MIL-DTL-17060 Revision G:2009
Current
Current
The latest, up-to-date edition.
Motors, Alternating Current, Integral-Horsepower, Shipboard Use
Available format(s)
PDF
Published date
08-01-2009
Publisher
£13.91
Excluding VAT
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
APPENDIX A - EXAMINATION OF SERVICE A MOTORS
APPENDIX B - ENGINEERING DRAWINGS TECHNICAL CONTENT
REQUIREMENTS
APPENDIX C - TEST PROCEDURES FOR MOTOR EFFICIENCY
APPENDIX D - TEST REPORT TECHNICAL CONTENT REQUIREMENTS
APPENDIX E - CERTIFICATION DATA/REPORT TECHNICAL CONTENT
REQUIREMENTS
APPENDIX F - SHOCK TEST REPORT TECHNICAL CONTENT REQUIREMENTS
APPENDIX G - EQUIPMENT AIRBORNE AND STRUCTUREBORNE NOISE
MEASUREMENTS TEST REPORT - TECHNICAL CONTENT
REQUIREMENTS
APPENDIX H - INSPECTION AND TEST PLAN - TECHNICAL CONTENT
REQUIREMENTS
INDEX
Specifies the requirements for three-phase, alternating current (AC) motors for shipboard use in frame sizes not less than 182.
| DevelopmentNote |
Supersedes MIL M 17060 (F). (01/2009)
|
| DocumentType |
Standard
|
| Pages |
199
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Current
|
| Supersedes |
This specification covers the requirements for three-phase, alternating current (AC) motors for shipboard use in frame sizes not less than 182.
| MIL-DTL-24151 Revision B:2016 | Doors, Roller Curtain and Hinged Slat, and AssociatedOperating Equipment |
| MIL-DTL-917 Revision F:2014 | Electric Power Equipment, Basic Requirements for |
| MIL STD 11991 : A | GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES |
| MIL-DTL-32408 Base Document:2012 | Integral Motor Pump (IMP) (No S/S Document) |
| MIL-DTL-32572 Base Document:2017 | Anchor Windlass, Electro-Mechanical, Vertical, Two-Speedand Variable-Speed |
| MIL-PRF-24755 Revision B:2010 | Fans, Vaneaxial, High Pressure, Naval Shipboard |
| MIL-PRF-18953 Revision C:2005 | Fans, Vaneaxial and Tubeaxial, Ventilation and Air Conditioning, Naval Shipboard |
| MIL-DTL-17840 Revision D:2018 | Pump, Centrifugal, Close-Coupled, Navy Standard (for Surface Ships Application) |
| MIL-I-24092 Revision D:1993 | Insulating Varnishes and Solventless Resins for Application by the Dip Process |
| A-A-59589 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Filling Slot, Dimension Series 03 |
| NEMA MW 1000 : 2016 | MAGNET WIRE |
| MIL-STD-2037 Base Document:1991 | Procedure To Obtain Certification for Electric Motor Sealed Insulation Systems |
| A-A-59586 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 04 |
| A-A-59641 Revision B:2011 | Bearing, Ball, Annular, Double Row, Angular Contact, Filling Slot, Vertex of Contact Angles Outside Bearing, Dimension Series 33 |
| ASTM A 47/A47M : 1999 | Standard Specification for Ferritic Malleable Iron Castings |
| MIL-C-24707-5 Base Document:1989 | Castings, Ductile Iron and Austenitic Iron |
| A-A-59640 Revision B:2011 | Bearing, Ball, Annular, Double Row, Angular Contact, Filling Slot, Vertex of Contact Angles Outside Bearing, Dimensions Series 32 |
| MIL-DTL-917 Revision F:2014 | Electric Power Equipment, Basic Requirements for |
| A-A-59629 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 Degrees Through 32 Degrees, Dimension Series 02 |
| A-A-59637 Revision B:2011 | Bearing, Ball, Annular, Double Row, Angular Contact, Non-Filling Slot, Vertex of Contact Angles Outside Bearing, Dimension Series 33 |
| ASTM A 29/A29M : 2016 : REDLINE | Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought |
| SAE AMS7276H | Rubber: Fluorocarbon (FKM) High-Temperature-Fluid Resistant Low Compression Set For Seals In Fuel Systems and Specific Engine Oil Systems |
| MIL-DTL-21248 Revision D:2015 | Ring, Retaining (Tapered and Reduced Section Type) |
| A-A-59685 Base Document:2001 | Grease, Sealed Ball and Roller Bearing |
| A-A-59596 Revision C:2009 | Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Cartridge Type Without Grease Plug, Dimension Series 33 |
| A-A-59584 Revision C:2008 | Bearing, Ball, Single Row, Radial, Non-Filling Slot, Dimension Series 02 |
| MIL-PRF-17331 Revision K:2013 | Lubricating Oil, Steam Turbine and Gear, Moderate Service |
| A-A-59632 Revision B:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 33 Degrees Through 45 Degrees, Dimension Series 10 |
| IEC TS 61934:2011 | Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses |
| MIL-DTL-1222 Revision J:2000 | Studs, Bolts, Screws and Nuts for Applications where a High Degree of Reliability is Required; General Specification for |
| A-A-59627 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 Degrees Through 22 Degrees, Dimension Series 04 |
| SAE AMS2469J | Hard Anodic Coating on Aluminum and Aluminum Alloys |
| MIL-L-19140 Revision E:1984 | Lumber and Plywood, Fire-Retardant Treated |
| ASTM A 683 : 2016 : REDLINE | Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types |
| QQ-B-654 Revision A:1980 | BRAZING ALLOYS, SILVER |
| A-A-59630 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 Degrees Through 32 Degrees, Dimension Series 03 |
