ASTM A 29/A29M : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought
14-08-2020
English
01-12-2016
CONTAINED IN VOL. 01.05, 2017 Defines a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to carbon and alloy steel bars under each of the following ASTM specifications (or under any other ASTM specification which invokes this specification or portions thereof).
Committee |
A 01
|
DevelopmentNote |
Supersedes ASTM A 29 (06/2000) Supersedes FED STD 48 (02/2004)
|
DocumentType |
Redline
|
Pages |
17
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification2 covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to carbon and alloy steel bars under each of the following ASTM specifications (or under any other ASTM specification which invokes this specification or portions thereof):
Title of Specification | ASTM |
Hot-Rolled Carbon Steel Bars: | |
Steel Bars, Carbon, Quenched and Tempered | A321 |
Steel Bars and Shapes, Carbon Rolled from “T' Rails | A499 |
Steel Bars, Carbon, Merchant Quality, M-Grades | A575 |
Steel Bars, Carbon, Hot-Wrought, Special Quality | A576 |
Steel Bars, Carbon, Merchant Quality, Mechanical Properties | A663/A663M |
Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties | A675/A675M |
Steel Bars for Springs, Carbon and Alloy | A689 |
Cold-Finished Carbon Steel Bars: | |
Steel Bars, Carbon and Alloy, Cold-Finished | A108 |
Cold-Drawn Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements | A311/A311M |
Hot-Rolled Alloy Steel Bars: | |
Steel Bars, Alloy, Standard Grades | A322 |
Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements | A304 |
Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered | A434/A434M |
Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both | A739 |
Cold-Finished Alloy Steel Bars: | |
Steel Bars, Alloy, Hot-Rolled or Cold-Finished, Quenched and Tempered | A434/A434M |
Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping Components | A696 |
A These designations refer to the latest issue of the respective specifications, which appear either in the Annual Book of ASTM Standards, Vol 01.05, or as reprints obtainable from ASTM. |
1.2In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named.
1.3The values stated in inch-pound units or SI units are to be regarded as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.4For purposes of determining conformance to this specification and the various material specifications referenced in 1.1, dimensional values shall be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.
Note 1:Specification A29/A29M previously listed dimensional tolerances for cold-finished bars; these are now found in Specification A108.
ASTM F 1145 : 2005 : R2011 | Standard Specification for Turnbuckles, Swaged, Welded, Forged |
ASTM D 7577 : 2012 | Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends |
MS39210 Revision K:2018 | NUTS, TUBE COUPLING - SAFETY SLEEVE COMPRESSION TYPE |
ASTM A 663/A663M : 2017 : REDLINE | Standard Specification for Steel Bars, Carbon, Merchant Quality, Mechanical Properties |
A-A-55603 Revision A:2012 | Clamp, Guy (Pole Line) |
MS39199 Revision G:2012 | NIPPLE, TUBE-SAFETY SLEEVE COMPRESSION TYPE, BULKHEAD MOUNTING |
MIL-DTL-20277-1 Base Document:2007 | Knife, Combat |
MIL-DTL-17060 Revision G:2009 | MOTORS, ALTERNATING CURRENT, INTEGRAL-HORSEPOWER, SHIPBOARD USE |
ASTM A 920/A920M : 2014 : REDLINE | Standard Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, Mechanical Properties |
ASTM A 485 : 2017 : REDLINE | Standard Specification for High Hardenability Antifriction Bearing Steel |
BS ISO 13628-10 : 2005 AMD 16775 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 10: SPECIFICATION FOR BONDED FLEXIBLE PIPE |
