DIN EN 681-1:2016-07 (Draft)
Withdrawn
Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber; German and English version prEN 681-1:2016
Hardcopy , PDF
German, German - English
07-01-2016
03-28-2022
Foreword
Introduction
1 Scope
2 Normative references
3 Classification
4 Requirements
5 Test pieces and temperature
6 Quality
7 Factory product control tests
8 Storage
9 Designation
10 Marking and labelling
Annexes
A (normative) Determination of stress relaxation in
tension
B (normative) Determination of compression set in hot
water at 110 Degree C
C (normative) Determination of splice strength
D (informative) Guidance on storage of seals
ZA (informative) Clauses of this European
Standard addressing the provisions of the
EU Construction Products Directive
This standard is included in DIN Handbook 12/5, 13-2, 13-5, 15-6 and 62-1. Defines requirements for materials used in vulcanized rubber seals for cold potable water supply (up to 50 degree C), hot potable and non-potable water supply (to 110 degree C) and drainage, sewerage and rainwater systems (continuous flow to 45 degree C and intermittent flow up to 95 degree C). Applies to seals for all materials including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastic.
| DevelopmentNote |
Partly supersedes DIN 4060 issue 12-1988. (09/2000) DRAFT 2016 issued in July 2016. (07/2016)
|
| DocumentType |
Draft
|
| Pages |
71
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Withdrawn
|
| Standards | Relationship |
| NEN EN 681-1 : 1996 AMD 3 2005 | Identical |
| BS EN 681-1:1996 | Identical |
| NS EN 681-1 : 96 AMD 3 2005 | Identical |
| NF EN 681-1 : 1996 AMD 3 2005 | Identical |
| I.S. EN 681-1:1996 | Identical |
| NBN EN 681-1 : 1996 AMD 3 2005 | Identical |
| UNE-EN 681-1:1996 | Identical |
| DIN 8063-3:2002-06 | PIPE JOINTS AND COMPONENTS OF UNPLASTICIZED POLY(VINYLCHLORIDE) (PVC U) FOR PIPES UNDER PRESSURE - PART 3: UNIONS - DIMENSIONS |
| DIN V 4034-1:2004-08 | PREFABRICATED CONCRETE MANHOLES, UNREINFORCED, STEEL FIBRE AND REINFORCED FOR DRAINS AND SEWERS - TYPE 1 AND TYPE 2 - PART 1: REQUIREMENTS, TEST METHODS AND EVALUATION OF CONFORMITY |
| DIN V 1201:2004-08 | CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED FOR DRAINS AND SEWERS - TYPE 1 AND TYPE 2 - REQUIREMENTS, TEST METHODS AND EVALUATION OF CONFORMITY |
| DIN 28602:2000-05 | DUCTILE IRON PIPES AND FITTINGS - BOLTED GLAND JOINTS - ASSEMBLY, SOCKETS, COUNTER RING, SEALING RING, BOLTS AND NUTS |
| DIN 16874:2000-06 | PIPES AND FITTINGS OF HIGH-DENSITY POLYETHYLENE (PE-HD) FOR CABLE DUCTING - DIMENSIONS AND TECHNICAL DELIVERY CONDITIONS |
| DIN 28601:2000-06 | DUCTILE IRON PIPES AND FITTINGS - SCREWED SOCKET JOINTS - ASSEMBLY, SOCKETS, SCREW RINGS, SEALING RINGS AND SLIP RINGS |
| DIN 28603:2002-05 | DUCTILE IRON PIPES AND FITTINGS - PUSH-IN JOINTS - SURVEY, SOCKETS AND GASKETS |
| DIN 16831-7:2004-02 | Pipe fittings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 7: Dimensions of bushings, flanges and selaing elements for socket welding |
| DIN HDBK 190 : 3ED 2006 | ROHRE, ROHRLEITUNGSTEILE UND ROHRVERBINDUNGEN AUS THERMOPLASTISCHEN KUNSTSTOFFEN |
| DIN HDBK 160 : 4ED 2006 | WASSERVERSORGUNG 4 - ROHRE, FORMSTUECKE UND ZUBEHOER FUER WASSERLEITUNGEN (B) |
| DIN 16962-12:1999-10 | PIPE JOINTS AND COMPONENTS OF POLYPROPYLENE (PP) FOR PIPES UNDER PRESSURE, PP-H 100, PP-B 80 AND PP-R 80 - PART 12: FLANGE ADAPTERS, FLANGES, SEALING RINGS FOR SOCKET WELDING; DIMENSIONS |
| DIN 16963-11:1999-10 | PIPE JOINTS AND COMPONENTS OF POLYETHYLENE (PE) FOR PIPES UNDER PRESSURE, PE 80 AND PE 100 - PART 11: FLANGE ADAPTERS, FLANGES, SEALING RINGS FOR SOCKET WELDING - DIMENSIONS |
| DIN 16917-1:2015-10 | PIPES AND FITTINGS MADE OF THERMOPLASTIC MATERIALS WITH PROFILED WALL AND SMOOTH PIPE INSIDE - LARGE PIPES OVER DN 1200 FOR UNDERGROUND INSTALLATION - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| DIN 8063-3:1980-07 | PIPE JOINT ASSEMBLIES AND FITTINGS FOR UNPLASTICIZED POLYVINYL CHLORIDE (PVC-U) PRESSURE PIPES - PART 3: DIMENSIONS OF SCREWED PIPE JOINT ASSEMBLIES |
| DIN HDBK 50 : 9ED 2000 | ABWASSERTECHNIK 2 - ROHRE UND FORMSTUECKE FUER DIE GEBAEUDEENTWAESSERUNG |
| DIN HDBK 13-2 : 11ED 2017 | ABWASSERTECHNIK 2 - ROHRE UND FORMSTUECKE FUER DIE GEBAEUDEENTWAESSERUNG |
| DIN HDBK 259 : 4ED 2007 | ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN |
| DIN HDBK 62-2 : 8ED 2010 | |
| DIN HDBK 12/5 : 9ED 2013 | |
| DIN HDBK 62-1 : 8ED 2010 | WASSERVERSORGUNG 2 - GUSS-, STAHLBETON- UND STAHLROHRE FUER WASSERLEITUNGEN |
| DIN HDBK 13-5 : 5ED 2015 | ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN |
| DIN HDBK 62 CD : 7ED 2004 | WASSERVERSORGUNG 2 - GUSS-, KUNSTSTOFF-, STAHLBETON- UND STAHLROHRE FUER WASSERLEITUNGEN |
| DIN HDBK 15-6 : 1ED 2012 |
| ISO 3302:1990 | Rubber — Dimensional tolerances for use with products |
| ISO 3951:1989 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| ISO 2285:2013 | Rubber, vulcanized or thermoplastic — Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing |
| ISO 9691:1992 | Rubber — Recommendations for the workmanship of pipe joint rings — Description and classification of imperfections |
| ISO 4661-1:1993 | Rubber, vulcanized or thermoplastic — Preparation of samples and test pieces — Part 1: Physical tests |
| ISO 3384:2005 | Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression at ambient and at elevated temperatures |
| ISO 3387:2012 | Rubber — Determination of crystallization effects by hardness measurements |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 471:1995 | Rubber — Temperatures, humidities and times for conditioning and testing |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 816:1983 | Rubber, vulcanized — Determination of tear strength of small test pieces (Delft test pieces) |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| ISO 1629:2013 | Rubber and latices — Nomenclature |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.