentals and definitions |
| DIN EN ISO 10360-3:2000-08 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE TEST AND REVERIFICATION TEST FOR COORDINATE MEASURING MACHINES (CMM) - PART 3: CMMS WITH THE AXIS OF A ROTARY TABLE AS THE FOURTH AXIS |
| DIN EN ISO 10360-6:2009-01 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 6: ESTIMATION OF ERRORS IN COMPUTING GAUSSIAN ASSOCIATED FEATURES |
| EN ISO 10360-2:2009 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009) |
| EN ISO 10360-7:2011 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 7: CMMs equipped with imaging probing systems (ISO 10360-7:2011) |
| DIN EN ISO 10360-8:2014-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING SYSTEMS (CMS) - PART 8: CMMS WITH OPTICAL DISTANCE SENSORS (ISO 10360-8:2013) |
| ISO 10360-7:2011 | Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 7: CMMs equipped with imaging probing systems |
| VDI/VDE 2617 Blatt 5.1:2011-01 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with ball plates |
| VDI/VDE 2617 Blatt 6.1:2007-05 | Accuracy of coordinate measuring machines - Characteristics and their testing - Coordinate measuring machines with optical probing - Code of practice for the application of DIN EN ISO 10360 to coordinate measuring machines with optical sensors for lateral structures |
| VDI/VDE 2617 Blatt 8:2006-07 | Accuracy of coordinate measuring machines - Characteristics and their testing - Test suitability of measurements with coordinate measuring machines |
| VDI/VDE 2617 Blatt 2.3:2006-05 | Accuracy of coordinate measuring machines - Characteristics and checking of characteristics - Acceptance and reverification tests for coordinate measuring machines of large dimensions |
| ISO 10360-3:2000 | Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 3: CMMs with the axis of a rotary table as the fourth axis |
| VDI/VDE 2617 Blatt 12.1:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests for tactile CMM measuring microgeometries |
| VDI/VDE 2617 Blatt 11:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets |
| EN ISO 10360-5:2010 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 5: CMMs using single and multiple stylus contacting probing systems (ISO 10360-5:2010) |
| PREN ISO 10360-9 : DRAFT 2010 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 9: CMMS WITH MULTIPLE PROBING SYSTEMS |
| ISO 10360-5:2010 | Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using single and multiple stylus contacting probing systems |
| EN ISO 1:2016 | Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties (ISO 1:2016) |
| ISO 10360-2:2009 | Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring linear dimensions |
| ISO/TS 23165:2006 | Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty |
Summarise
£90.38
Excluding VAT
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.