GGG-P-781 Revision E:1996 | PULLER, MECHANICAL PULLER ATTACHMENT, MECHANICAL, AND PULLER SET, MECHANICAL |
ASTM A 321 : 1990 : R2001 | Standard Specification for Steel Bars, Carbon, Quenched and Tempered (Withdrawn 2007) |
ASTM A 466/A466M : 2007 | Standard Specification for Weldless Chain |
ASTM A 921/A921M : 1993 : R2011 | Standard Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, for Subsequent Hot Forging |
ASTM A 391/A391M : 2007 : R2012 | Standard Specification for Grade 80 Alloy Steel Chain |
ASTM A 739 : 1990 : REV A : R2000 | Standard Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both |
ASTM F 844 : 2007 : REV A : R2013 | Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use |
ASTM A 696 : 2017 : REDLINE | Standard Specification for Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping Components |
ASTM A 355 : 1989 : R2012 | Standard Specification for Steel Bars, Alloys, for Nitriding |
ASTM F 917 : 2014 : REDLINE | Standard Specification for Commercial Food Waste Disposers |
ASTM A 355 : 1989 : R2006 | Standard Specification for Steel Bars, Alloys, for Nitriding |
ASTM F 860 : 2007 : R2013 | Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Multiple Tank, Rackless Conveyor Type |
ASTM F 1145 : 2005 : R2017 | Standard Specification for Turnbuckles, Swaged, Welded, Forged |
ASTM F 1150 : 2016 : REDLINE | Standard Specification for Commercial Food Waste Pulper and Waterpress Assembly |
ASTM A 311/A311M : 2004 : R2010 | Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements |
MS21077 Revision H:1994 | NUT, SELF-LOCKING, PLATE, TWO LUG, FLOATING, NON-METALLIC INSERT, STEEL 125 KSI FTU, 250 DEG F |
ASME B107.410 : 2008 | STRUCK TOOLS |
MIL-S-63540 Revision C:1995 | STUD, SELF-CLINCHING GENERAL SPECIFICATION FOR |
MIL-P-21143 Revision B:1984 | PIN, STRAIGHT, HEADLESS (DOWEL) |
AASHTO M 227M/M 227 : 2013 | SPECIFICATION FOR STEEL BARS, CARBON, MERCHANT QUALITY, MECHANICAL PROPERTIES |
MS39207 Revision H:2018 | Elbows, Tube - Safety Sleeve Compression Type, 90 Degree |
AN6027 Revision 5:2013 | COUPLING HALF, QUICK DISCONNECT |
ASTM A 576 : 2017 : REDLINE | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality |
ASTM A 295 : 1998 | Standard Specification for High-Carbon Anti-Friction Bearing Steel |
ASTM A 952/A952M : 2002 | Standard Specification for Forged Grade 80 and Grade 100 Steel Lifting Components and Welded Attachment Links |
ASTM F 860 : 2007 | Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Multiple Tank, Rackless Conveyor Type |
MIL-PRF-6085 Revision E:2011 | LUBRICATING OIL, INSTRUMENT, AIRCRAFT, LOW VOLATILITY |
AASHTO M 255M/M 255 : 2005 : R2013 | SPECIFICATION FOR STEEL BARS, CARBON, HOT-WROUGHT, SPECIAL QUALITY, MECHANICAL PROPERTIES |
AASHTO M 255M/M 255 : 2005 : R2013 | SPECIFICATION FOR STEEL BARS, CARBON, HOT-WROUGHT, SPECIAL QUALITY, MECHANICAL PROPERTIES |
ASTM A 499 : 2015 : REDLINE | Standard Specification for Steel Bars and Shapes, Carbon Rolled from “T” Rails |
ASTM A 125 : 1996 : R2001 | Standard Specification for Steel Springs, Helical, Heat-Treated |
SAE J 2484 : 2012 | FASTENER PART STANDARD - MACHINE SCREWS |
ASTM A 466/A466M : 2007 : R2012 | Standard Specification for Weldless Chain |
ASTM A 295/A295M : 2014 : REDLINE | Standard Specification for High-Carbon Anti-Friction Bearing Steel |
ASTM A 434 : 2006 : R2012 | Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered |
ASTM A 575 : 1996 : R2007 | Standard Specification for Steel Bars, Carbon, Merchant Quality, M-Grades |
ASTM A 1089/A1089M : 2014 | Standard Specification for Highly Loaded Anti-Friction Bearing Steel |
