• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 8056 : 2018

Current

Current

The latest, up-to-date edition.

Standard Guide for Elemental Analysis of Crude Oil

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-06-2018

1.1This guide summarizes the current information about the test methods for elemental and associated analyses used in the analysis of crude oils. This information can be helpful in trade between the buyers and sellers of crude oil. Elemental analyses tests form an important part of quantifying the crude oil quality.

1.2The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Guide
Pages
14
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 7260 : 2019 Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants

ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 2622 : 1992 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 5863 : 2022 Standard Test Methods for Determination of Nickel, Vanadium, Iron, and Sodium in Crude Oils and Residual Fuels by Flame Atomic Absorption Spectrometry
ASTM D 129 : 2018 Standard Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method) (Withdrawn 2023)
ASTM D 5291 : 2021 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 1548 : 1992 : EDT 1 Test Method for Vanadium in Navy Special Fuel Oil (Withdrawn 1997)
ASTM D 5708 : 2005 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 6792 : 2021 : REV A Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 1552 : 2003 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 4057 : 1995 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4929 : 1999 : EDT 1 Standard Test Methods for Determination of Organic Chloride Content in Crude Oil
ASTM D 2622 : 1987 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 7482 : 2017 : R2023 Standard Practice for Sampling, Storage, and Handling of Hydrocarbons for Mercury Analysis
ASTM D 7343 : 2007 Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 5291 : 2010 : R2015 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 6299 : 2010 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3230 : 1999 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 7622 : 2010 : R2015 Standard Test Method for Total Mercury in Crude Oil Using Combustion and Direct Cold Vapor Atomic Absorption Method with Zeeman Background Correction
ASTM D 3227 : 2000 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 6299 : 2013 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6259 : 1998 : R2004 Standard Practice for Determination of a Pooled Limit of Quantitation
ASTM D 3230 : 2009 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 5708 : 2015 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 4177 : 2016 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4929 : 2007 : R2014 Standard Test Methods for Determination of Organic Chloride Content in Crude Oil
ASTM D 3228 : 2008 : R2019 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 5762 : 2009 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 3228 : 2019 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 5185 : 1997 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 5863 : 2000 : REV A : R2011 Standard Test Methods for Determination of Nickel, Vanadium, Iron, and Sodium in Crude Oils and Residual Fuels by Flame Atomic Absorption Spectrometry
ASTM D 4629 : 2002 : R2007 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 7621 : 2016 : R2021 Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 7621 : 2014 Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 6299 : 2017 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2017 : REV B Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 5291 : 1992 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 6299 : 2009 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 1552 : 2008 : R2014 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 7260 : 2020 Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 4177 : 1995 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 7343 : 2020 Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 482 : 2013 Standard Test Method for Ash from Petroleum Products
ASTM D 4057 : 2012 : R2018 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4294 : 2010 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 6299 : 2013 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6792 : 2006 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 6299 : 2021 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 1552 : 1990 : EDT 1 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 7621 : 2010 Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction <a href="#fn00002"></a>
ASTM D 7621 : 2016 Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 5291 : 2010 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 6792 : 2004 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 4929 : 2015 Standard Test Methods for Determination of Organic Chloride Content in Crude Oil
ASTM D 5762 : 2002 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 5762 : 2001 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 2622 : 1998 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 1552 : 2016 Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conducitivity Detection (TCD)
ASTM D 5854 : 1996 : R2010 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 7455 : 2008 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 4929 : 2019 : REV A Standard Test Method for Determination of Organic Chloride Content in Crude Oil
ASTM D 6299 : 2010 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3227 : 2002 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 3230 : 2005 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 6299 : 2022 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 7260 : 2012 Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 5185 : 2005 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4929 : 2022 Standard Test Method for Determination of Organic Chloride Content in Crude Oil
ASTM D 4629 : 2009 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 3230 : 2013 : R2018 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 4057 : 1981 : EDT 2 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 7578 : 2018 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 7455 : 2014 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 3228 : 2001 Standard Test Method for Total Nitrogen In Lubricating Oils and Fuel Oils By Modified Kjeldahl Method
ASTM D 5708 : 2000 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 5185 : 2002 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 5854 : 2019 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 4629 : 1996 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 1552 : 2000 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 2622 : 2008 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 7623 : 2010 : R2015 Standard Test Method for Total Mercury in Crude Oil Using Combustion-Gold Amalgamation and Cold Vapor Atomic Absorption Method
ASTM D 7623 :2010 Standard Test Method for Total Mercury in Crude Oil Using Combustion-Gold Amalgamation and Cold Vapor Atomic Absorption Method
ASTM D 6792 : 2021 : REV B Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 7740 : 201 Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants
ASTM D 6259 : 2015 Standard Practice for Determination of a Pooled Limit of Quantitation for a Test Method
ASTM D 3228 : 2008 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 6792 : 2023 : REV C Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 6470 : 1999 : R2015 Standard Test Method for Salt in Crude Oils (Potentiometric Method)
