CEI EN 61400-12-1 : 2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WIND POWER GENERATION SYSTEMS - PART 12-1: POWER PERFORMANCE MEASUREMENT OF ELECTRICITY PRODUCING WIND TURBINES
Hardcopy , PDF
English
01-01-2007
17-07-2025
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Power performance method overview
6 Preparation for performance test
7 Test equipment
8 Measurement procedure
9 Derived results
10 Reporting format
Annex A (normative) - Assessment of influences
caused by wind turbines and obstacles
at the test site
Annex B (normative) - Assessment of terrain at
the test site
Annex C (normative) - Site calibration procedure
Annex D (normative) - Evaluation of uncertainty in
measurement
Annex E (informative) - Theoretical basis for determining
the uncertainty of measurement using the method of bins
Annex F (normative) - Wind tunnel calibration procedure
for anemometers
Annex G (normative) - Mounting of instruments on the
meteorological mast
Annex H (normative) - Power performance testing of
small wind turbines
Annex I (normative) - Classification of cup and sonic
anemometry
Annex J (normative) - Assessment of cup and sonic
anemometry
Annex K (normative) - In-situ comparison of anemometers
Annex L (normative) - The application of remote
sensing technology
Annex M (informative) - Normalisation of power curve data
according to the turbulence Intensity
Annex N (informative) - Wind tunnel calibration procedure
for wind direction sensors
Annex O (informative) - Power performance testing in
cold climate
Annex P (informative) - Wind shear normalisation procedure
Annex Q (informative) - Definition of the rotor equivalent
wind speed under consideration of wind veer
Annex R (informative) - Uncertainty considerations
for tests on multiple turbines
Annex S (informative) - Mast flow distortion
correction for lattice masts
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Describes the procedure for measuring the power performance characteristics of a single wind turbine and applies to the testing of wind turbines of all types and sizes connected to the electrical power network.
| Committee |
CT 88
|
| DevelopmentNote |
Classificazione CEI 88-5. (03/2007) Supersedes CEI EN 61400-12. (10/2007) 2ED 2007 Edition is valid until 07-04-2020. (12/2017)
|
| DocumentType |
Standard
|
| Pages |
98
|
| PublisherName |
Comitato Elettrotecnico Italiano
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| IEC 61400-12-1:2017 | Identical |
| EN 61400-12-1:2017 | Identical |
| CEI EN IEC 61400-12-5:2023-03 | Wind power generation systemsPart 12-5: Power performance -Obstacle and terrain assessment |
| EN 60688:2013 | Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| IEC 61869-3:2011 | Instrument transformers - Part 3: Additional requirements for inductive voltage transformers |
| EN 61400-12-2:2013/AC:2016-10 | WIND TURBINES - PART 12-2: POWER PERFORMANCE OF ELECTRICITYPRODUCING WIND TURBINES BASED ON NACELLE ANEMOMETRY (IEC 61400-12-2:2013/COR1:2016) |
| IEC 61869-2:2012 | Instrument transformers - Part 2: Additional requirements for current transformers |
| IEC 60688:2012 | Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals |
| EN 61869-3:2011 | Instrument transformers - Part 3: Additional requirements for inductive voltage transformers |
| EN ISO/IEC 17043:2010 | Conformity assessment - General requirements for proficiency testing (ISO/IEC 17043:2010) |
| EN 61869-2:2012 | Instrument transformers - Part 2: Additional requirements for current transformers |
| IEC 61869-1:2007 | Instrument transformers - Part 1: General requirements |
| ISO 2533:1975 | Standard Atmosphere |
| EN 61869-1:2009 | Instrument transformers - Part 1: General requirements |
| ISO/IEC 17043:2010 | Conformity assessment — General requirements for proficiency testing |
| ISO 3966:2008 | Measurement of fluid flow in closed conduits — Velocity area method using Pitot static tubes |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.