ASTM A 125 : 1996 | Standard Specification for Steel Springs, Helical, Heat-Treated |
ASTM A 675/A675M : 2014 : REDLINE | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties |
ASTM F 1145 : 2005 | Standard Specification for Turnbuckles, Swaged, Welded, Forged |
ASTM A 689 : 1997 : R2002 | Standard Specification for Carbon and Alloy Steel Bars for Springs |
ASTM A 521 : 2003 | Standard Specification for Steel, Closed-Impression Die Forgings for General Industrial Use |
UNE-EN ISO 4404-1:2012 | Petroleum and related products - Determination of the corrosion resistance of fire-resistant hydraulic fluids - Part 1: Water-containing fluids (ISO 4404-1:2012) |
ISO 4404-1:2012 | Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 1: Water-containing fluids |
I.S. EN ISO 4404-1:2012 | PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS (ISO 4404-1:2012) |
ASME PV CODE 2C : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS |
AASHTO M 281 : 1996 | SPECIFICATION FOR STEEL FENCE POSTS AND ASSEMBLIES, HOT-WROUGHT |
ASME B31.4 : 2016 | PIPELINE TRANSPORTATION SYSTEMS FOR LIQUIDS AND SLURRIES |
ASTM A 413/A413M : 2007 : R2012 | Standard Specification for Carbon Steel Chain |
MIL-DTL-18866 Revision J:2015 | Fittings, Hydraulic Tube, Flared, 37 Degree and Flareless, General Specification for |
MS39202 Revision G:2012 | ELBOWS, PIPE TO TUBE - SAFETY SLEEVE COMPRESSION TYPE, 90 DEGREE, MALE PIPE END |
ASTM A 689 : 1997 : R2007 : EDT 1 | Standard Specification for Carbon and Alloy Steel Bars for Springs |
MS39201 Revision G:2012 | NIPPLE, TUBE-SAFETY SLEEVE COMPRESSION TYPE |
AWS A5.17/A5.17M : 1997 | SPECIFICATION FOR CARBON STEEL ELECTRODES AND FLUXES FOR SUBMERGED ARC WELDING |
ASTM A 125 : 1996 : R2013 | Standard Specification for Steel Springs, Helical, Heat-Treated |
SAE J 2485 : 2012 | FASTENER PART STANDARD - MACHINE SCREW NUTS (METRIC AND INCH) |
API SPEC 20E : 2017 | ALLOY AND CARBON STEEL BOLTING FOR USE IN THE PETROLEUM AND NATURAL GAS INDUSTRIES |
ASTM A 1 : 2000 : R2010 | Standard Specification for Carbon Steel Tee Rails |
GGG-C-313 Revision D:1995 | CHISELS, HAND: CAPE, DIAMOND POINT, COLD, ROUND NOSE, AND SIDE CUTTING |
MIL-DTL-32373 Base Document:2011 | Plug, Machine Thread, Magnetic: Drain |
AWS A5.5/A5.5M : 2014 | SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING |
ASTM A 413/A413M : 2007 | Standard Specification for Carbon Steel Chain |
CSA M430 : 1990 : R2011 | ROOF AND ROCK BOLTS, AND ACCESSORIES |
ASTM F 844 : 2007 : REV A | Standard Specification for Washers, Steel, Plain (Flat), Unhardened for General Use |
CSA M430 : 1990 : R2016 | ROOF AND ROCK BOLTS, AND ACCESSORIES |
A-A-55606 Revision A:2013 | Anchor, Guy, and Rods, Anchor |
AASHTO M 169 : 2015 | SPECIFICATION FOR STEEL BARS, CARBON AND ALLOY, COLD-FINISHED |
ASTM F 857 : 2017 : REDLINE | Standard Specification for Hot Water and Chemical Sanitizing Commercial Dishwashing Machines, Stationary Rack Type |
ASTM A 711 : 2004 | Standard Specification for Steel Forging Stock |
API SPEC 17K : 2017 | SPECIFICATION FOR BONDED FLEXIBLE PIPE |
ASTM A 914/A914M : 2016 : REDLINE | Standard Specification for Steel Bars Subject to Restricted End-Quench Hardenability Requirements |
ASTM A 1 : 2000 | Standard Specification for Carbon Steel Tee Rails |
ASTM F 860 : 2007 : R2018 : EDT 1 | Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Multiple Tank, Rackless Conveyor Type |
ASTM A 521/A521M : 2006 | Standard Specification for Steel, Closed-Impression Die Forgings for General Industrial Use |
ASTM A 311/A311M : 2004 | Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements |
ASTM A 321 : 1990 : R1995 : EDT 1 | Standard Specification for Steel Bars, Carbon, Quenched and Tempered |