ASTM D 5863 : 2000 : REV A Standard Test Methods for Determination of Nickel, Vanadium, Iron, and Sodium in Crude Oils and Residual Fuels by Flame Atomic Absorption Spectrometry
ASTM D 5185 : 2018 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 6299 : 2023 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 5762 : 2005 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 5854 : 1996 : R2005 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 5762 : 2018 Standard Test Method for Nitrogen in Liquid Hydrocarbons, Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 6470 : 1999 : R2010 Standard Test Method for Salt in Crude Oils (Potentiometric Method)
ASTM D 6792 : 2004 : REV A Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 3228 : 2008 : R2014 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 5291 : 2016 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 3227 : 2013 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 6792 : 2005 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 5185 : 2013 : EDT 1 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 6299 : 2000 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6259 : 1998 Standard Practice for Determination of a Pooled Limit of Quantitation
ASTM D 5708 : 2012 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 6299 : 2010 : EDT 2 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 5863 : 2000 : REV A : R2005 Standard Test Methods for Determination of Nickel, Vanadium, Iron, and Sodium in Crude Oils and Residual Fuels by Flame Atomic Absorption Spectrometry
ASTM D 5291 : 2002 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 3230 : 2010 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 4929 : 1999 Standard Test Methods for Determination of Organic Chloride Content in Crude Oil
ASTM D 6299 : 2016 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3230 : 1999 : R2004 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 3230 : 2008 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 6792 : 2023 : REV B Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 1552 : 2023 Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD)
ASTM D 5863 : 2000 : REV A : R2016 Standard Test Methods for Determination of Nickel, Vanadium, Iron, and Sodium in Crude Oils and Residual Fuels by Flame Atomic Absorption Spectrometry
ASTM D 3228 : 2022 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 4057 : 2006 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4294 : 2008 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 4929 : 2004 Standard Test Methods for Determination of Organic Chloride Content in Crude Oil
ASTM D 4177 : 2015 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 7372 : 2012 Standard Guide for Analysis and Interpretation of Proficiency Test Program Results
ASTM D 6792 : 2020 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 6299 : 2019 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6792 : 2021 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 6259 : 1998 : R2010 Standard Practice for Determination of a Pooled Limit of Quantitation
ASTM D 4929 : 2015 : REV A Standard Test Methods for Determination of Organic Chloride Content in Crude Oil
ASTM D 7691 : 2011 : EDT 1 Standard Test Method for Multielement Analysis of Crude Oils Using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4057 : 2012 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6299 : 2023 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2000 : REV A Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6792 : 2013 Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 7578 : 2010 : EDT 1 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 5185 : 2013 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 2622 : 2003 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 7621 : 2012 Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 4294 : 2008 : REV A Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 6792 : 2017 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 5762 : 2012 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 7691 : 2011 Standard Test Method for Multielement Analysis of Crude Oils Using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 7621 : 2015 Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 5762 : 2017 Standard Test Method for Nitrogen in Liquid Hydrocarbons, Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 4294 : 2002 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 7740 : 2011 : R2016 Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants
ASTM D 1552 : 2016 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD)
ASTM D 3228 : 2020 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 1552 : 2007 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 6792 : 2007 Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 4929 : 2007 Standard Test Methods for Determination of Organic Chloride Content in Crude Oil
ASTM D 4177 : 2022 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 1552 : 1995 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 4629 : 2002 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 7372 : 2007 Standard Guide for Analysis and Interpretation of Proficiency Test Program Results
ASTM D 6792 : 2021 : REV C Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 6470 : 1999 : R2020 Standard Test Method for Salt in Crude Oils (Potentiometric Method)
ASTM D 6299 : 2023 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2020 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 7482 : 2017 Standard Practice for Sampling, Storage, and Handling of Hydrocarbons for Mercury Analysis
ASTM D 5291 : 2002 : R2007 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 4177 : 1995 : R2010 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 1552 : 2015 Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and IR Detection
ASTM D 6259 : 2015 : R2019 Standard Practice for Determination of a Pooled Limit of Quantitation for a Test Method
ASTM D 5762 : 1998 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 1552 : 2001 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 3228 : 2003 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 7482 : 2014 Standard Practice for Sampling, Storage, and Handling of Hydrocarbons for Mercury Analysis
ASTM D 6299 : 2008 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3228 : 1996 Standard Test Method for Total Nitrogen In Lubricating Oils and Fuel Oils By Modified Kjeldahl Method
ASTM D 6792 : 2023 : REV A Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 4294 : 2016 : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 5708 : 2011 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 4177 : 1995 : R2000 Standard Practice for Automatic Sampling of Peroleum and Petroleum Products
ASTM D 1552 : 2008 : R2014 : EDT 1 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 7343 : 2018 Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 8150 : 2022 Standard Test Method for Determination of Organic Chloride Content in Crude Oil by Distillation Followed by Detection Using Combustion Ion Chromatography
ASTM D 7691 : 2016 Standard Test Method for Multielement Analysis of Crude Oils Using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 7578 : 2020 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 5854 : 1996 : R2000 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 6259 : 2023 Standard Practice for Determination of a Pooled Limit of Quantitation for a Test Method
