EN 50109-2-3:1995
Withdrawn
Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 2-3: Particular requirements for contacts of electrical connectors
06-22-1995
07-23-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Requirements
5 Classification and designation
6 Test and acceptance requirements
7 User information
Annexes
A Crimping tool description (normative)
B Turrets and positioners (normative)
C Test contacts (normative)
D Methods of test for crimped joints (normative)
E Mechanical endurance testing (normative)
Part 2-3 of this European Standard specifies detail requirements for hand crimping tools incorporating a system of multiple indentors for use with removable male and female contacts of electrical connectors and similar components. Two sizes of tool are covered, as follows: a tool for contacts with crimp barrel size 12 to 20 inclusive (tool reference EN 50109-2-3-100), see clause 5; a tool for contacts with crimp barrel size 20 and smaller (tool reference EN 50109-2-3-300), see clause 5. It includes requirements for crimped joints made with the tools
| Committee |
CLC/TC 46X
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Withdrawn
|
| Standards | Relationship |
| NBN EN 50109 2-3 : 2000 | Identical |
| DIN EN 50109-2-3:1995-11 | Identical |
| PN EN 50109-2-3 : 2002 | Identical |
| NF EN 50109-2-3 : 2004 | Identical |
| NEN EN 50109-2-3 : 1995 | Identical |
| BS EN 50109-2-3:1996 | Identical |
| CEI EN 50109-2-3 : 1997 | Identical |
| I.S. EN 50109-2-3:1997 | Identical |
| UNE-EN 50109-2-3:1993 | Identical |
| CEI EN 50109-2-5 : 1997 | HAND CRIMPING TOOLS - TOOLS FOR THE CRIMP TERMINATION OF ELECTRIC CABLES AND WIRES FOR LOW FREQUENCY AND RADIO FREQUENCY APPLICATIONS - PART 2-5: PARTICULAR REQUIREMENTS FOR THE TERMINATION OF TWIN-AX CABLE FOR DATABUS APPLICATIONS |
| I.S. EN 50109-2-5:1997 | HAND CRIMPING TOOLS - TOOLS FOR THE CRIMP TERMINATION OF ELECTRIC CABLES AND WIRES FOR LOW FREQUENCY AND RADIO FREQUENCY APPLICATIONS - PART 2-5: PARTICULAR REQUIREMENTS FOR THE TERMINATION OF TWIN-AX CABLE FOR DATABUS APPLICATIONS |
| EN 50109-2-5:1995 | Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 2-5: Particular requirements for the termination of twin-ax cable for databus applications |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| CECC 22000 : 1993 | GENERIC SPECIFICATION: RADIO FREQUENCY COAXIAL CONNECTORS |
| ISO 6507-2:2005 | Metallic materials — Vickers hardness test — Part 2: Verification and calibration of testing machines |
| ISO 6507-3:2005 | Metallic materials — Vickers hardness test — Part 3: Calibration of reference blocks |
| ISO 468:1982 | Surface roughness — Parameters, their values and general rules for specifying requirements |
| EN 50109-1:1995 | Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 1: General requirements and tests |
| ISO 4287-1:1984 | Surface roughness — Terminology — Part 1: Surface and its parameters |