15/30295265 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
BS EN 13204 - DOUBLE ACTING HYDRAULIC RESCUE TOOLS FOR FIRE AND RESCUE SERVICE USE - SAFETY AND PERFORMANCE REQUIREMENTS
Hardcopy , PDF
30-09-2016
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Information for use
6 Marking
Annex A (normative) - List of hazards
Annex B (normative) - Noise test code (Grade 2 of
accuracy)
Annex C (normative) - Product Performance Data Sheet
Annex D (informative) - Examples of technical measures
for noise reduction
Annex E (normative) - General verification requirements
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
BS EN 13204.
Committee |
FSH/17
|
DocumentType |
Draft
|
Pages |
54
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
PREN 13204 : DRAFT 2015 | Identical |
EN 854:2015 | Rubber hoses and hose assemblies - Textile reinforced hydraulic type - Specification |
CEN Guide 414:2017 | Safety of machinery - Rules for the drafting and presentation of safety standards |
EN 1746:1998 | Safety of machinery - Guidance for the drafting of the noise clauses of safety standards |
ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
EN 856:2015 | Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification |
EN 61000-6-1:2007 | Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments |
ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
EN ISO 1402:2009 | Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009) |
ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
EN 50565-2:2014 | Electric cables - Guide to use for cables with a rated voltage not exceeding 450/750 V (U0/U) - Part 2: Specific guidance related to EN 50525 cable types |
ISO 11546-2:1995 | Acoustics Determination of sound insulation performances of enclosures Part 2: Measurements in situ (for acceptance and verification purposes) |
EN 61000-6-3:2007/A1:2011/AC:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
ISO 3949:2009 | Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification |
ISO 5598:2008 | Fluid power systems and components Vocabulary |
ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
EN 61310-3:2008 | Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators |
EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
IEC 61000-6-1 : 3.0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS |
EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
IEC 61310-3:2007 | Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators |
ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
EN ISO 7751:2016 | Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure (ISO 7751:2016) |
EN ISO 11820 : 1996 | ACOUSTICS - MEASUREMENTS ON SILENCERS IN SITU |
EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
EN ISO 11688-2 : 2000 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN |
EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
EN 857:2015 | Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification |
ISO/TR 14121-2:2012 | Safety of machinery — Risk assessment — Part 2: Practical guidance and examples of methods |
EN 10210-2:2006/AC:2007 | HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 2: TOLERANCES, DIMENSIONS AND SECTIONAL PROPERTIES |
EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
ISO 10619-1:2011 | Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature |
ISO 11820:1996 | Acoustics — Measurements on silencers in situ |
EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
EN ISO 6945:1996/A1:2000 | RUBBER HOSES - DETERMINATION OF ABRASION RESISTANCE OF THE OUTER COVER |
IEC 61000-6-3:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments |
EN ISO 11546-2:2009 | Acoustics - Determination of sound insulation performances of enclosures - Part 2: Measurements in situ (for acceptance and verification purposes) (ISO 11546-2:1995) |
EN 764 : 1994 | PRESSURE EQUIPMENT - TERMINOLOGY AND SYMBOLS - PRESSURE, TEMPERATURE, VOLUME |
EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
EN 659:2003+A1:2008/AC:2009 | PROTECTIVE GLOVES FOR FIREFIGHTERS |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
EN 10025-2:2004/AC:2005 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS |
EN ISO 9614-2 : 1996 | ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 2: MEASUREMENT BY SCANNING |
EN ISO 3949:2014 | PLASTICS HOSES AND HOSE ASSEMBLIES - TEXTILE-REINFORCED TYPES FOR HYDRAULIC APPLICATIONS - SPECIFICATION (ISO 3949:2009) |
ISO 9001:2015 | Quality management systems — Requirements |
EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
ISO 7751:2016 | Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressure |
EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
ISO 1402:2009 | Rubber and plastics hoses and hose assemblies Hydrostatic testing |
EN 853:2015 | Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
EN 837-1:1996/AC:1998 | PRESSURE GAUGES - BOURDON TUBE PRESSURE GAUGES - DIMENSIONS, METROLOGY, REQUIREMENTS AND TESTING |
EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.