ASTM D 7343 : 2012 Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 4294 : 2008 : REV A : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 4629 : 2017 Standard Test Method for Trace Nitrogen in Liquid Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 6299 : 2002 : EDT 1 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
ASTM D 7621 : 2013 Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 4294 : 1998 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 4629 : 2012 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 5863 : 2000 Standard Test Methods for Determination of Nickel, Vanadium, Iron, and Sodium in Crude Oils and Residual Fuels by Flame Atomic Absorption Spectrometry
ASTM D 7343 : 2012 : R2017 Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 5708 : 2002 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 2622 : 2010 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4294 : 2021 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 5185 : 2009 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4629 : 2012 : R2017 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 5291 : 2001 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 7482 : 2008 Standard Practice for Sampling, Storage, and Handling of Hydrocarbons for Mercury Analysis
ASTM D 7621 : 2015 : REV A Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 2622 : 2021 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 6299 : 2022 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3227 : 2024 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 4929 : 2016 Standard Test Method for Determination of Organic Chloride Content in Crude Oil
ASTM D 3230 : 2005 : REV A Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 4629 : 2008 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 5762 : 2010 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 3227 : 2004 : REV A : R2010 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 5291 : 1996 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 6792 : 2022 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 7578 : 2010 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 2622 : 2007 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 6470 : 1999 : R2004 Standard Test Method for Salt in Crude Oils (Potentiometric Method)
ASTM D 4629 : 2010 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
ASTM D 3227 : 2004 : REV A Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 2622 : 1994 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 4057 : 2022 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 5708 : 2015 : R2020 : EDT 1 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 1552 : 2008 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 2622 : 2005 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4177 : 2016 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 7260 : 2019 Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 5185 : 2002 : EDT 1 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4294 : 2003 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry
ASTM D 5762 : 2008 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 6792 : 2003 Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 5762 : 2012 : R2017 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 4177 : 2020 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 1995 : R2005 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 7622 : 2010 : EDT 1 Standard Test Method for Total Mercury in Crude Oil Using Combustion and Direct Cold Vapor Atomic Absorption Method with Zeeman Background Correction
ASTM D 4294 : 2016 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 8150 : 2017 Standard Test Method for Determination of Organic Chloride Content in Crude Oil by Distillation Followed by Detection Using Combustion Ion Chromatography
ASTM D 5854 : 2019 : REV A Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 6792 : 2002 Standard Guide for A Quality System in Petroleum Products and Lubricants Testing Laboratories
ASTM D 5185 : 2002 : EDT 2 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 6470 : 1999 Standard Test Method for Salt in Crude Oils (Potentiometric Method)
ASTM D 3227 : 2004 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 3230 : 2013 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 7260 : 2006 Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 6299 : 2007 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6792 : 2023 Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 6299 : 2007 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 7622 : 2010 Standard Test Method for Total Mercury in Crude Oil Using Combustion and Direct Cold Vapor Atomic Absorption Method with Zeeman Background Correction
ASTM D 4057 : 1995 : R2000 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 3230 : 2006 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 6299 : 2020 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 7372 : 2017 Standard Guide for Analysis and Interpretation of Proficiency Test Program Results
ASTM D 4177 : 2022 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 1552 : 2016 : R2021 Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conductivity Detection (TCD)
ASTM D 3227 : 2016 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 7455 : 2019 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 6299 : 2017 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 5708 : 2012 : EDT 1 Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry
ASTM D 4177 : 2015 : REV A Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 6792 : 2022 : REV A Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories
ASTM D 3227 : 2002 : REV A Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 7578 : 2015 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 4057 : 2006 : R2011 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 1552 : 1983 Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
ASTM D 7372 : 2021 Standard Guide for Analysis and Interpretation of Proficiency Test Program Results
ASTM D 5291 : 2009 Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
ASTM D 7621 : 2015 : REV B Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction
ASTM D 5762 : 2018 : REV A Standard Test Method for Nitrogen in Liquid Hydrocarbons, Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 3228 : 2005 Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
ASTM D 4929 : 2017 Standard Test Method for Determination of Organic Chloride Content in Crude Oil
ASTM D 4929 : 2019 Standard Test Method for Determination of Organic Chloride Content in Crude Oil
ASTM D 5762 : 2011 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
ASTM D 5854 : 1996 : R2015 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 7691 : 2023 Standard Test Method for Multielement Analysis of Crude Oils Using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4294 : 1990 : R1998 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 3230 : 2019 Standard Test Method for Salts in Crude Oil (Electrometric Method)
ASTM D 3227 : 2023 Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 7482 : 2015 Standard Practice for Sampling, Storage, and Handling of Hydrocarbons for Mercury Analysis
ASTM D 7260 : 2017 Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 6299 : 2002 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance

View more information
£57.60
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.