MIL-F-18280 Revision F:1995
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FITTING, FLARELESS TUBE, FLUID CONNECTION
Available format(s)
PDF
Superseded date
18-06-1999
Publisher
Specifies flareless tube connection fittings, sleeves and nuts used in fluid systems.
Committee |
FSC 4730
|
DocumentType |
Standard
|
Pages |
39
|
PublisherName |
US Military Specs/Standards/Handbooks
|
Status |
Superseded
|
SupersededBy |
MIL-H-25475 Revision B:1971 | HYDRAULIC SYSTEM, MISSILE, DESIGN, INSTALLATION TESTS AND DATE REQUIREMENTS, GENERAL REQUIREMENTS FOR |
MIL C 25427 : A | COUPLING ASSEMBLY, HYDRAULIC, SELF-SEALING, QUICK DISCONNECT |
MIL-HDBK-1655 Base Document:1997 | CLASSIFICATION OF DEFECTS OF FLARELESS AND BEAM SEAL FITTINGS |
MIL F 8789 : D | FITTING END, ATTACHABLE HYDRAULIC, HIGH PRESSURE HOSE |
DOD-STD-35-20 Revision C:1986 | AUTOMATED ENGINEERING DOCUMENT PREPARATION SYSTEM, FITTINGS AND COUPLINGS |
MIL-STD-1655 Base Document:1975 | FITTINGS, FLARELESS, CLASSIFICATION OF DEFECTS OF |
MIL-T-21578 Revision A:1966 | TEST EQUIPMENT, HAZARDOUS LOCATION, INSTALLED, BASIC REQUIREMENTS FOR |
MS21907 Revision G:1991 | ELBOW, BULKHEAD UNIVERSAL, 45 DEGREE, FLARELESS TUBE |
SAE AIR 1388 : 1992 | SERVICE DAMAGE LIMITS FOR AIRCRAFT HYDRAULIC TUBING |
SAE AS 4444/1 : 2013 | SLEEVE, BITE TYPE, 24 DEGREE CONE FLARELESS FITTING |
SBAC TS 100 : 2 | BRITISH METRIC SWAGED PIPE COUPLING (AS 43020 AND AS 43090 SERIES): TYPE APPROVAL TEST REQUIREMENTS |
MIL-I-18802 Revision A:1962 | INSTALLATION OF FUEL AND OIL LINES, AIRCRAFT |
MIL-F-45764 Revision C:1990 | FLUID LINES & FITTINGS FOR MISSILES & RELATED GROUND EQUIPMENT, FABRICATION & INSTALLATION OF |
SAE ARP 1185 : 2013 | FLEXURE TESTING OF HYDRAULIC TUBING JOINTS AND FITTINGS |
MIL-HDBK-270 Revision A:1991 | METALLIC MATERIALS FOR LOW MAGNETIC APPLICATIONS, MAGNETIC PERMEABILITY AND ELECTRICAL CONDUCTIVITY, CHARACTERISTICS OF (METRIC) |
SAE AS 4444 : 2013 | FITTINGS, 24 DEGREE CONE FLARELESS, FLUID CONNECTION, 5000 PSI |
MIL R 83055 : 0 | RAIN REPELLENT DISPENSING SYSTEMS, AIRCRAFT WINDSHIELD, GENERAL SPECIFICATION FOR |
SAE AS 18802 : 2013 | FUEL AND OIL LINES, AIRCRAFT, INSTALLATION OF |
SAE AIR 310 : 2013 | FITTINGS, CATALOG OF FLARED. FLARELESS, PIPE THREADED, PORT, HOSE AND OTHER TYPE TUBE STANDARD CONNECTORS |
SAE MA 2005 : 2015 | TUBE FITTINGS, AEROSPACE FLUID SYSTEMS, SEPARABLE, FOR 24 DEGREE CONE, GENERAL SPECIFICATION, METRIC |
SAE AS 25427 : 2015 | COUPLING ASSEMBLY, HYDRAULIC, SELF-SEALING, QUICK DISCONNECT |
MS21909 Revision G:1990 | TEE, BULKHEAD AND UNIVERSAL, FLARELESS TUBE |
MIL J 5513 : C | JOINT, HYDRAULIC SWIVEL |
