EN ISO 3650:1998
Current
Current
The latest, up-to-date edition.
Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998)
Amended by
Published date
15-12-1998
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Nomenclature of faces
5 Basis of measurement, traceability, reference condition
6 General dimensions, material properties, marking
7 Metrological requirements
8 Calibration of gauge blocks
Annex A (informative) - Example of a device for the
comparison of gauge blocks
Annex B (informative) - Relation to the GPS matrix model
Annex C (informative) - Bibliography
Annex ZA (normative) - Normative references to international
publications with their relevant European publications
This International Standard specifies the most important design and metrological characteristics of gauge blocks with a rectangular cross section and a nominal length ln ranging from 0,5 mm to 1000 mm.Limit deviations and tolerances are stated for the calibration grade K and for the grades 0, 1 and 2 for various measuring purposes.
| Committee |
CEN/TC 290
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| SupersededBy |
| Standards | Relationship |
| NF EN ISO 3650 : 1999 | Identical |
| DIN EN ISO 3650:1999-02 | Identical |
| NBN EN ISO 3650 : 1999 COR 2009 | Identical |
| BS EN ISO 3650:1999 | Identical |
| ISO 3650:1998 | Identical |
| SS-EN ISO 3650 : 1998 | Identical |
| PN EN ISO 3650 : 2000 | Identical |
| I.S. EN ISO 3650:1999 | Identical |
| NEN EN ISO 3650 : 1999 | Identical |
| NS EN ISO 3650 : 1998 AC 2009 | Identical |
| UNE-EN ISO 3650:2000 | Identical |
| PREN 932-5 : DRAFT 2009 | TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION |
| VDI/VDE 2617 Blatt 6.1:2007-05 | Accuracy of coordinate measuring machines - Characteristics and their testing - Coordinate measuring machines with optical probing - Code of practice for the application of DIN EN ISO 10360 to coordinate measuring machines with optical sensors for lateral structures |
| I.S. EN 932-5:2012 | TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5 - COMMON EQUIPMENT AND CALIBRATION |
| VDI/VDE 2617 Blatt 5:2010-12 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts |
| VDI/VDE 2617 Blatt 2.1:2014-03 | Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement |
| VDI/VDE 2617 Blatt 12.1:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests for tactile CMM measuring microgeometries |
| VDI/VDE/DGQ 2618 Blatt 7.1:2010-12 | INSPECTION OF MEASURING AND TEST EQUIPMENT - TEST INSTRUCTION FOR STEEL SQUARES 90 DEGREE |
| VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12 | VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors |
| VDI/VDE/DGQ 2618 Blatt 10.5:2010-08 | Inspection of measuring and test equipment - Test instruction for depth micrometers |
| VDI/VDE/DGQ 2618 Blatt 10.7:2010-08 | Inspection of measuring and test equipment - Test instruction for internal micrometers with 2-point contact |
| VDI/VDE/DGQ 2618 Blatt 10.6:2010-08 | Inspection of measuring and test equipment - Test instruction for height micrometers |
| VDI/VDE/DGQ 2618 Blatt 16.1:2009-10 | Inspection of measuring and test equipment - Test instruction for height gauges |
| VDI/VDE/DGQ 2618 Blatt 4.4:2009-09 | Inspection of measuring and test equipment - Test instruction for reference gauges with plane-parallel or spherical measuring faces and for spherical-end gauges and internal callipers |
| VDI/VDE 2634 Blatt 3:2008-12 | Optical 3D-measuring systems - Multiple view systems based on area scanning |
| DIN EN 932-5:2012-05 | Tests for general properties of aggregates - Part 5: Common equipment and calibration |
| 09/30205556 DC : 0 | BS EN 932-5 - TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION |
| BS EN 932-5:2012 | Tests for general properties of aggregates Common equipment and calibration |
| UNE-EN 932-5:2012 | Tests for general properties of aggregates - Part 5: Common equipment and calibration |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) — Masterplan |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 1:2016 | Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO/IEC Guide 99:2007 | International vocabulary of metrology — Basic and general concepts and associated terms (VIM) |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
Summarise
Sorry this product is not available in your region.