| MIL-STD-740-2 Base Document:1986 | Structureborne Vibratory Acceleration Measurements Acceptance Criteria of Shipboard Equipment |
| MIL C 24707/1 : 0 | CASTINGS, FERROUS, FOR MACHINERY AND STRUCTURAL APPLICATIONS |
| SAE AMS7259E | Rubber: Fluorocarbon (FKM) High Temperature/Fluid Resistant Low Compression Set/85 to 95 Hardness For Seals In Fuel Systems and Specific Engine Oil Systems |
| MIL-I-24178 Base Document:1966 | Insulation Tape, Electrical, Semi-Cured Thermosetting Resin Treated Glass, Armature Banding, Naval Shipboard |
| A-A-59638 Revision B:2011 | Bearing, Ball, Annular, Double Row, Angular Contact, Non-Filling Slot, Vertex of Contact Angles Inside Bearing, Dimension Series 32 |
| MIL-B-17931 Revision E:1987 | Bearing, Ball, Annular, for Quiet Operation |
| MIL-STD-461 Revision G:2015 | Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment |
| ASTM D 4727/D4727M : 2017 : REDLINE | Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes |
| A-A-59626 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 Degrees through 22 Degrees, Dimension Series 03 |
| IEC 60034-18-41:2014 | Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests |
| A-A-59597 Revision C:2009 | Bearing, Ball, Annular, Double Row, Radial, Internal Self-Aligning, Dimension Series 02 |
| A-A-59636 Revision B:2011 | Bearing, Ball, Annular, Double Row, Angular Contact, Non-Filling Slot, Vertex of Contact Angles Outside Bearing, Dimension Series 32 |
| A-A-59583 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 10 |
| A-A-59600 Revision C:2009 | Bearing, Ball, Annular, Double Row, Radial, Internal Self-Aligning, Dimension Series 23 |
| ASTM B 30 : 2016 : REDLINE | Standard Specification for Copper Alloys in Ingot Form |
| A-A-59599 Revision C:2009 | Bearing, Ball, Annular, Double Row, Radial, Internal Self- Aligning, Dimension Series 22 |
| MIL S 901 : D | SHOCK TESTS, HI [HIGH IMPACT] SHIPBOARD MACHINERY, EQUIPMENT AND SYSTEMS, REQUIREMENTS FOR |
| A-A-59625 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 Degrees Through 22 Degrees, Dimension Series 02 |
| A-A-59623 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 Degrees Through 22 Degrees, Dimension Series 19 |
| MIL-STD-108 Revision E:1966 | Definitions of and Basic Requirements for Enclosures for Electric and Electronic Equipment |
| A-A-59624 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 Degrees Through 22 Degrees, Dimension Series 10 |
| A-A-59634 Revision B:2010 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 33 Degrees Through 45 Degrees, Dimension Series 03 |
| A-A-59582 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 19 |
| A-A-59587 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Filling Slot, Dimension Series 02 |
| A-A-59633 Revision B:2010 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 33 Degrees Through 45 Degrees, Dimension Series 02 |
| ASTM A 677 : 2016 : REDLINE | Standard Specification for Nonoriented Electrical Steel Fully Processed Types |
| MIL-STD-1474 Revision E:2015 | Noise Limits |
| A-A-59628 Revision C:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 Degrees through 32 Degrees, Dimension Series 10 |
| MIL-P-15024-5 Base Document:1971 | Plate, Identification |
| A-A-59635 Revision B:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 33 Degrees through 45 Degrees, Dimension Series 04 |
| IEEE 112-2004 | IEEE Standard Test Procedure for Polyphase Induction Motors and Generators |
| MIL-DTL-2036 Revision E:2014 | Enclosures for Electric and Electronic Equipment, Naval Shipboard |
| MIL-DTL-15024 Revision F:1997 | Plates and Tags for Identification of Equipment, General Specification for |
| ASTM B21/B 21M : 2014-10 | SPECIFICATION FOR NAVAL BRASS ROD, BAR, AND SHAPES |
| MIL-DTL-18240 Revision F:1997 | Fastener Element, Self-Locking, Threaded Fastener, 250 Degrees F Maximum |
| A-A-59631 Revision B:2011 | Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 Degrees Through 32 Degrees, Dimension Series 04 |
| FED-STD-H28 Revision A:1994 | Screw-Thread Standards for Federal Services |
| A-A-59598 Revision C:2009 | Bearing, Ball, Annular, Double Row, Radial, Internal Self-Aligning, Dimension Series 03 |
| A-A-59639 Revision B:2011 | Bearing, Ball, Annular, Double Row, Angular Contact, Filling Slot, Vertex of Contact Angles Inside Bearing, Dimension Series 33 |
| MIL-M-24738 Base Document:1990 | Monitors, High Temperature Motor Protection |
| A-A-59720 Base Document:2002 | Sealing and Locking Compounds, Single-Component |
| MIL-E-16298 Revision D:1989 | Electric Machines Having Rotating Parts, Accessories and Associated Support Items: Packaging of |
| A-A-59581 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Bore Diameters Under 10 MM |
| A-A-59595 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Cartridge Type Without Grease Plug, Dimension Series 32 |
| A-A-59585 Revision C:2008 | Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 03 |
Summarise
£13.91
Excluding VAT
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.