11/30249105 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 12516-1 - INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 1: TABULATION METHOD FOR STEEL VALVE SHELLS
Hardcopy , PDF
English
30-11-2014
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Material groups and material temperature limitations
6 Pressure/temperature (p/t) ratings
7 Temperature effects
8 Dimensions
9 Auxiliary connections
10 Requirements for Special Class
11 End dimensions
12 Marking
Annex A (informative) - Relationship between DN,
NPS, pipe inside diameter Dni and pipe
outside diameter OD
Annex B (normative) - Radiography procedure and
acceptance standards
Annex C (normative) - Magnetic particle examination
procedure and acceptance standards
Annex D (normative) - Liquid penetrant examination
procedure and acceptance standards
Annex E (normative) - Ultrasonic examination procedure
and acceptance standards
Annex F (normative) - Methods used for establishing
pressure-temperature ratings
Annex G (normative) - Requirement for Limited Class
valves in sizes DN 65 and smaller
Annex H (informative) - Material groups
Annex I (informative) - ASTM/ASME material groups
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 97/23/EC
(Pressure Equipment Directive)
Bibliography
BS EN 12516-1
| Committee |
PSE/18/1
|
| DocumentType |
Draft
|
| Pages |
180
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 12516-1 : DRAFT 2011 | Identical |
| EN ISO 9692-1:2013 | Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013) |
| EN 444:1994 | Non-destructive testing - General principles for radiographic examination of metallic materials by X- and gamma-rays |
| ASTM E 446 : 2015 : REDLINE | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
| ASTM E 186 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN 12680-1:2003 | Founding - Ultrasonic examination - Part 1: Steel castings for general purposes |
| EN 736-2:2016 | Valves - Terminology - Part 2: Definition of components of valves |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN 10228-1:1999 | Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection |
| PREN 12516-2 : DRAFT 2011 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 2: CALCULATION METHOD FOR STEEL VALVE SHELLS |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 10222-3:2017 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 10228-3:2016 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
| ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 584-1:2006 | Non-destructive testing - Industrial radiographic film - Part 1: Classification of film systems for industrial radiography |
| EN 1369:2012 | Founding - Magnetic particle testing |
| EN 462-1:1994 | Non-destructive testing - Image quality of radiographs - Part 1: Image quality indicators (wire type) - Determination of image quality value |
| ASTM E 280 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings |
| EN 12681:2003 | Founding - Radiographic examination |
| EN 12517-1:2006 | Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels |
| EN 12517-2:2008 | Non-destructive testing of welds - Part 2: Evaluation of welded joints in aluminium and its alloys by radiography - Acceptance levels |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 12760:2016 | Industrial valves - Socket welding ends for steel valves |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| EN 19:2016 | Industrial valves - Marking of metallic valves |
| EN 736-3:2008 | Valves - Terminology - Part 3: Definition of terms |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.