• There are no items in your cart

EN 1090-1:2009+A1:2011

Current
Current

The latest, up-to-date edition.

Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
Published date

11-23-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Requirements
5 Evaluation methods
6 Evaluation of conformity
7 Classification and designation
8 Marking
Annex A (informative) - Guidelines for preparation of the
        component specification
Annex B (normative) - Assessment of factory production
        control
Annex ZA (informative) - Clauses of this European Standard
         Addressing the provisions of EU Construction
         Products Directive (CPD)
Bibliography

This European Standard specifies requirements for conformity assessment of performance characteristics for structural steel and aluminium components as well as for kits placed on the market as construction products. The conformity assessment covers the manufacturing characteristics, and where appropriate the structural design characteristics.This European Standard covers also the conformity assessment of steel components used in composite steel and concrete structures.The components can be used directly or in construction works or as structural components in the form of kits.This European Standard applies to series and non-series structural components including kits.The components can be made of hot rolled or cold formed constituent products or constituent products produced with other technologies. They may be produced of sections/profiles with various shapes, flat products (plates, sheet, strip), bars, castings, forgings made of steel and aluminium materials, unprotected or protected against corrosion by coating or other surface treatment, e.g. anodising of aluminium.This European Standard covers structural cold formed members and sheeting as defined in EN 1993-1-3 and EN 1999-1-4.This European Standard does not cover conformity assessment of components for suspended ceilings, rails or sleepers for use in railway systems.NOTEFor certain steel and aluminium components, particular specifications for performance and other requirements have been developed. The particular specifications may be issued as an EN or as Clauses within an EN. An example is given in EN 13084-7 for single wall steel chimneys and steel liners. Such particular specifications will take precedence in case of non-compliance with the requirements of this European Standard.

Committee
CEN/TC 135
DevelopmentNote
2009 Edition Re-Issued in November 2011 & incorporates AMD 1 2011. (12/2011) Supersedes PREN 1090-1. (02/2012)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

