• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 3375 : 2019

Current

Current

The latest, up-to-date edition.

Standard Test Method for Assessing Non-Metered Restricted Delivery Systems for Liquid Consumer Products

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-06-2019

This test method covers assessment of non-metered restricted delivery system characteristics so that they can be evaluated to a standard that signifies efficacy in limiting accessibility of liquid contents to young children.

1.1This test method covers assessment of non-metered restricted delivery system characteristics so that they can be evaluated to a standard that signifies efficacy in limiting accessibility of liquid contents to young children.

1.2This test method provides general test conditions for the determination of flow control of liquids by restricted delivery systems using mechanical testing to simulate methods that may be used to access liquid consumer products by young children.

1.3The test parameters provided within this test method are estimates based on existing literature and experience. The estimated values are intended to allow comparison of performance characteristics across different restricted delivery systems.

1.4This test method applies to liquids packaged in reclosable containers.

Note 1:Since there are many variables that may affect release of liquid (for example, rigidity of container, viscosity of liquid contents, or variation in test equipment), it is important that the entire restricted delivery system is tested together as intended for use while using the same or similar testing equipment. This test method does not address other product characteristics that might be affected by use of restricted delivery systems (for example, uniformity of active ingredient throughout duration of use).

1.5Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 02
DocumentType
Test Method
Pages
12
PublisherName
American Society for Testing and Materials
Status
Current

ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM D 7778 : 2015 Standard Guide for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 7778 : 2015 : R2022 : EDT 1 Standard Guide for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 7778 : 2012 Standard Guide for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

View more information
£58.92
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.