• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 2892 : 2015

Withdrawn

Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

View Superseded by
withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column)

Available format(s)

Hardcopy , PDF

Withdrawn date

20-10-2018

Language(s)

English

Published date

01-04-2015

1.1This test method covers the procedure for the distillation of stabilized crude petroleum (see Note 1) to a final cut temperature of 400 °C Atmospheric Equivalent Temperature (AET). This test method employs a fractionating column having an efficiency of 14 to 18 theoretical plates operated at a reflux ratio of 5:1. Performance criteria for the necessary equipment is specified. Some typical examples of acceptable apparatus are presented in schematic form. This test method offers a compromise between efficiency and time in order to facilitate the comparison of distillation data between laboratories.

Note 1:Defined as having a Reid vapor pressure less than 82.7 kPa (12 psi).

1.2This test method details procedures for the production of a liquefied gas, distillate fractions, and residuum of standardized quality on which analytical data can be obtained, and the determination of yields of the above fractions by both mass and volume. From the preceding information, a graph of temperature versus mass % distilled can be produced. This distillation curve corresponds to a laboratory technique, which is defined at 15/5 (15 theoretical plate column, 5:1 reflux ratio) or TBP (true boiling point).

1.3This test method can also be applied to any petroleum mixture except liquefied petroleum gases, very light naphthas, and fractions having initial boiling points above 400 °C.

1.4This test method contains the following annexes and appendixes:

1.4.1Annex A1Test Method for the Determination of the Efficiency of a Distillation Column,

1.4.2Annex A2Test Method for the Determination of the Dynamic Holdup of a Distillation Column,

1.4.3Annex A3Test Method for the Determination of the Heat Loss in a Distillation Column (Static Conditions),

1.4.4Annex A4Test Method for the Verification of Temperature Sensor Location,

1.4.5Annex A5Test Method for Determination of the Temperature Response Time,

1.4.6Annex A6Practice for the Calibration of Sensors,

1.4.7Annex A7Test Method for the Verification of Reflux Dividing Valves,

1.4.8Annex A8Practice for Conversion of Observed Vapor Temperature to Atmospheric Equivalent Temperature (AET),

1.4.9Appendix X1Test Method for Dehydration of a Sample of Wet Crude Oil, and

1.4.10Appendix X2Practice for Performance Check.

1.5The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 10.

1.7WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.

Committee
D 02
DocumentType
Test Method
Pages
34
PublisherName
American Society for Testing and Materials
Status
Withdrawn
SupersededBy
Supersedes

ASTM D 5188 : 2016 Standard Test Method for Vapor-Liquid Ratio Temperature Determination of Fuels (Evacuated Chamber and Piston Based Method)
ASTM D 6377 : 2016 Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCR<inf>x</inf > (Expansion Method)
ASTM D 1655 : 2019 Standard Specification for Aviation Turbine Fuels
ASTM D 6352 : 2015 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography
ASTM D 5191 : 2019 Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 7169 : 2018 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 7807 : 2012 Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection
ASTM D 7798 : 2015 Standard Test Method for Boiling Range Distribution of Petroleum Distillates with Final Boiling Points up to 538 °C by Ultra Fast Gas Chromatography (UF GC)
ASTM D 2887 : 2019 Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography
ASTM D 6897 : 2016 Standard Test Method for Vapor Pressure of Liquefied Petroleum Gases (LPG) (Expansion Method)
ASTM D 7213 : 2015 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in the Boiling Range from 100 °C to 615 °C by Gas Chromatography
ASTM D 5399 : 2009 : R2017 Standard Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography
ASTM D 7566 : 2019 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 6378 : 2018 : REV A Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)
ASTM D 7398 : 2011 : R2016 Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 °C to 615 °C by Gas Chromatography

View more information
£92.22
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.