UNE-EN 50341-1:2017 Overhead electrical lines exceeding AC 1 kV - Part 1: General requirements - Common specifications
PD CEN/TR 17052:2017 Guidelines on implementing EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures Requirements for conformity assessment of structural components
PREN 14199 : DRAFT 2013 EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES
BS EN 1090-5:2017 Execution of steel structures and aluminium structures Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications
03/106158 DC : DRAFT APR 2003 EN 14653-1 - MANUALLY OPERATED HYDRAULIC SHORING SYSTEMS FOR GROUNDWORK SUPPORT - PART 1: PRODUCT SPECIFICATIONS
13/30280743 DC : 0 BS EN 14199 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES
10/30212126 DC : 0 BS EN 845-2 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
DIN EN 1999-1-4:2010-05 Eurocode 9 - Design of aluminium structures - Part 1-4: Cold-formed structural sheeting; German version EN 1999-1-4:2007 + AC:2009
BS EN 50341-1:2012 Overhead electrical lines exceeding AC 1 kV General requirements. Common specifications
UNI EN 1999-1-5 : 2007 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-5: SHELL STRUCTURES
15/30320416 DC : 0 BS EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
14/30297831 DC : 0 BS EN 1090-4 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
BS EN 845-2 : 2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
DIN EN 1090-5:2017-07 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
CEN/TR 1317-6 : 2012 ROAD RESTRAINT SYSTEMS - PART 6: PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS
CEN/TR 17052:2017 Guidelines on implementing EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
DIN EN 1090-2:2011-10 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
14/30312146 DC : 0 BS EN 1090-5 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED ALUMINIUM ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
PD CEN/TR 16949:2016 Road restraint system. Pedestrian restraint system. Pedestrian parapets
CEN/TR 16949:2016 Road restraint system - Pedestrian restraint system - Pedestrian parapets
PREN 1090-2 : DRAFT 2015 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
S.R. CEN/TR 17052:2017 GUIDELINES ON IMPLEMENTING EN 1090-1:2009+A1:2011, EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS
UNE-EN 1090-2:2011 Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures
UNI CEN/TR 1317-6 : 2012 ROAD RESTRAINT SYSTEMS - PART 6: PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS
I.S. EN 1999-1-1:2007 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES (INCLUDING IRISH NATIONAL ANNEX)
UNE-EN 1090-5:2017 Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications
EN 50341-1:2012 Overhead electrical lines exceeding AC 1 kV - Part 1: General requirements - Common specifications
DIN EN 1090-2:2015-07 (Draft) EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
UNI EN 1090-2 : 2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
DIN EN 13107:2015-09 SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS
I.S. EN 845-2:2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
I.S. EN 13107:2015 SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS
DIN EN 1999-1-1:2014-03 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES
PD CEN/TR 1317-6:2012 Road restraint systems Pedestrian restraint system. Pedestrian parapets
DIN EN 1999-1-5:2010-05 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-5: SHELL STRUCTURES
16/30328759 DC : 0 BS EN 13814-1 - SAFETY OF AMUSEMENT RIDES AND AMUSEMENT DEVICES - PART 1: DESIGN AND MANUFACTURE
DIN EN 1090-5 E : 2017 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
BS EN 1999-1-4 : 2007 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-4: COLD-FORMED STRUCTURAL SHEETING
ISO/TS 20273:2017 Guidelines on weld quality in relationship to fatigue strength
PREN 1337-1 : DRAFT 2018 STRUCTURAL BEARINGS - PART 1: GENERAL
PREN 12699 : DRAFT 2013 EXECUTION OF SPECIAL GEOTECHNICAL WORK - DISPLACEMENT PILES
CEI EN 50341-1 : 2013 OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS
UNI EN 1999-1-4 : 2011 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-4: COLD-FORMED STRUCTURAL SHEETING
EN 1090-2:2008+A1:2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
PREN 1090-4 : DRAFT 2014 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
BS EN 1090-2 : 2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
I.S. EN 1993-4-1:2007 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-1: SILOS
EEMUA 207 : 2009 DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION
UNI EN 1993-1-9 : 2005 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-9: FATIGUE
UNI EN 1993-1-1 : 2014 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
12/30260570 DC : 0 BS EN 50341-1 - OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS
UNI EN 1999-1-1 : 2014 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES
18/30365863 DC : 0 BS EN 1337-1 - STRUCTURAL BEARINGS - PART 1: GENERAL
PD ISO/TS 20273:2017 Guidelines on weld quality in relationship to fatigue strength
PREN 845-2 : DRAFT 2012 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
PREN 13031-1 : DRAFT 2017 GREENHOUSES - DESIGN AND CONSTRUCTION - PART 1: COMMERCIAL PRODUCTION GREENHOUSES
IEC 60913:2013 Railway applications - Fixed installations - Electric traction overhead contact lines
EN 1999-1-5:2007/AC:2009 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-5: SHELL STRUCTURES
BS EN 13107:2015 Safety requirements for cableway installations designed to carry persons. Civil engineering works
EN 845-2:2013+A1:2016 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
PREN 50341-1 : DRAFT 2012 OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS
S.R. CEN/TR 1317-6:2012 ROAD RESTRAINT SYSTEMS - PART 6: PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS
13/30280740 DC : 0 BS EN 12699 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - DISPLACEMENT PILES
12/30265747 DC : 0 BS EN 845-2 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
BS EN 1999-1-5:2007 Eurocode 9. Design of aluminium structures Shell structures
I.S. EN 50341-1:2012 OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS
KTA 3205.2 : 2015 COR 2016 COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT
I.S. EN 1090-2:2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
S.R. CEN/TR 16949:2016 ROAD RESTRAINT SYSTEM - PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS
17/30354665 DC : 0 BS EN 13031-1 - GREENHOUSES - DESIGN AND CONSTRUCTION - PART 1: COMMERCIAL PRODUCTION GREENHOUSES
I.S. EN 1090-5:2017 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
EN 1999-1-4:2007/A1:2011 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-4: COLD-FORMED STRUCTURAL SHEETING
EN 1090-5:2017 Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications
DIN EN 1999-1-5:2017-03 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-5: SHELL STRUCTURES

93/68/EEC : 1993 AMD 2 1998 COUNCIL DIRECTIVE 93/68/EEC OF 22.7.93 AMENDING DIRECTIVES 87/404/EEC, 88/378/EEC, 89/106/EEC, 89/336/EEC, 89/392/EEC, 89/686/EEC, 90/384/EEC, 90/385/EEC, 90/396/EEC, 91/263/EEC, 92/42/EEC AND 73/23/EEC
EN ISO 19011:2011 COR 2011 GUIDELINES FOR AUDITING MANAGEMENT SYSTEMS (ISO 19011:2011)
EN 14783:2013 Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements
EN 1011-4:2000/A1:2003 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 4: ARC WELDING OF ALUMINIUM AND ALUMINIUM ALLOYS
EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 14782:2006 Self-supporting metal sheet for roofing, external cladding and internal lining - Product specification and requirements
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
ISO 14731:2006 Welding coordination Tasks and responsibilities
ISO 7976-2:1989 Tolerances for building — Methods of measurement of buildings and building products — Part 2: Position of measuring points
EN 1090-3:2008 Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures
EN 13501-2:2016 Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services
EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
ISO 12944-1:2017 Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 1: General introduction
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 10025-5:2004 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
EN ISO 14731:2006 Welding coordination - Tasks and responsibilities (ISO 14731:2006)
ISO 9001:2015 Quality management systems — Requirements
EN 1090-2:2008+A1:2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
ISO 7976-1:1989 Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments
ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules
EN 1990:2002/A1:2005/AC:2010 EUROCODE - BASIS OF STRUCTURAL DESIGN
ISO 17123-1:2014 Optics and optical instruments Field procedures for testing geodetic and surveying instruments Part 1: Theory
EN ISO 15607:2003 Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.