SAE AS 4444/2 : 2015 | Fitting, 24° Cone Flareless to 37° Flared, Fluid Connection |
SAE AMS 2486 : 2010 | CONVERSION COATING OF TITANIUM ALLOYS FLUORIDE-PHOSPHATE TYPE |
QQ-A-225-9 Revision E:1982 | ALUMINUM ALLOY BAR, ROD, WIRE, AND SPECIAL SHAPES, ROLLED, DRAWN, OR COLD FINISHED, 7075 |
SAE AMS 2241 : 2016 | TOLERANCES, CORROSION AND HEAT-RESISTANT STEEL, IRON ALLOY, TITANIUM, AND TITANIUM ALLOY BARS AND WIRE |
SAE ARP 603 : 1985 | IMPULSE TESTING OF HYDRAULIC HOSE, TUBING, AND FITTING ASSEMBLIES |
MIL H 46170 : B | HYDRAULIC FLUID, RUST INHIBITED, FIRE-RESISTANT, SYNTHETIC HYDROCARBON BASE |
QQ-P-35 Revision C:1988 | PASSIVATION TREATMENTS FOR CORROSION-RESISTANT STEEL |
SAE AMS 4911 : 2014 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4 V, ANNEALED |
SAE AMS 2488 : 2000 | ANODIC TREATMENT - TITANIUM AND TITANIUM ALLOYS SOLUTION PH 13 OR HIGHER |
MIL-T-6845 Revision D:1985 | TUBING, STEEL, CORROSION-RESISTANT (304) AEROSPACE VEHICLE HYDRAULIC SYSTEM 1/8 HARD CONDITION |
MIL-STD-1655 Base Document:1975 | FITTINGS, FLARELESS, CLASSIFICATION OF DEFECTS OF |
QQ-A-367 Revision H:1973 | ALUMINUM ALLOY FORGINGS |
ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
MIL-T-9046 Revision J:1983 | TITANIUM AND TITANIUM ALLOY, SHEET, STRIP AND PLATE |
SAE ARP 891 : 1976 | DETERMINATION OF ALUMINUM ALLOY TEMPERS THROUGH ELECTRICAL CONDUCTIVITY MEASUREMENT (EDDY CURRENT) |
QQ A 225/6 : E | ALUMINUM ALLOY BAR, ROD, AND WIRE, ROLLED, DRAWN OR COLD FINISHED, 2024 |
MIL-STD-6866 Base Document:1985 | INSPECTION, LIQUID PENETRANT |
MIL H 83282 : C | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, AIRCRAFT, METRIC, NATO CODE NUMBER H 537 |
MIL H 6083 : E | HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION |
SAE AS 1376 : 2013 | ALTERNATE DIMENSIONS, CENTER BODY SECTION, SHAPE FLUID FITTING, DESIGN STANDARD |
MIL-S-8879 Revision C:1991 | SCREW THREADS, CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER, GENERAL SPECIFICATION FOR |
MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
QQ-S-763 Revision F:1996 | STEEL BARS, WIRE, SHAPES AND FORGINGS; CORROSION RESISTANT |
MIL-H-6088 Revision G:1991 | HEAT TREATMENT OF ALUMINIUM ALLOYS |
MIL H 5606 : G | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE |
QQ-P-416 Revision F:1991 | PLATING, CADMIUM (ELECTRODEPOSITED) |
MIL L 46010 : D | LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING |
FED-STD-595 Revision C:2008 | COLORS USED IN GOVERNMENT PROCUREMENT |
SAE AMS 4928 : 2016 | TITANIUM ALLOY BARS, WIRE, FORGINGS, RINGS, AND DRAWN SHAPES, 6AL - 4V, ANNEALED |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.