ASTM A 355 : 1989 : R2000 | Standard Specification for Steel Bars, Alloys, for Nitriding |
ASTM A 909/A909M : 2006 : R2011 | Standard Specification for Steel Forgings, Microalloy, for General Industrial Use |
ASTM A 729/A729M : 2017 : REDLINE | Standard Specification for Carbon and Alloy Steel Axles, Heat-Treated, for Mass Transit and Electric Railway Service |
DIN EN ISO 4404-1:2012-10 | PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS (ISO 4404-1:2012) |
ASTM D 7577 : 2012 : R2016 | Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends |
MS35338 Revision L:1994 | WASHER, LOCK SPRING, HELICAL, REGULAR (MEDIUM) SERIES |
UNI EN ISO 4404-1 : 2013 | PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS |
ASTM A 125 : 1996 : R2007 | Standard Specification for Steel Springs, Helical, Heat-Treated |
ASTM A 355 : 1989 : R2017 | Standard Specification for Steel Bars, Alloys, for Nitriding |
ASTM A 739 : 1990 : REV A : R2006 | Standard Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both |
ASTM A 65 : 2007 : R2013 | Standard Specification for Steel Track Spikes (Withdrawn 2022) |
ASTM A 921/A921M : 1993 : R2016 | Standard Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, for Subsequent Hot Forging |
ASTM A 575 : 1996 : R2013 : EDT 1 | Standard Specification for Steel Bars, Carbon, Merchant Quality, M-Grades |
MIL-DTL-20277 Revision K:2014 | KNIFE, COMBAT; AND SHEATH, GENERAL SPECIFICATION FOR |
MIL-S-5000 Revision E:1982 | STEEL, CHROME-NICKEL-MOLYBDENUM (4340) BARS AND REFORGING STOCK |
GGG-P-840 Revision B:1994 | PUNCHES AND DIES, AND PUNCH AND DIE SETS: METAL CUTTING, HAND; AND PUNCH, CLIP, SHEET METAL |
ASTM A 434/A434M : 2017-03 | SPECIFICATION FOR STEEL BARS, ALLOY, HOT-WROUGHT OR COLD-FINISHED, QUENCHED AND TEMPERED |
MIL-S-24700 Base Document:1988 | STUFFING TUBES FOR REFERENCE ELECTRODES, IMPRESSED CURRENT CATHODIC PROTECTION (METRIC) |
ASTM A 739 : 1990 : REV A : R2016 | Standard Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both |
ASTM A 952/A952M : 2002 : R2016 | Standard Specification for Forged Grade 80 and Grade 100 Steel Lifting Components and Welded Attachment Links |
CSA M430 : 1990 : R2007 | ROOF AND ROCK BOLTS, AND ACCESSORIES |
AASHTO M 277 : 2006 : R2010 | SPECIFICATION FOR WIRE ROPE AND SOCKETS FOR MOVABLE BRIDGES |
ASTM A 909/A909M : 2006 : R2016 | Standard Specification for Steel Forgings, Microalloy, for General Industrial Use |
ASTM A 304 : 2016 : REDLINE | Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements |
ASTM A 702 : 2013-11 | SPECIFICATION FOR STEEL FENCE POSTS, HOT WROUGHT |
ASTM A 1075 : 2012 | Standard Specification for Flanged Steel U-Channel Posts |
ASTM A 521/A521M : 2006 : R2016 | Standard Specification for Steel, Closed-Impression Die Forgings for General Industrial Use (Withdrawn 2018) |
ASTM A 921/A921M : 1993 : R2005 | Standard Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, for Subsequent Hot Forging |
ASTM A 1 : 2000 : R2005 | Standard Specification for Carbon Steel Tee Rails |
ASTM A 535 : 1985 | Specification for Special-Quality Ball and Roller Bearing Steel (Withdrawn 1998) |
ASTM A 973/A973M : 2007 : R2012 | Standard Specification for Grade 100 Alloy Steel Chain |
ASTM A 1 : 2000 : R2018 | Standard Specification for Carbon Steel Tee Rails |
ASTM A 311/A311M : 2004 : R2015 | Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements |
EN ISO 4404-1:2012 | Petroleum and related products - Determination of the corrosion resistance of fire-resistant hydraulic fluids - Part 1: Water-containing fluids (ISO 4404-1:2012) |
ACI 355.3R : 2011 | GUIDE FOR DESIGN OF ANCHORAGE TO CONCRETE: EXAMPLES USING ACI 318 APPENDIX D |
