GEIA TA HB 0009 : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RELIABILITY PROGRAM HANDBOOK
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2013
Superseded date
06-21-2022
Superseded by
US$404.00
Excluding Tax where applicable
1. Introduction
2. Activities
3. METHODS
Annex A - List of References (Informative)
Annex B - Symbols and Abbreviated Terms (Informative)
Specifies 'how to' guidance to industry and government for the reliability Activities and Methods contained in ANSI/GEIA-STD-0009 for developing reliable products and systems, successfully demonstrating them during test and evaluation, and sustaining them throughout the system/product life cycle.
| Committee |
G-41
|
| DevelopmentNote |
Supersedes GEIA HB 0009. (04/2013)
|
| DocumentType |
Standard
|
| Pages |
475
|
| PublisherName |
Government Electronics & Information Technology Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| MIL-STD-2119 Revision A:1990 | Design Requirements for Printed-Wiring Electrical Backplane Assemblies |
| MIL-HDBK-965 Base Document:1996 | Acquisition Practices for Parts Management (No S/S Document) |
| MIL-STD-1530 Revision D:2016 | Aircraft Structural Integrity Program (ASIP) |
| ISO 2859-3:2005 | Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures |
| QML 31032 : 20171107 | QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION - MIL-PRF-31032 - PRINTED CIRCUIT BOARD/PRINTED WIRING BOARD, GENERAL SPECIFICATION FOR |
| SAE JA1012_201108 | A Guide to the Reliability-Centered Maintenance (RCM) Standard |
| MIL-STD-883 Revision K:2016 | Microcircuits |
| SAE JA1011_200908 | Evaluation Criteria for Reliability-Centered Maintenance (RCM) Processes |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| DEFSTAN 00-42(PT1)/2(2008) : 2008 | RELIABILITY AND MAINTAINABILITY (R&M) ASSURANCE ACTIVITY - PART 1: ONE-SHOT DEVICES/SYSTEMS |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| IEC 62628:2012 | Guidance on software aspects of dependability |
| IEC 61014:2003 | Programmes for reliability growth |
| MIL-STD-975 Revision M:1994 | NASA STANDARD ELECTRICAL, ELECTRONIC, AND ELECTROMECHANICAL (EEE) PARTS LIST (NO S/S DOCUMENT) |
| GEIA TB 0003 : 2009 | COUNTERFEIT PARTS & MATERIALS RISK MITIGATION |
| MIL-HDBK-83578 Base Document:1999 | Criteria for Explosive Systems and Devices used on Space Vehicles (No S/S Document) |
| IEC 61165:2006 | Application of Markov techniques |
| MIL-HDBK-2173 Base Document:1998 | Reliability-Centered Maintenance Requirements for Naval Aircraft, Weapons Systems and Support Equipment (Refer to Naval Aviation RCM Process, Guide Manual, NAVAIR 00-25-403) |
| MIL-HDBK-781 Revision A:1996 | Reliability Test Methods, Plans, and Environments for Engineering Development, Qualification, and Production |
| MIL-STD-750 Revision F:2011 | Test Methods for Semiconductor Devices |
| MIL-STD-1916 Base Document:1996 | DOD Preferred Methods for Acceptance of Product |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| SAE ARP1332D | Wave Soldering Procedure |
| ISO 2859-0:1995 | Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
| ARMP-8 : 1991 | RELIABILITY & MAINTAINABILITY (R&M) IN THE PROCUREMENT OF OFF-THE-SHELF (OTS) EQUIPMENT |
| MIL STD 1843 : 0 | RELIABILITY-CENTERED MAINTENANCE FOR AIRCRAFT, ENGINES AND EQUIPMENT |
| SAE AS9100D | Quality Management Systems - Requirements for Aviation, Space, and Defense Organizations |
| MIL-STD-414 Base Document:1957 | SAMPLING PROCEDURE AND TABLE FOR INSPECTION BY VARIABLES FOR PERCENT DEFECTIVE (S/S BY ASQC-Z1.9) |
| AIAA R 013 : 1992 | RECOMMENDED PRACTICE FOR SOFTWARE RELIABILITY |
| MIL-HDBK-338 Revision B:1998 | Electronic Reliability Design Handbook |
| MIL-STD-965 Revision B:1993 | PARTS CONTROL PROGRAM (S/S BY MIL-HDBK-965) |
| ISO 8422:2006 | Sequential sampling plans for inspection by attributes |
| DEFSTAN 00-42(PT3)/4(2011) : 2011 | RELIABILITY AND MAINTAINABILITY ASSURANCE GUIDE - PART 3: R&M CASE |
| MIL-HDBK-472 Base Document:1966 | Maintainability Prediction |
| SAE J1739_200901 | Potential Failure Mode and Effects Analysis in Design (Design FMEA), Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA) |
| MIL-STD-2000 Revision A:1991 | STANDARD REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES (NO S/S DOCUMENT) |
| ISO/TR 8550:1994 | Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots |
| MIL-STD-882 Revision E:2012 | System Safety |
| MIL-HDBK-2165 Base Document:1995 | Testability Program for Systems and Equipments |
| MIL-HDBK-108 Base Document:1960 | Quality Control and Reliability - Sampling Procedures and Tables for Life and Reliability Testing (Based on Exponential Distribution) (No S/S Document) |
| IEC 60300-3-11:2009 | Dependability management - Part 3-11: Application guide - Reliability centred maintenance |
| MIL-STD-1472 Revision G:2012 | Human Engineering |
| MIL H 38534 : B (1) | HYBRID MICROCIRCUITS, GENERAL SPECIFICATION FOR |
| IEEE 1633-2016 REDLINE | IEEE Recommended Practice on Software Reliability |
| MIL-HDBK-310 Base Document:1997 | Global Climatic Data for Developing Military Products |
| GEIA STD 0009 : 2008 | RELIABILITY PROGRAM STANDARD FOR SYSTEMS DESIGN, DEVELOPMENT AND MANUFACTURING |
| MIL-HDBK-470 Revision A:1997 | Designing and Developing Maintainable Products and Systems, Volume I |
| MIL-STD-3018 Base Document:2007 | Parts Management (S/S by MIL-STD-11991) |
| MIL-STD-1629 Revision A:1980 | PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS AND CRITICALITY ANALYSIS (NO S/S DOCUMENT) |
| MIL-HDBK-189 Revision C:2011 | Reliability Growth Management |
| MIL-STD-690 Revision D:2005 | Failure Rate (FR) Sampling Plans and Procedures |
| MIL-STD-105 Revision E:1989 | Sampling Procedures and Tables for Inspection by Attributes (See Notice 3 for Replacement Information) |
| MIL-HDBK-727 Base Document:1984 | Design Guidance for Producibility |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.