ASTM A 575 : 1996 : R2002 | Standard Specification for Steel Bars, Carbon, Merchant Quality, M-Grades |
ASTM A 973/A973M : 2007 | Standard Specification for Grade 100 Alloy Steel Chain |
ASTM A 689 : 1997 : R2013 : EDT 1 | Standard Specification for Carbon and Alloy Steel Bars for Springs |
GGG-P-836 Revision A:1995 | PUNCH AND DIE, KNOCKOUT |
ASTM A 711/A711M : 2017 : REDLINE | Standard Specification for Steel Forging Stock |
ASTM A 31 : 2014 : REDLINE | Standard Specification for Steel Rivets and Bars for Rivets, Pressure Vessels |
ASTM A 391/A391M : 2007 | Standard Specification for Grade 80 Alloy Steel Chain |
BS ISO 4404:1998 | Petroleum and related products. Determination of the corrosion resistance of water-containing fire-resistant fluids for hydraulic systems |
ASTM A 534 : 2017 : REDLINE | Standard Specification for Carburizing Steels for Anti-Friction Bearings |
ASTM A 739 : 1990 : REV A : R2012 | Standard Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both |
NASM 21083 : 2004 | NUT, SELF-LOCKING, HEXAGON, NON-METALLIC INSERT, LOW HEIGHT, 250 DEGREES F |
CSA C22.2 No. 2556 : 2015 | WIRE AND CABLE TEST METHODS |
ASTM F 432 : 2013 : REDLINE | Standard Specification for Roof and Rock Bolts and Accessories |
ASTM A 909 : 2003 | Standard Specification for Steel Forgings, Microalloy, for General Industrial Use |
ASTM A 434 : 2006 | Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered |
ASTM A 125 : 1996 : R2013 : EDT 1 | Standard Specification for Steel Springs, Helical, Heat-Treated |
ASTM A 65 : 2007 | Standard Specification for Steel Track Spikes |
ASTM A 850 : 1985 | Specification for Steel Bars, Carbon Manganese Merchang Quality with 50 KSI (345 MPA) Yield Point (Withdrawn 1990) |
ASTM A 1075 : 2012 : R2017 : EDT 1 | Standard Specification for Flanged Steel U-Channel Posts |
ASTM F 2643 : 2015 : REDLINE | Standard Specification for Powered Pot, Pan and Utensil Washing Sinks |
ASTM A 952/A952M : 2002 : R2010 | Standard Specification for Forged Grade 80 and Grade 100 Steel Lifting Components and Welded Attachment Links |
ASTM A 521/A521M : 2006 : R2011 | Standard Specification for Steel, Closed-Impression Die Forgings for General Industrial Use |
ASTM A 575 : 1996 | Standard Specification for Steel Bars, Carbon, Merchant Quality, M-Grades |
ASTM A 909/A909M : 2006 | Standard Specification for Steel Forgings, Microalloy, for General Industrial Use |
BS EN ISO 4404-1:2012 | Petroleum and related products. Determination of the corrosion resistance of fire-resistant hydraulic fluids Water-containing fluids |
CSA G40.20 G40.21 : 2013 | GENERAL REQUIREMENTS FOR ROLLED OR WELDED STRUCTURAL QUALITY STEEL/STRUCTURAL QUALITY STEEL |
ASTM A 675/A675M : 2014 : REDLINE | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties |
ASTM A 434/A434M : 2017-03 | SPECIFICATION FOR STEEL BARS, ALLOY, HOT-WROUGHT OR COLD-FINISHED, QUENCHED AND TEMPERED |
ASTM A 689 : 1997 : R2002 | Standard Specification for Carbon and Alloy Steel Bars for Springs |
ASTM A 499 : 2015 : REDLINE | Standard Specification for Steel Bars and Shapes, Carbon Rolled from “T” Rails |
FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
ASTM A 700 : 2014 | Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment |
MIL-STD-163 Revision C:1978 | STEEL MILL PRODUCTS PREPARATION FOR SHIPMENT AND STORAGE |
FED-STD-183 Revision C:1980 | CONTINUOUS IDENTIFICATION MARKING OF IRON AND STEEL PRODUCTS |
AIAG B 1 : 1988 | BAR CODE SYMBOLOGY STANDARD |
ASTM A 304 : 2016 : REDLINE | Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements |
AIAG B 5 : 1993 | PRIMARY METALS TAG APPLICATION STANDARD |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.